How To
How To
1867 results
-
Use a clean cotton swab slightly moistened with alcohol to:- Remove earwax and dirt from the ear tips on your earbuds.
- Clean the charging pads and ports on your earbuds and in the charging case respectively. Then use a dry and soft cotton to rub down the dust and lint.
- Clean the grooves on the cover and at the bottom of the charging case.
TIP: We recommend that you repeat this operation every few weeks or so to keep your headphones clean and to not affect the charging speed and quality.Was this helpful? Thank you for your feedback! -
So your Pulse 4 got dirt on it, or even fingerprints, and you want to show off the device the best way possible.
Keep reading this article, and we will instruct you on how to clean the glass and device.
How to clean your speaker- Dirt and stains on your speaker can be cleaned under lukewarm running tap water.
- Use a soft cloth, preferably cotton, to clean the glass and to remove fingerprints. Hold the top part to avoid adding more prints to the glass part.
Contact our Customer support for more help and advice to keep your speaker top-notch!
Was this helpful? Thank you for your feedback! -
To clean your headphones, please follow the instructions below:
- Clean earpads and headphones with a soft, slightly damped cloth.
- Do not soak, submerge or allow moisture to enter near drivers and cable jacks.
- Earpads and cables can be purchased if worn out at www.Marklevinson.com.
- Use a polishing cloth to wipe down after use to remove fingerprints etc.
Was this helpful? Thank you for your feedback! -
To find out the software version, press and hold the [VOL- ] and [SOURCE] buttons simultaneously. The software version will scroll across the front display.
Was this helpful? Thank you for your feedback! -
To check the firmware version:
Press and hold the 'Preset 1' & 'Preset 5' buttons for more than 10 seconds.Was this helpful? Thank you for your feedback! -
The battery is charged using an included USB-A to USB-C USB fabric cable. It will be fully charged for 2 hrs. Note, this cable is only for charging the battery, it will not deliver audio.Was this helpful? Thank you for your feedback!
-
To charge, plug in the USB-C Connector and connect to a USB-C port (or USB-A port using the included adaptor).
Please note: you cannot listen while charging.
Was this helpful? Thank you for your feedback! -
To deliver 65W PD charging to your laptop, you will need a USB-C to USB-C cable supporting minimal 3A current.
To deliver 100W PD charging to your laptop, you will need a USB-C to USB-C cable supporting with E-Mark and supporting 5A current.Was this helpful? Thank you for your feedback! -
To enjoy the wireless charging feature for your InfinityLab power bank, below are the instructions on how to activate it.
- Press the power button (located on the front side, next to the battery indicator).
- Place your device on top of the power bank.
- The LED indicator on the side of the power bank will light up, indicating that the product is "charging."
Was this helpful? Thank you for your feedback! -
The surround speakers of our JBL Bar 800 or Bar 1000 can be recharged through the USB-C connection, located on the side of the speaker. The speakers can be charged by docking them in the soundbar also.Was this helpful? Thank you for your feedback!
-
Ensure that your InfinityLab power bank is charged, then press the power button to trigger charging.
If nothing happens, please try to charge your power bank with a different charger and check the charging indicator next to the power button to see if the LEDs lights are blinking.
If it still doesn’t work, please contact our customer service team for help.Was this helpful? Thank you for your feedback! -
You might have to add a USB extension dock to get the JBL Quantum 350/600/800/810 dongle as close to the headset, or place the common sources of interference (e.g. routers, Wi-Fi speakers etc.) as far from the JBL Quantum 350/600/800/810 dongle.
Was this helpful? Thank you for your feedback! -
• Always have clear line of sight between your Bluetooth device (speaker, headphones etc.) and source device (Smartphone/tablet/PC etc). Be aware of obstacles in front of your devices.
• Try to shutdown other products that have Bluetooth, but are not being used. They are often the reason for interference even though they are not being used.
• Do not stand too close to your Wi-Fi router since a Wi-Fi signal is stronger and in many cases will "overlap" the connection.
• Be aware of walls around you. Concrete and brick walls will often interrupt the signal, as it cannot pass through such thick walls.
• Bluetooth signals cannot travel through water, which includes the human body. Make sure with wireless headphones to keep your source device and the receiver on the same side of your body.
• Open spaces such as parks can cause issues for your devices, as open air is "bad" for any Bluetooth signal if it cannot reflect from objects around you.Was this helpful? Thank you for your feedback! -
In the Google Home app, go to device settings and set up your home address again. The home address is where the Oasis sets its time zone. If changes are made, it may be necessary to reboot the speaker. Remove and reinsert the power cable to ensure that the changes take effect.
Was this helpful? Thank you for your feedback! -
With both detachable surround speakers undocked, you can select the surround sound level by pressing the REAR button on the remote control.Was this helpful? Thank you for your feedback!
-
You can adjust the amount of audio coming from the upfiring speakers by pressing the "ATMOS" button on the Remote control and switch between middle (default), high or low.Was this helpful? Thank you for your feedback!
-
Sometimes you need to change settings such as changing EQ to match the content you are watching or adjusting the bass level.
- Grab your Remote control.
- Press and hold the "HOME" button down, an overlay on the right side of the screen will appear.
- This is our quick settings menu.
- Go to Settings --> Sound --> Select EQ Mode
- Hit the back button Arrow icon a couple of times until you are back at what you are watching.
Was this helpful? Thank you for your feedback! -
The InfinityLAB charger has "smart power distribution" feature, it's smart enough to know how to allocate power, depending on which devices are plugged in.
Take 65W charger as an example:
If plug in only 1 USB-C device to this charger, the USB-C port can deliver max. 65W PD fast charging.
If plug in one USB-C device and one USB-A device simultaneously to this charger, the USB-A port can deliver max.15W fast charging, and the USB-C port can deliver max. 45W PD fast charging.
Was this helpful? Thank you for your feedback! -
JBL Quantum 400 and ONE are compatible with USB C to A cable to enjoy PS4 console with RGB Lighting on, and Quantum 600 and 800 with wireless-enabled by USB dongle also gives lighting moment on PS4 console games.
*NOTE that RGB will not light up when connecting with 3.5mm cable to any device (PC, Console, Mobile, etc.) because the cable doesn't have power enough for the RBG lighting.Was this helpful? Thank you for your feedback! -
The speaker uses 4 x 15W when running on battery. You will hear a slight lower bass performance, compared to being connected to AC power.Was this helpful? Thank you for your feedback!
-
An OR300 weighs 42 g per earpiece.Was this helpful? Thank you for your feedback!
-
Up to 3 units can connect with the party mode.Was this helpful? Thank you for your feedback!
-
You can stream to two speakers simutanouisly with the Connect function.Was this helpful? Thank you for your feedback!
-
Up to 2 source devices can connected at the same time.Was this helpful? Thank you for your feedback!
-
You can connect 2 smart devices ( iOS or Android ) simultaneously by Bluetooth. One when connecting via AUX cable.Was this helpful? Thank you for your feedback!
-
You can connect 3 smart devices ( iOS or Android ) simultaneously by Bluetooth. One when connecting via AUX cable.Was this helpful? Thank you for your feedback!
-
Three devices can be connected to Go + Play BT/Wireless at the same time. You can easily take turns when playing music from 3 connected devices by pressing play on one of them. If you press play on the second of the connected devices, the first one will be interrupted and the second will start playing, and so on. If you want to connect a 4th device, you'll be required to disconnect one of the connected devices first.Was this helpful? Thank you for your feedback!
-
If no fans or Air Conditioning are being used to cool the No. 536 amplifiers there should be 2U rack spaces vertically between No. 536 amplifiersWas this helpful? Thank you for your feedback!
-
You should expect up to 8 hours of playback time on a fully charged battery.Was this helpful? Thank you for your feedback!
-
You should receive up 10 hours of audio playback. (varies by volume level and audio content)Was this helpful? Thank you for your feedback!
-
The Everest 110 should receive 8 hours of audio playback on a full charge. However, depending on the volume level at which you listen to your music at, this can decrease the battery life faster.Was this helpful? Thank you for your feedback!
-
Up to four headsets can play simultaneously. For each additional headset, hold the pairing buttons on both transmitter and headset for 5 seconds, then release. Now switch the transmitter off and on again with the pairing button, and the connection is active.Was this helpful? Thank you for your feedback!
-
The BDS -75 and -77 models support 2000 files and 10 folder levels on DLNA.Was this helpful? Thank you for your feedback!
-
The Vi Personal Trainer is pre-fitted with the size small fin and comes with two additional fin sizes. To get accurate ratings on your heart rate, you'll want to find the fin that fits most comfortably. The Vi also comes pre-fitted with the size medium ear tip and comes with four additional tip sizes. (XS, S, M, L)Was this helpful? Thank you for your feedback!
-
The N40 comes with 4 sizes in the packaging. (XS, S, M, L)Was this helpful? Thank you for your feedback!
-
The N20LT features 4 ear tip sizes: X-S, Small, Medium, LargeWas this helpful? Thank you for your feedback!
-
The JBL Live 100 comes with 3 different ear tip sizes (S, M, L)Was this helpful? Thank you for your feedback!
-
The Duet Mini headphones come with three ear tip sizes. (Small, Medium, Large)Was this helpful? Thank you for your feedback!
-
The UA Sport Wireless Flex has size 3 (wingless) and the larger size 5 (winged). It also features three sizes of the small, medium, large inner ear tips. The unit comes with the size 5 Medium in ear tip on the unit out of the box.Was this helpful? Thank you for your feedback!
-
The E15 headphones come with three sizes of ear tips: S, M, L which accommodate most ear sizes.Was this helpful? Thank you for your feedback!
-
Our Multi-Connect feature supports up to two devices, to be connected at the same time. But only one device can play at a time.Was this helpful? Thank you for your feedback!
-
They support up to 8 paired devices without reset.Was this helpful? Thank you for your feedback!
-
Only one device at a time.Was this helpful? Thank you for your feedback!
-
The amount of Chromecast speakers you can stream music to depends on the bandwidth of your local wireless network. Theoretically, an unlimited amount of devices can be connected to stream the same song.Was this helpful? Thank you for your feedback!
-
As a stand-alone soundbar, the product can support 5.0.2 channels. When connected to the optional Citation Sub or Citation Sub-S, the product can support 5.1.2 channels.
It is also possible to have physical rear surround channels by connecting the optional Citation Surround.
Was this helpful? Thank you for your feedback! -
You can have several source paired, but only one active at the same time.Was this helpful? Thank you for your feedback!
-
Up to 3 devices can be paired to the BOOST TV at one time.Was this helpful? Thank you for your feedback!
-
All three devices supports up to 3 Bluetooth connections at the same time. However, only one can play music while connected, if one of the other paired devices starts playback, it will interrupt the music that is currently playing, and begin playing from the second or third connected device.Was this helpful? Thank you for your feedback!
-
You can have two connectecd devices at the same time.Was this helpful? Thank you for your feedback!
-
AURA Studio has the Multi-Connect feature (Social-Mode) which allows you to connect up to 2 devices at the same time and play different music from either device. Note that the music playing on one device will be interrupted when the other device begins playing music, and vice-versa.Was this helpful? Thank you for your feedback!
-
You can have 3 smart devices connected at the same time and by pressing play on either one of the sources (smart devices) will start streaming music. The speaker can remember up to 8 paired smart devices and when this buffer is full it will release the first added device in connected sequences. Resetting the speaker will also clear this buffer.Was this helpful? Thank you for your feedback!
-
If your OMNI 50+ is completely drained, it will take 3,5 to 4 hours to fully charge. We advise to charge the Omni 50+ when it starts to blink red.Was this helpful? Thank you for your feedback!
-
The cable is approximately 125 cm long.Was this helpful? Thank you for your feedback!
-
The memory is based on flash memory, and is not forgotten.Was this helpful? Thank you for your feedback!
-
Any conversation or search history is stored in the cloud via your Google account and is saved until you choose to delete it. JBL LINK speakers do not keep or store any data locally.Was this helpful? Thank you for your feedback!
-
The surround speaker takes up to 4 hours to fully charge.Was this helpful? Thank you for your feedback!
-
Approximately 2.5 hours. This depends on the actual charger used, and its capacity in Amperes.Was this helpful? Thank you for your feedback!
-
You can listen up to 8 hours of MP3 music, with a fully charged battery, depending on volume and type of musicWas this helpful? Thank you for your feedback!
-
When docked and connected to the harness, the BASSPRO GO can be used as a powered subwoofer or a full-range car audio speaker. It receives it’s audio source from the head unit via the wiring harness and it’s power from the car battery. Bluetooth is not active.
When undocked/portable and removed from the harness, it can no longer be used as a powered sub. It is strictly a full-range portable Bluetooth speaker system. It receives it’s audio source from the Bluetooth input only, and receives it’s power from the internal battery.
Was this helpful? Thank you for your feedback! -
For headphones with Version 4.0 of the Firmware, the first update will be done via USB cable, and after the first update, all subsequent updates will be delivered over the air. For headsets with version 5.0 of the firmware, all updates will be delivered over the air, via the appWas this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call Us now at:
(877) 871-6755
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat with Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)