The distance between wall-mounts centers are: JBL BAR Studio: 45 cm. JBL BAR 2.1: 70 cm. JBL BAR 3.1: 70 cm. JBL BAR 5.1: 61 cm JBL BAR 5.1 Surround: 71.85 cm JBL BAR 9.1: 55,5 cm

Playing time is up to 20 hours.

The Frequency response for the Citation series, except the subwoofer, is 50Hz to 20Khz.
 

The EQ Button activates a special "wide stereo sound" effect. It does not affect bass settings. Turning EQ On/Off does not reset bass level to default value. User can adjust BASS in the Bass +/- control in the APP.

Software version v.7.9 is the latest for the Flip 3

JBL Bar 9.1 is 884 mm (without the surrounds in charging position). Surrounds add approx. 160 mm on each side, in charging position.

The same as the 8 ohm output, 125 watts/channel.

Wireless Dual Sound feature supports a maximum of two speakers. Both the GO + PLAY MINI and the other speaker must have the Dual Sound feature.

The maximum video resolution of the No. 40 HDMI card is 1080i.

The No.536 has several operational and standby modes - the measurements below represent typical values measured at 120VAC: Mode Typical Power Consumption Notes On 210 Watts With no input or output loading Normal (standby) 4.1 Watts/100 Watts Unpon initial power-up/After first use Power Save (Standby) 4.1 Watts Green (Standby) 0.3 Watts OFF 0 Watts Via rear panel switch Note that the No. 536 cannot be shut off by the front button – this is used only for switching the amp in/out of a standby mode. Also note that when set to the Normal standby mode, the amplifier will initially consume the same power as when in the Powersave mode but will change to a higher level after it is switched on for the first time.

The No. 585 will deliver 350 watts into 4 ohms

The overall power rating is 630 W maximum power at 1% THD.
 

With the speaker ON, press and hold the VOL+ and Pause/Play buttons for 5-6 seconds. The Xtreme shuts down, and is now reset. You will need to 'forget' the speaker in Bluetooth settings on your phone/tablet in order to pair it again.

Speakers will dual tweeters gives listeners the ability to have a single speaker to drive two independent channels, ideally stereo left and right. Dual tweeter speakers are usually used for in-ceiling audio applications. They have four terminals (two sets of positives and negatives) used to plug in speaker wires from the amplifier.

The audio level adjustment is a dedicated control for adjusting the tweeter’s high frequency volume. It allows you attenuate up to 3dB, based on your environment and/or preference.

The range is approximately 10 meters, depending on the environment.

The Omni 50+ rated power with AC power connected is 4 X 25 Watt. When using battery only, the rated power is 4 X 15 Watt.

Both the OMNI BAR+ and its subwoofer have 200W of power amplification, which means that total system power is 400 W.

These are the supported languages for the Everest GA series.

• English (US, UK, CA, IN, AU)
• German
• French (CA, FR)
• Japanese
• Portuguese (BR)

More will be added in future Google releases.

This connection is intended for software and service updates only.

Voltage is 100 - 240 Volt AC. Maximum power consumption is 120 Watts.

Soundgear Sense provides two wearing styles, either as regular TWS headphones with an ear hook for a secure fit, or as a neckband headphone with the optional detachable neckband. Both wearing styles offer the same open ear experience with rich, full-range sound, it is just a matter of your own preference or use case which wearing style you choose. 

Now, with Google Assistant and Alexa available simultaneously on your JBL Authentics speakers, you can choose to use one or both voice services available. This means you can set up just Alexa, just Google Assistant, or both. If you choose to set up both services, they will be at the ready. You can use either of them whenever you want simply by saying either “Hey Google” or “Alexa”.

Headphones are tuned on a finely calibrated, standardized fixture to meet our target sound profile – but our heads are not finely tuned, calibrated fixtures so the sound we actually hear is different from the designed curve due to variations in how the headphones fit on each of us, meaning most people do not hear the target sound of the headphone.    Harman’s TruNote auto calibration technology is a patented algorithm that calibrates the sound of the headphone to each individual by measuring the unique fit of the headphone to the user.  The system automatically adjusts the sound of the headphone, creating a personalized equalization that restores the sound of headphone to the design target. The headphone sound is automatically personalized to each individual ensuring that they hear JBL sound as we engineered it to sound = better audio

Windows Sonic is a virtual surround algorithm that is built into Windows 10 PCs. You can read more here:
https://docs.microsoft.com/en-us/windows/win32/coreaudio/spatial-sound

The Onyx Studio 8 features Wireless Stereo Boost which allows you to connect two Onyx Studio 8 speakers together for a more powerful listening experience. Please note: You cannot connect the Onyx Studio 8 to other Onyx Studio speakers such as the Onyx Studio 7, 6 and 5.

Wireless Stereo Boost allows you to connect two of the same model speakers together for a more powerful listening experience. 

To use this feature, hold the Bluetooth button on both speakers for more than 5 seconds.

The left & right channels can be swapped by tapping the Bluetooth button on the host speaker twice.

The JBL Quantum Stream microphone is compatible with the JBL QuantumENGINE software. You can customize or use the following settings/features via the JBL QuantumENGINE:

Microphone settings
Polar patters (Cardioid / Onnidirectional)
Equalizer
RGB LED Light colors + animations/effects
Update firmware + software

Only data to make Google Assistant more efficient and Google services faster. When interacting with the speaker you will receive more personalized feedback in the future.

The ITX models come with two sizes: size 5 and the larger size 7. They are referred to as the Limited Edition lock tongue and groove enhancers. You can purchase two pairs for $10 on the Yurbuds accessories and enhancers page.

The Vi headphones have a couple different sensors, including a touch sensor (for interacting with Vi), a gyroscope (for rotational motion), accelerometer (for movement or vibrations) and a barometer (for elevation / atmospheric pressure). Plus they house a “custom” sensor that uses visible-light and infrared LEDs along with photodiodes, all in the left ear bud, to determine your heart rate. The headphones can also talk to your iPhone/Android's GPS and Wi-Fi to help with figuring out location and other information.

The Smart Case only supports English, so even if you change the language in the JBL Headphones app, it will remain in English.

The JBL QuantumENGINE supports up to 20 languages. You can select the preferred language in the system section.

The ear cushions are made of protein leather.

The JBL Quantum Stream mic is compatible with the following platforms:

PC (Windows)
PlayStation 4
PlayStation 5
Nintendo Switch
Mobile*
Mac

* Most newer phones are compatible.

The JBL Quantum 910 Wireless headset is compatible via 3.5mm jack with PC, PlayStation, Xbox, Nintendo Switch, Mobile, Mac and VR. You can use the USB connection with PC, PlayStation and Nintendo Switch.

The JBL Quantum ONE headset is compatible via 3.5mm jack with PC, PlayStation, Xbox, Nintendo Switch, Mobile, Mac and VR. You can use the USB connection with PC.

The JBL Quantum TWS supports two types of wireless connection at the same time. It's compatible with any Bluetooth compatible devices while the USB wireless dongle enables compatibility with PC/Mac, PS4/5, Nintendo Switch^TM, TV and iPads and Android^TM devices with USB-Connection (Note: Type-C supports PS5 while type-A is compatible with all PlayStation^TM model).

The Harman Kardon Wireless HD Audio System uses UDP ports 6060 and 6080.

To have the best possible performance for OMNI+ system we advise to have a dual-band router with a powerful chipset and ram for best Wi-Fi performance. This will not only help our products to perform better and more stable, but your other devices at home will have more power and fewer interruptions. Please also be sure that your home Wi-Fi router has Multicast enabled, as our Omni+ system requires this feature enabled in order to work (same goes for Chromecast devices). Always connect our Omni+ system to 5 GHz Wi-Fi whenever possible to limit the risk of devices being slow or interrupted on 2.4GHz Wi-Fi.

Different games have different settings, but as a general rule, make sure that your game outputs multi-channel unprocessed audio. We recommend 7.1 surround, but 5.1 works too. Always disable any other processing (like DTS and Dolby).  

If you are having trouble with distortion or drop outs, try the following suggestions: 1. Move the audio source closer to the speakers. 2. Move the speakers closer to each other. 3. Make sure only one of the two speakers are connected to the audio source. If both are connected to the audio source, disconnect the connection between the audio source and the second speaker. 4. Make sure the audio source connects with one streaming speaker only, disconnect other Bluetooth connection. 5. Restart both your speakers and the audio source. 6. Make sure the environment is not congested by other wireless signals.

The first thing you’ll notice is that sound no longer feels like it’s “inside your head.” Suddenly it seems like the game audio is coming from high-quality loudspeakers—or the virtual game world—all around you.

It’s a different experience than you get with other headphones, and may take a little while to adjust to. For example, sounds coming from sources in the distance will seem farther away, as they would in real life. Even though you might be used to those sounds feeling closer with other headphones, JBL QuantumSURROUND provides hyper-accurate spatialization that can give you a competitive edge.

So spend some time dialing in the EQ to your liking, and see how real-world hearing helps you pinpoint enemies and bring the game to life. 
 

The standard size that comes on all Endurance Series models is the size 5. There are other sizes 6, 7, and 8 available on the yurbuds accessories and enhancers page that you can purchase for $10. Shipping and Handling is included.

It's matter of preference and choice, but our biggest speaker, Arena 180, will have the most powerful sound , but also requires some space. Our bookshelf speakers, Arena 120 & Arena 130, are also a nice addition to your home system, and will also provide powerful sound. These can be wall-mounted, which you might prefer over floor standing speakers. All of the Arena series will provide a good audio experience, so you won't go empty handed with any of them!

The Inspire Pro and the Focus Pro Performance Fit earphones both feature a dry microphone and 3-button control remote. These features allow convenient navigation of music on your iPod® or iPhone® during rigorous activity even during extended use. The components within the 3-button control/ dry mic® are specifically selected for compatibility with: iPhone® (3GS, 4, 4S, 5), iPod® (120GB & 160GB classic; 4th, 5th, & 6th generation nano; 3rd & 4th generation shuffle), iPod® Touch (1st, 2nd, 3rd, 4th generation) and iPad® (1, 2, 3, 4). Some features may work with other devices.

If your teammates can not hear you, make sure of the following:

USB is correctly plugged in
Only one voice chat application is in use while in-game.
The mic input is set to JBL Quantum Stream.
Mic gain is not turned all the way down
Mic is not muted (mute/unmute by pressing the touch panel on top of the mic). By default the RBG will indicate red for muted, and green for unmuted(active).

 

Let's run through some basic check marks to ensure we didn't miss anything while setting up your device.

1. Your Citation device is turned on
2. Check the password you have entered, and re-enter it again (typos can happen).
3. Make sure your mobile device has the initial support needed:
   1. Android 4.4 OS and higher
   2. Apple iOS 10 OS and higher
   3. The latest version of Google Home app
4. Your phone needs Bluetooth to be on 
5. Enable Location Service (Android only)
6. Plus you need to permit Google Home app to access your location on the phone (Android only).

The basic check is done, and we are now moving into your Wireless network setup.

1. Try moving your speaker closer to the Wireless network router 
2. Have you previously connected the speaker to your WiFi network?  If yes, look below or move to "Troubleshooting"
   1. Did you recently make any changes to your network, such as buying a new router, adding an extender, or maybe changed settings?

   2. Maybe your ISP (Internet Service Provider) did some changes, possibly even updating your Wireless router software.

If you still are experiencing issues connecting the device to your Wireless network, let's do some further troubleshooting.

Troubleshooting

1. Your WiFi router might need a reboot, unplug power for 1 minute and connect power again.
   1. While you are rebooting your WiFi router, we advise doing the same for your speaker. Simply disconnect power and reconnect power again.
   2. In case rebooting the speaker didn't work, let's try resetting your speaker by pressing the Reset Button for 5 seconds (Front LED will light up).
2. Go ahead with the setup again (remember to open Google Home app )
3. Reboot your mobile device

WiFi Network Troubleshooting

• Check your WiFi router settings. Be sure that UPnP (Universal Plug and Play) is enabled.
• Change Wireless channels on your WiFi router on 2.4G or 5G..
  • Avoid using other channels on 2.4G other than 1, 6 and 11. The rest are a NO-GO.
  • Keep a maximum of 8 devices in total on 2.4G (that is including our speakers).
  • Move products to WiFi 5G band, if they support it, to reduce the stress factor on the 2.4G band
• Check your WiFi router to see if there is a MAC address limitation.
  • MAC address limitation is when your router is set/fixed to a maximum of 20 devices (or whatever it may have been configured for).
  • When you want to add the 21st device your router will deny access because you have filled up the 20 devices.
  • You need to clear or delete old devices that are not in use anymore. This may require someone with technical knowledge.
  • We advise that you don't have any MAC address limitations at all.
• Avoid bad extenders (Cheap ones are often not powerful enough to deal with or handle the kind of data required to transmit high quality audio).
  • With extenders, the connection between "router and extender" is decreased by 50%.  That said, your data will be even slower,. having to processes it while the speed is decreased.

There are more things you can do to optimize your WiFi router, but these above are the most common issues happening in users homes.

 

Normally, the InfinityLab power bank may be warm to the touch during discharging.  
However, if the power bank becomes too hot, starts to expand, or emits a strong odor, please stop using it immediately and contact our customer service. 

The connector between headphones and cable is Mini-XLR with lock mechanism. The connector that goes into sources is a combination plug, 3.5mm jack with 6.3mm adapter.

Normal: Trigger output is a standard 12VDC signal. Pulsed: Trigger output in a 12V pulse 50-100ms wide. Theatre: Turns the trigger on (standard 12VDC) only if the current input is in SSP mode, otherwise the trigger is off.

AURA supports network standards b/g for both AirPlay and Spotify Connect solution.

Citation speakers support 802.11g, 802.11n, and 802.11ac standards on both 2.4 GHz and 5 GHz bands. We recommend using 5 GHz if available, as this will give you more stable performance and use the full power of your wireless audio. Contact our customer support to get in touch with an expert that can help you with your Wi-Fi network. We are here to help!

In-wall speakers will work better for stereo listening because the speaker will be facing directly at you instead of above you. Note: Stereo imaging requires the listening position (“sweet spot”) to be dead center, equal distance, from the front left and right speakers.

Getting started with the checklist

• A JBL LINK device(s).
• Latest version of the Google Home app installed on your mobile device.
• Latest version of the Google app  (Android only) installed on your mobile device.
• A Google Account (you can create one online via Google).
• A mobile device with either iOS or Android support.
  • ​Must have iOS 10 or higher
  • Must have Android 5.0 and higher
  • There is no support for PC set up.
• An internet connection from your local ISP (Internet Service Provider).
• Your Wireless Network must secured with WPA2 Encryption (Enterprise mode NOT supported). 
• Availability and performance of certain features, services and applications are device- and network-dependent and may not be available in all areas; subscription(s) may be required, and additional terms, conditions and/or charges may apply.

Wi-Fi requirement

• Wi-Fi routers must have Encryption enabled to install JBL LINK speakers (WPA2 etc).
• Wi-Fi Extenders need to feature support of Multicast forwarding and UPnP.
• Always use 5 GHz Wi-Fi for best performance and less interference.
• For routers that have 2.4G Wi-Fi support only, make sure that they are using channels 1, 6 or 11 only.

You can now install your JBL LINK speaker to your Wireless Network and you can find our setup article that shows how to install your LINK product.

 

JBL QuantumSPHERE 360 is JBL QuantumSURROUND that’s kicked up a notch by using a head-tracking sensor to fix sounds in 360 degrees of space around you. With typical headphones, when you move your head, the soundscape follows your movement. But with JBL QuantumSPHERE 360, if you rotate your head, the sound source’s perceived location stays in place because the head-tracking sensor compensates for your head movement. For example, if there’s a sound coming from in front of you, and you turn your head to the left, the sound source’s perceived location moves to your right ear—the sound stays locked in space as you move your head. 

Also, the human brain uses small head movements to distinguish if sound sources are behind or in front of us. The brain processes the differences between when a sound arrives at the left vs. the right ear to determine where the sound is located. So with JBL QuantumSPHERE 360, you can move your head naturally to pinpoint the exact source of sounds around you. 

Alarm sound function in Bluetooth connectivity is not supported in iOS devices, however it is supported in Android devices.

The Normal and Pulsed DC triggers are active (on) when the No. 523 and No. 526 is on, they are not active (off) when the No. 523 and No. 526 is off. The Theatre DC trigger is present only if the current input is in SSP mode, otherwise this trigger is off.

First try using a different flash drive, we recommend the following: ScanDisk PNY Kingston Verbatim If the problem persists try using an updated version of Winzip when downloading the zip file to the USB flash drive.

Yes, when changing volume to higher or lower, the LED will illuminate to show that you are changing the volume.