How To

Support Overview / How To

How To

1867 results
  • How do I reset the device to factory settings?
    Power ON the device, then press and hold the "Volume+" and the "Play/Pause" buttons at the same time. When the device switches off after a few seconds, sounding the OFF prompt, it has been reset.
  • How do I reset the Endurance Series Headphones?

    For all models except Endurance Peak:
    Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
    Note that resetting the Dive will not erase music contained in the MP3 memory.

    Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.

    Endurance Run 2 Wireless reset: Disconnect the earbuds from the paired source device and then press and hold the volume(+) & volume(-) buttons simultaneously for 5 seconds. 

  • How do I reset this unit back to factory settings?
    1. Turn the unit ON.
    2. Press and hold the VOLUME + and PLAY/PAUSE buttons at the same time for more than 5 seconds.
    3. Unit is now reset.
  • How do I reset to factory defaults?
    Press Phone and "volume +" > 2 sec. Power must be on.
  • How do I see that battery is low?
    The charging LED on the headset will flash red when the battery is low. For the ELITE models, a more accurate indication of remaining battery time can be seen on the fuel gauge in the app.
  • How do I see that the headphone is fully charged?
    The red light in the charging status LED on the right cup will turn off.
  • How do I see what is left and right on the AKG N20?
    The L and R that indicate the two channels are located on the soft grommets that protects the signal cable where it enters the headphone shell. The letters are recessed into the grommets, and are very small. If they are too difficult to read, it may be easier to simply observe how the headphones are situated in the ears. The oval body of each in-ear, with the chrome stripe, should be away from the head, and be situated in the ear lobe, not stick out directly from the head.
  • How do I see when charging is complete?
    The red light in the control LED goes out when charging is complete.
  • How do I see when my JBL E45BT or E55BT is fully charged?
    While charging, the charging indicator diode is lighting constantly. When charging is complete, the light goes out.
  • How do I see when the noise cancelling battery of AKG N20NC is empty?
    When less than one hour's capacity is left, the red diode will blink. It will eventually stop blinking, when all power is gone.
  • How do I set up my Adapt so my existing equipment can play stereo?
    In the Harman Kardon Controller app, set up the Adapt as a stand-alone room, not a stereo pair room. The Adapt always delivers stereo audio via its Audio Out jack.
  • How do I setup my AVR's Zone II?
    At the bottom of the Setup Source page for the specific source you are setting up you will find a field labeled Zone II Input or Zone II Audio Input. This is where you will assign the analog audio input that you will use for this particular source. The Zone II audio is strictly analog. So, for example, if you are planning to use your DVD player for the main room and Zone II, you will need to connect the DVD player to the AVR using both analog and digital connections, digital for the main room, and analog for Zone II.
< 1 ... 59 60 61 62 63 ... 156 >

Can’t find what you’re looking for?

Call Us

Call Us

Talk to a product expert
Call Us now at: (877) 871-6755

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)

Chat with Us

Chat with Us

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)

message

Text Us

Text with a support agent via SMS at:
628-333-7807

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)