How To
How To
1869 results
-
This can be caused by dirt and dust accumulating on the charging arm, which can reduce the effectiveness of the adhesive. Clean the surface of the charging arm with a wet cloth or alcohol wipes. Do not use paper towels as these can leave paper debris.Was this helpful? Thank you for your feedback!
-
There are two ways to blow speakers. The first is the one we all know and understand. If you pump 500 watts into a speaker that is only rated at 100 watts, kaboom, it blows up. As a result, very few of us do this. So then why are all of these poor, helpless speakers blowing up? Because of the second reason, under-powering. It's really a misleading term, but let's try to explain. First let's take it to the maximum. Example: You have a 1000 watt speaker and a 100 watt amplifier. The way you like to listen to music requires 300 watts. Typically, you will ask your amp to put out that 300 watts that you want to hear. The amp will do it, but it will clip and distort. Unfortunately, the human ear can't hear distortion until it reaches almost 10%. By that time it's usually too late. The speaker keeps trying to reproduce this distortion that it's not capable or reproducing and eventually it blows (usually the tweeter fails first). If you are blowing speakers with an amp that has a power rating lower than your speakers, you are pushing your amp too far, causing it to clip, and blowing speakers. If you are pushing your system too hard, it is suggested that you realize your systems limitations or recommend that you get a more powerful amplifier. Please realize, if you only buy speakers that will handle more power and not a more powerful amplifier, you won't solve the problem. The speakers will still blow, because it is distortion that is blowing them, not too much power.Was this helpful? Thank you for your feedback!
-
Our Control X Wireless speaker has two different patterns for switching on, when using either battery or AC power. When using battery, turning on one speaker in either stereo mode or association mode (4 speakers connected), all will turn on simultaneously, no matter which is primary or secondary. When connected to AC power, switch on the primary speaker in stereo or associated mode, and the secondary speakers will follow. If you have associated speakers stereo or 4 speakers connected, then you have to press primary speaker's power button for more than 2 seconds, then the primary will send signal to secondaries, and they will wake up. It takes approx. 30-60 seconds before all are switched on. If your press it too short (less than 2 seconds), the primary speaker will not "pair" the secondary speakers together. Switch off the primary and start over again.Was this helpful? Thank you for your feedback!
-
Do not worry, pairing both devices is easy and quick. Press the "pairing" button on the back of the Omni Bar, then press "pairing" button on the subwoofer. They will start communicating with each other, and when both devices show white light in the LED on the back, that indicates that they are paired.Was this helpful? Thank you for your feedback!
-
Some mobile phones, tablet computers or laptop computers will react to the powerful magnetic field from the loudspeaker drive units that are right beneath the top panel. Some have magnetic sensors built in, which means that covers with magnets in the lid can turn the phone ON when the cover lid is opened, and turn it OFF again when the lid is closed. Such phones may turn off if placed on certain portions of the top panel. Other devices are simply sensitive to magnetic fields. You can move the device around on the top of your L8 or L16 speaker, to check if some locations are better than others. The magnetic fields are most powerful near the front panel, where the speaker units are mounted. If you cannot find a location which works, your particular phone, tablet or laptop cannot be used while resting on the top panel of your speaker. There are no reports of damage to any devices because of this phenomenon.Was this helpful? Thank you for your feedback!
-
This is most likely due to CEC function. Some our soundbars supports CEC commands from your TV, and if some CEC commands will make the speaker react in a way you do not like, we suggest you disable all CEC functions from your TV. Please note, that your Soundbar will not turn on when your TV is turned on, due to disabling the CEC function.Was this helpful? Thank you for your feedback!
-
Check your audio cables and make sure they are secure. Set the volume of the source device (if applicable) to a higher level.Was this helpful? Thank you for your feedback!
-
When you are installing new apps or adding content to your LINK BAR, the system may be a bit slower when dealing with multiple things.
Here is a couple of things you should know.- You need a speedy internet connection to download all the content you added.
- Wait for everything to be finished, then you can enjoy the system without any issues.
- Reboot LINK BAR after installing all apps. A fresh reboot can help and enhance performance.
Was this helpful? Thank you for your feedback! -
If you find yourself encountering audio dropouts or interference coming from your surround speakers when they are not docked on the main unit, here are a couple of tips to try to remedy that.
1. Try moving any wireless routers that are near the sound bar further away.
2. Reboot router so it can auto select a new frequency channel, since the sound bar and router may be on the same channel resulting in audible interferences
3. Re-position the surround speakers so they are closer to the main unit.
4. Re-calibrate the surround speakers
5. Adjust the volume on the sound bar and gradually raise the volume, if driven to hard the sound bar speakers can distort
Was this helpful? Thank you for your feedback! -
Yes, rinse it under a faucet or under the shower, but not under full water pressure.Was this helpful? Thank you for your feedback!
-
N400NC
Software Update Release Notes
------------------------------------------------------------------------
Version: 4.1.0
Release Date: November 4, 2021
What’s New
- Fixed issue where there was no sound when using earbuds with conference software on pc, i.e. Zoom, WebEx, Skype
- Performance improved
Was this helpful? Thank you for your feedback! -
N5 Hybrid
Software Update Release Notes
------------------------------------------------------------------------
Version: 3.8.0
Release Date: March 15, 2024
What’s New
- Add support for Google Audio Switch
- Stability and performance improvement
------------------------------------------------------------------------
Version: 3.6.0
Release Date: January 15, 2024
What’s New
- Change Max Volume limiter default back to off
- Enhance Silent Mode, Ambien Sound Mode, & Private Call Mode
- Personi-fi function set to off after power cycle
Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call Us now at:
(877) 871-6755
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat with Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)