Please check the picture settings on your cable box, particularly the aspect ratio settings, which will vary depending on the brand and model of your cable box and on your local cable provider. You may wish to consult with your cable provider for more information on how to adjust the cable box's settings. Some settings, such as a setting to force an analog channel's native 4:3 aspect ratio to 16:9 widescreen to fit your display, may interfere with the cable system's copy-protection feature and cause distortion.

This is caused by the volume synchronizaton system in the iPad. When you switch off the iPad with click sounds activated, it sends the click sound to the Go+Play, also ordering the Go+Play to increase volume to maximum. The hiss is a result of the Go+Play Wireless being at full volume. As soon as you re-start your music playing from the iPad, volume is back to normal music use. If you do not switch the iPad on again, the Go+Play goes into standby after a few minutes, and the hiss disappears. You can prevent this problem by de-activating the click/alarm sounds on the iPad.

Some vehicles don’t provide an isolated ground for the head unit which may introduce noise. Please connect your smartphone to JBL DRG and enable the “Aux Noise Cancel” button in the App. This can be found right after Aux Line option in Connection Mode section.

Some head units in the vehicles use isolated grand, if JBL DRG use isolated grand as well, this will disable the chips inside DRG. Please connect your smartphone with JBL DRG and disable the “Aux Noise Cancel” button in the Apps right after Aux Line option in Connection Mode section.

What you are experiencing is normal. The Focus 700 is actually the Focus 500 headphone but with the added bonus of a charging case.

What you are experiencing is normal. The Inspire 700 is actually the Inspire 500 headphone but with the added bonus of a charging case.

Please press the round POWER Button on the FLIP again for 3 seconds, until the light in the button flashes blue/red. This will deactivate any active BT connection in the FLIP, and it should now become visible in the list of BT components on your smartphone or tablet. Pairing is now possible.

The order of tracks and folders on your USB stick will not be listed in alphabetical order. The sequence of the tracks or folders will be listed based on the number and types of tracks in the folders.

JBL LINK 10 and LINK 20 has 32 volume steps, and LINK 300 and LINK 500 has 48 volume steps. For broader volume changes, hold down either the volume + or - butons. Use individual presses for fine volume adjustments.

The volume level of the speaker is depends on the level of the source file itself. Some Dolby Atmos Music tracks are made to be quieter, and some louder.

When a connected Bluetooth device goes out of range, the JBL Micro Wireless will try to reconnect to it for 3 minutes. After 3 minutes the Micro Wireless can connect to other Bluetooth devices again.

Yes, after half an hour of inactivity, and provided Bluetooth pairing has been interrupted, Aura goes into full Standby. Now the wi-fi control light will no longer blink.

This is not an error. The App links to the Harman Kardon website when the "?" Button is tapped. User can then search the Quick Start Guide or Owner's Manual on the website.

In Bluetooth, there may be a small difference between the telephone (source) and the JBL Control X wireless unit. This means that they are not using the same scale. In any case, the difference will remain within one audio step on the phone or speaker.

Soundshift only works for the Boost TV itself, and cannot stop the other JBL Connect device. To stop the second device, press the JBL Connect button on your remote or device and they will disconnect.

If you see this message, you must download the Device Utility app from the Google Play Store. Follow the instructions in the app to activate your speaker, and then return to the Google Home app to complete the setup.
 

This is addressed in the owner's manual. After associating a group of four speakers, when deciding to go back to normal operation as two pairs, it is recommended to reset them to factory default settings, which requires associating speaker pairs again.

JBL Connect feature is using Bluetooth technology, so it is hard to say how far you can walk away. Depending on what other signals you have at your place that could interupt and wall material between speakers.

JBL Connect feature is using Bluetooth technology, so it is hard to say how far you can walk away. Depending on what other signals you have at your place that could interupt and wall material between speakers.

The source device may need to be in Standby, not just stopped, for the Soundbar to go into Standby mode using the optical or coaxial inputs.

If the network does not appear, you can manually type in the network name (SSID) and password to connect.
 

You can manually type in the network name (SSID) and password to connect if the network does not appear.

When you have associated two pairs of speakers, the range between primary and secondary speakers (all 3 speakers), will be maximum 10 meters. The range will increase if you only use one pair of speakers (30 meters). We recommend placing the speakers on a high-level surface or shelf, for best possible connection.

When using the JBL One app to control USB audio playback, please wait more than 1 second in between button presses.

You should hear the audible voice stating ‘low battery’ when you have about 20 minutes left of battery life left on the UA WIRELESS headphones. If you have an Apple device, you will actually be able to see the battery life in the upper right hand corner of the device next to the BT symbol.

If there is no activity on your JBL Boost TV, it will go into standby mode after 20 minutes, and will take a couple of seconds to turn on after standby mode.

If there is no activity on your JBL SB 250, it will go into standby mode after 20 minutes, and will take a couple of seconds to turn on after standby mode.

NOTE:  LINK speakers must be set up on a WiFi network before Bluetooth can be activated. Once it is set up, you can use Bluetooth anywhere (Unless you reset the speaker and start all over with installation).

Pairing issues with a Smartphone or Tablet:

1. First try to restart the Bluetooth connection on your source device (Smartphone/tablet) by switching Bluetooth off and on again with a short pause in between.
2. Forget previous paired connection (on your smartphone/tablet) in your Bluetooth settings if you once had paired with our product.
3. Try to restart source device(Smartphone/tablet) by powering it off and on again, and after restart try to establish a Bluetooth connection to your JBL LINK device.
4. If above does not work, then try to restart your JBL LINK device by turning it off and on again.
5. Press and hold down the Bluetooth button on your JBL LINK device to initiate pairing mode again.
6. Go into Bluetooth settings on your Smartphone/tablet.
7. Perform a restart or reset if you are not able to connect after above steps.

Back to helpful articles --> Articles overview

JBL LINK Bluetooth specifications:

• Bluetooth version 4.2
• A2DP v1.3 with SBC Audio Codec.
• AVRCP v1.5

There are multiple ways to check your heart rate (HR) while using your headphones both in and out of workouts. On the UA Record mobile app select the UA Sync icon in the upper right hand corner of the dashboard. If your headphones are connected, they will appear under "My Apps and Devices". Tap on "UA Sport Wireless Heart Rate" and you will see your headphones settings. Your current heart rate will appear under the headphones' image. You will hear your heart rate when using the headphones during a UA Record workout with audio coaching. While using with your UA Band during a workout your HR will be shown with your workout stats and will coordinate with the HR zone LED on the Band. You also can simply tap the UA logo on the RIGHT ear bud to hear the audible voice stating your heart rate reading.

At the bottom of your Horizon alarm clock, you will see a little cap where the backup-battery resides. Turn the cover lid left to open it, and on the back of the cover lid, you will see the serial number.

There are threaded inserts for mounting screws in the bottom of the Omni 10+ and Omni 20+. Mounting accessories are not available via Harman Kardon. For Omni 10+ there are two mounting screw holes which are 3mm in diameter and 67mm apart. For Omni 20+ there are two mounting screw holes which are 3mm in diameter and 110,5mm apart.

In Amazon's app called Alexa. There you can set, change and login with your favorite supported music service. They offer Amazon Music, Spotify, Pandora and much more. Go to settings in the Alexa app, select "Music & Media.

You can view stats from your past workouts by going to your dashboard and tapping the Fitness quadrant. Tap the workout you would like to view. Your average and peak heart rate, heart rate distribution through your training session, and a graph of your real-time heart rate, will all be shown.

For headphones with version 4.0 of the firmware, updates will be available via jbl.com/app. For headphones with firmware version 5.0 or higher, update notification will be pushed via the app

Subwoofer placement is an art in itself. You will hear two different statements about the positioning of a sub. You will hear people say that it doesn't matter where you put the sub, you can put it anywhere in a room. You will also hear people say that placement is very critical. It sounds like these two statements contradict each other. Believe it or not, they don't. It is generally believed by most audio authorities that low frequencies (below 125Hz) are non-directional, and therefore, placement of a subwoofer within any listening room is not critical. While in theory it is true that the larger wavelengths of very low frequencies are basically non-directional, the fact is that when installing a subwoofer within the limited confines of a room, reflections, standing waves and absorptions generated within the room will strongly influence the performance of any subwoofer system. As a result, specific location of the subwoofer becomes important, and we strongly recommend that you experiment with placement before choosing a final location. Placing it in a corner is often times the most effective spot.

The sensor is located in the LEFT ear bud. The left enhancer will feature a cut out for the sensor and should be fully exposed.

The heart rate sensor is located inside the RIGHT earbud inside the sound tunnel. If the Heart Rate detection is activated and you remove the RIGHT earbud, the audio voice will notify you to insert the ear bud and will recalibrate once it is detected again.

Behind the speaker grill, at six o'clock, two cm. from the bottom.

The microphone is located on the remote small hole on the right side

Under the little hole next to the phone reciever button.

On the BT and ELITE NXT series over-ear and on-ear models, the serial number sticker is on the inside of the headband left side, visible when the size adjustment is pulled all the way out. Serial numbers are also shown on the boxes. On ELITE 100 in-ear, it is on the box only.

The Serial Number is located on the strap hook (see image below), it may be necessary to remove the strap to see it clearly.

It is a tiny white sticker, located on the inside of the left-hand size adjustment slider on E35.

The soundbar support SBC codec.

Our LINK BAR supports the following:
MP3, AAC-LC, HE+ACC, FLAC, Vorbis, Wav, CELT/opus via Wi-Fi streaming, and with Bluetooth SBC and AAC.

The Harman Kardon Aura Studio 2 features: Bluetooth v.4.1 A2DP v.1.3 AVRCP v.1.5

C-Media 6632A Processor

JBL Charge 3 is available in 5 fashionable finishes: Teal, Gray, Black, Blue and Red.

For OMNI BAR+, three sources are available: HDMI (not applicable for ADAPT+), Optical or AUX input. For Adapt+ two sources are available: Optical in/outputs and Analog in/outputs. If you select "Watching movies and TV shows" in the HK controller app for either one of them, you will have a very little delay and good lip sync with the TV for video applications. However, you will not be able to rebroadcast the TV signal to other OMNI+ speakers when selecting this mode. If you select "Listening to music", you will be able to rebroadcast TV signal to other OMNI+ speakers in your house, however, you will have lip sync delay with video material. Select that specific mode if you use HDMI (not applicable for ADAPT+), Optical or AUX for music only. Using Chromecast, Spotify Connect or Bluetooth is not part of these modes. When using one of these streaming methods, you are able to rebroadcast any music source.

Connecting a USB stick

1. You can enjoy music from your USB Stick directly into the Partybox device.
2. Insert the Stick into theport, located on the back of your Partybox.
3. The USB Stick has to be formatted FAT16 or FAT 32 and supports MP3, WAVE and WMA Music files.
4. It will start automatically playing the content on your USB stick.

AUX Connection

1. You can connect any devices through the analog connection
2. Use an analog cable (Not included in the box) and connect your device.
3. Press play on your external device and enjoy the music!

RCA Connection (*Partybox 200/300/1000 Only)

1. The Partybox features both Input and Output RCA connection.
2. Connect your RCA cable (not included) to either one of the ports.
3. You can use it with your DVD/BlueRay player or AVR system.

Guitar and Microphone

1. Connect your to the dedicated port or connect your electric   to the
2. You can mix sound or make your own karaoke party with your Partybox.
3. Sing or play through your devices.
   1. To adjust the volume of the audio source, press volume+ or volume- buttons.
   2. To adjust the volume of the microphone or guitar, rotate the or

 

Charging external devices

1. Whenever your mobile device needs some extra power, the Partybox can help you!
2. Featuring a USB Charging port for both Music (USB on a stick) or when you need to charge your device.
3. Simply connect your device to the port and start charging.
   1. NOTE: The Partybox 200 needs to be connected to AC power all the time to charge or function as a speaker.
   2. The Party 300/310 has a battery and can charge any device without needing AC power (unless the product's battery is depleted then you need to recharge via AC power).

There are many ways to enjoy your JBL Partybox On-The-Go, 100, 200, 300, 310 & 1000. The options are endless and you are in control of the party

The N90Q can process these formats through the digital input: - 2-channel - Sample Rate: 44.1K / 48KHz / 96KHz - Bit Resolution: 16 bit / 24 bit

Enchant series information

The Enchant series is not only a beautifully designed speaker, but it also delivers the sound to a completely new level.
Always wanted to have Surround Sound, but never wanted extra speakers, with the MultiBeam feature you can get Surround Sound experience right at your fingertips.

Enchant 1300 for Bigger rooms

1. Perfect for bigger rooms that requires a bit more sound and punch when watching or listening to music!
2. Powerful sound with 13 Channels in one speaker with a maximum of 240W

2. Features MultiBeam technology for Surround Sound experience.
3. 4K HDR10 compatible on both HDMI Inputs and output (ARC).
4. HDCP 2.2 Compatible
5. Google Cast built-in, stream your favorite music through your Wi-Fi connection.
6. Bluetooth 4.2 technology for easy streaming with any of your mobile devices.
7. And much more!

Enchant 800 for Smaller rooms

1. Perfect for smaller rooms to extend the sound performance in any situation.
2. Powerful sound with 8 Channels in one speaker with a maximum of 180W

2. Smaller in size compared to Enchant 1300, but just as an amazing sound.
3. Features MultiBeam technology for Surround Sound experience.
4. 4K HDR10 compatible on both HDMI Input and output (ARC).
5. HDCP 2.2 Compatible
6. Google Cast built-in, stream your favorite music through your Wi-Fi connection.
7. Bluetooth 4.2 technology for easy streaming with any of your mobile devices.
8. And much more!

WMA Losless and WMA PRO cannot be decoded.

Model HTFS 2 is used for the satellite speakers in these two BDS systems. There is no floor stand for the center speaker in the 635 system.

The BDS system supports a variety of audio and video formats. Listing all disc, surround and codec formats is beyond the scope of an FAQ. Please donwload the Owner's Manual from the harman.com website for a full list.

All of our in-wall/in-ceiling speakers are designed to be used in a wall without the need for a back-box. The specs provided are based on no back-box. However, when adding a back-box (really only possible when doing new construction), you will improve the low frequency response a bit, getting a tighter bass response.

JBL Xtreme, JBL Pulse 2, JBL Charge3, JBL Flip 3, Pulse 3, and Flip 4 Android, Google Now, Google Play are trademarks of Google Inc. Siri, iTunes, and Apple Music are trademarks of Apple Inc. Spotify is a registered trademark of Spotify AB. IOS is a registered trademark of Cisco in the US and is used by Apple under license.

The first JBL speakers featuring the JBL Connect technology are: JBL Flip 3, JBL Pulse 2, JBL Xtreme, JBL Boost TV and JBL Charge 3, SB 450 A firmware upgrade is available for the JBL Charge 3 ,which will upgrade Connect to JBL Connect+. After this fw upgrade, it is no longer possible to connect the Charge 3 with other products which have JBL Connect ( Flip 3, Boost TV, Pulse 2, Xtreme )

NOTES

• Only file names that contain numbers or English characters can be displayed, otherwise “UNKNOWN” will be displayed.
• “UNSUPPORTED” is displayed when the file format is not supported.
• Do not extract the USB device while in operation.
• For a large capacity USB, it may take longer than a few minutes to be searched. USB with more than 2000 files cannot be supported.
• Devices which require additional program installation connected to a computer are not supported.
• The USB port of the soundbar cannot be connected to a computer and it cannot be used as a storage device.
• The exFAT and NTFS file system is not supported. FAT16/FAT32 systems are available.
• Depending on some devices, it may not be available to recognize the followings on the soundbar: External HDD; Card readers; Locked devices; Hard type USB devices; USB hub; Using USB extension cable; iPhone/iPod/iPad; Android device.