How To
How To
1867 results
-
The led indicator will be solid blue.Was this helpful? Thank you for your feedback!
-
When the speaker is switching quickly between music sources via Bluetooth, it's normal to experience a very short 'pop' sound because the Bluetooth signal is breaking in and doing the handshake with the speaker. It won't appear after the Bluetooth signal is stable.Was this helpful? Thank you for your feedback!
-
Please note that the LFE Trim function is only active with surround source signals that feature a separate LFE track for the subwoofer. It does not affect subwoofer level when playing stereo or mono.Was this helpful? Thank you for your feedback!
-
When out in the world, on the beach, in a park, etc., the ALEXA feature will not work because the unit will not be connected to the internet via wi-fi. You can connect it to a wi-fi hotspot on a phone, if you like, or you can use it as a portable Bluetooth speaker.Was this helpful? Thank you for your feedback!
-
This problem is usually caused by pressing down too hard on the soundbar's VOL + or VOL - Buttons. Only press just enough for one click to be felt. If a second click is felt in the button, you are pressing too hard, and you are actually activating the MUTE function for learning, not VOL up or down. You may have to repeatedly let go of the VOL button on the soundbar, followed by pressing it again and then pressing the VOL button on the TV remote before the surround light on the soundbar lights up white and goes back to amber flashing, as a sign that this function has been learned. This is no problem, though. Just keep trying until the three commands have been learned. The soundbar only exits learning mode when you press and hold the surround button as the final step.Was this helpful? Thank you for your feedback!
-
• Please check whether your head unit Bluetooth support EDR (Enhanced Data Rate) • If the head unit does not support EDR this will cause the transfer data rate to be low and will impact the audio quality.Was this helpful? Thank you for your feedback!
-
The PartyBoost feature is not available when your JBL speaker is connected to a computer via Bluetooth. This is a technical limitation. When connected to a computer, the computer is acting as the primary device. Therefore, the JBL speaker does not have control of re-transmitting the Bluetooth signal to other JBL speakers.
NOTE: Speakers effected by this are the JBL Flip 5, JBL Flip 6, JBL Charge 5, JBL Pulse 4, JBL Xtreme 3, and JBL Boombox 2, as well as all future products featuring the PartyBoost feature.Was this helpful? Thank you for your feedback! -
The rechargeable AAA cells may of course be worn out, or they may not be installed at all. If this is the case, either insert the cells, or you can order new cells as original spare parts. Please contact Harman Helpdesk for your country, or the distributor for your country, for further info about how to buy new cells. Please note that the cells MUST be compatible with charging contact for the minus pole located on the side of the cell. Normal cells will not work. This is clearly mentioned in the owner's manual, and shown with a drawing. If you have purchased new cells with plastic coating along the length of the cell, it may be possible to peel off the coating by cutting gently with a knife, then peeling it off. Only about 1 cm needs to be open to the metal, closest to the flat end, for contact to be possible. Please note that the ear pads on K 912 are removed by simply grabbing the plastic plate that holds the ear pad, and pulling it away from the ear pod. There is one battery in each ear pod. For K 915, never just pull the pad away, since the locking claws are released by being rotated away from their locked position.. Both batteries are under the right-hand pad, and there is a silk-screened instruction on the top of the pod, showing that you must rotate the pad plate just a few mm counter-clockwise to unlock it.Was this helpful? Thank you for your feedback!
-
The wireless charge receiver in the smartphone may not be adequately coupled to the wireless charging transmitter on Smartbase. Re-adjust your smart phone’s position on the wireless charge arm.Was this helpful? Thank you for your feedback!
-
To set up the Harman Kardon Adapt in the HK Controller app, you have to select "One speaker", not the Adapt+ option. When selecting "One speaker", simply follow the on-screen instructions to install your Adapt on the Wi-Fi network. Note that the instructions for Adapt devices will appear on your screen after 30-45 seconds (Only Apple devices).Was this helpful? Thank you for your feedback!
-
Yes it will.Was this helpful? Thank you for your feedback!
-
If you only hear sound from one speaker in an MRM group, skip to the next song. After this, both speakers should play music correctly. You can then go back to the first song or continue playing where you left off.
Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call Us now at:
(877) 871-6755
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat with Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)