How To
How To
1869 results
-
Yes, the Harman Kardon SB20 features IR learning functionality. Please follow these steps:
- Power on your Harman Kardon SB20.
- Press and hold the SB20 surround button for 5 seconds. This will make the system enter IR learning mode. The power button will flash amber while in learning mode.
- Now the SB20 can learn to respond to your TV remote control. These commands can be learned: To learn the SB 20 VOL+ command, press volume + on the SB 20 top panel, then press VOL+ on your TV remote control. The power button should blink amber, and the surround button will light up for 1 second. This will indicate that the process was successful. Repeat the procedure for volume-, mute and power on/off.
- To exit the learning mode, press and hold the surround button for 5 seconds again. The power button light goes out.
Was this helpful? Thank you for your feedback! -
Yes, they are quite easy to remove, and with a little care, new ear pads can be fitted in one or two minutes. You can do this yourself.Was this helpful? Thank you for your feedback!
-
Yes, press Volume + and Surround button at the same time for 5 seconds.Was this helpful? Thank you for your feedback!
-
Yes, this can be done very easily by doing the following procedure: 1: Power on the Cinema Base. 2: Simultaneously press the “Surround” and “VOL –” buttons (at the same time). 3: The Cinema Base source LED button will light amber in color, for 1 second, then the power button LED light will go off and on. 4: Your Cinema Base is now reset.Was this helpful? Thank you for your feedback!
-
Yes, by holding down Volume+ and surround button for more than 5 seconds will reset the SB20. The SB20 will automatically reboot itself, after it has been reset.Was this helpful? Thank you for your feedback!
-
Yes, switch the soundbar ON, then press the volume - ( minus ) and surround buttons at the same time for 5 seconds. Now the device is reset.Was this helpful? Thank you for your feedback!
-
The JBL Cinema SB450 can be reset to its default factory settings and erasing all programming. To reset the soundbar, press and hold Volume+ and Virtual Surround buttons for 5s.Was this helpful? Thank you for your feedback!
-
There are 5 leds which indecates the current charge level, Each led indicates 20% of charge.Was this helpful? Thank you for your feedback!
-
No, NC is always on when Bluetooth is on. However, it is possible to select NC on or off when listening via cable.Was this helpful? Thank you for your feedback!
-
No. There is no way to turn off the blue LED light from our wireless headphones unless they are turned off.Was this helpful? Thank you for your feedback!
-
Yes, Alexa has various voice commands to turn up the volume. Try saying "Alexa, turn it up" or "Alexa, set volume to 5".Was this helpful? Thank you for your feedback!
-
While this is indeed possible, no such cable is made by AKG, so only cables from third-party manufacturers may be considered. Please note that internal pin configuration must be identical to the original cable for such a cable to work with the headphones.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call Us now at:
(877) 871-6755
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat with Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)