How To
How To
1867 results
-
To pair to a different device, double tap and hold your finger on the JBL logo for 5 seconds until you see the LED light flash blue. Make sure that the device you are trying to connect to is in range and in pairing mode. You should see the Endurance headphone pop up on your discoverable devices within a few seconds and the flashing LED light should now be a solid blue.Was this helpful? Thank you for your feedback!
-
Power on the Soundgear and press and hold the Bluetooth located next to the power button on the right arm. Once you press the the bluetooth button, you will see a fast blinking LED light as it attempts to pair to a different device. You will also hear the audible chime as it attempts to Make sure the device you are attempting to connect to is on and in pairing mode. The JBL Soundgear should be displayed on your discoverable devices within a few seconds. Choose the JBL Soundgear and you should now be connected!Was this helpful? Thank you for your feedback!
-
In order to pair to a different device, make sure the headphones are turned off. Proceed to press and hold the power button located on the LEFT arm of the neckband. You will hear the audio voice prompt state, “powering on” Continue to press and hold the power button for 3-5 seconds or until you hear the voice prompt state, “looking for device.” Make sure that the device you are attempting to connect to is in the Bluetooth search mode and within range. UA | JBL Flex should appear on your device within 3-8 seconds. Once you choose this option on your discoverable devices, it will connect and the voice prompt will state “Connected”Was this helpful? Thank you for your feedback!
-
On the Right ear cup, slide the bluetooth button towards the down position and hold until you see the fast blinking blue LED light. Make sure that the device that you are trying to connect to is in pairing mode. It should recognize the N60NC Wireless within a few seconds. You should here the audio "chime" when it is connected and the LED should change to a slow blinking light.Was this helpful? Thank you for your feedback!
-
1. Place the 3770 in Bluetooth input mode with the BT button on the front panel or the remote. 2. Do a BT search on the phone, until you find HK3770. Then pair with it. 3. Now you can select the HK3770 as audio source on your phone, depending on the phone. On some phones, you can simply begin to play music after performing the pairing, and the HK3770 will play, if it is in Bluetooth input mode, shown on the front panel display. 4. You can control play/pause etc. from either your phone or from the HK3770 remote control. If you want to use the HK3770 remote, you must first press the STEREO Button on the remote control in order to activate the correct remote codes. Now a press on the PAUSE Button on the HK3770 remote will pause the music by placing your phone on pause, and you can restart play by pressing the PLAY Button. 5. To pair another source to HK3770, first deactivate BT on the source presently paired to release new pairing.Was this helpful? Thank you for your feedback!
-
Press and hold the center button on the inline microphone located below the right earpiece. It helps to have one of the ear inserts in your ear to listen to the audible voice prompts. If this is your first time using the headphones, the headphones will automatically go into search mode. You will hear the audible voice stating, “power on” followed by “looking for device”. To power off, press and hold the center button on the inline microphone until you hear the audible voice stating, “power off.” The flashing LED light should change to a solid red light before completely turning off.Was this helpful? Thank you for your feedback!
-
Press and hold the center button on the inline microphone located below the right earpiece. It helps to have one of the ear inserts in your ear to listen to the audible voice prompts. If this is your first time using the headphones, the headphones will automatically go into search mode. You will hear the audible voice stating, “power on” followed by “looking for device”. To power off, press and hold the center button on the inline microphone until you hear the audible voice stating, “power off.” The flashing LED light should change to a solid red light before completely turning off.
Was this helpful? Thank you for your feedback! -
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.Was this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure the E65BTNC headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.Was this helpful? Thank you for your feedback!
-
Press and hold the center button located on the inline microphone. It helps to have one or both ear inserts in the ear to hear the audio voice prompts. Once you press and hold the power button, you will hear the audio voice stating, "powering on". If this is your first time pairing the device, it will automatically go into pairing mode and will be looking for the device. Make sure the device you are trying to connect to is in search mode. It should recognize the Everest 110 within 2-3 seconds. If you would like to connect to a different device. Make sure the unit is off and proceed to press and hold the center button on the inline mic from 4-6 seconds until you hear "powering on......JBL Everest is ready to pair. Go to the pairing menu on your device" You will now be able to pair to a different device. The device should recognize the Everest 110 within 2-3 seconds and will connect.Was this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.Was this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call Us now at:
(877) 871-6755
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat with Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)