How To

Support Overview / How To

How To

1867 results
  • How do I turn off the device?
    Press and hold the center button for 3-5 seconds until the audible voice states “power off” you will briefly see a red light before it completely powers down.
  • How do I turn off my internal TV speakers?
    Every TV is different, but most current TVs will let you turn off your internal TV speakers in the Settings menu under the Audio section.
  • How do I turn off my internal TV speakers?
    Every TV is different, but most current TVs will let you turn off your internal TV speakers in the Settings menu under the Audio section.
  • How do I turn off my E45BT or E55BT?
    The on/off button is a spring-loaded slider button. Press the button upwards against the spring pressure, and hold it there for about three seconds. Now you will hear the "off" prompt sound in the headphone speakers, and the LED light goes out. Now the headphones are switched off. Please note that if you do not play music or press any button for about 10 minutes, the headphones will switch off automatically.
  • How do I turn it on?
    Press and hold the power on/off symbol/button for 3 seconds.
  • How do I turn it on?
    Press the power on/off symbol/button down for 1 second.
  • How do I switch the enhancer sizes?
    The best way to remove the enhancer from the ear bud is to gently pull back the outer rim of the enhancer that is located around the base of the ear bud. When replacing the current enhancers with a different size, please make sure to align the funnel of the enhancer tip over the small speaker screen of the headphone casing. The LEFT enhancer will feature the square cut out that allows you to receive your Heart Rate reading. It is important that the small digital square on the ear bud is fully exposed and the enhancer cut out is placed around it and not over it. If the enhancer is not attached properly, you will hear the audible voice stating that it cannot receive an accurate reading on your heart rate and you will need to readjust the enhancer.
  • How do I start the product for the first time?

    The JBL product is in a deep sleep mode, which it is to prolong the lifetime of the battery. Connect the case to a charger for about 2 seconds to wake the product up and take the earbuds out from the case. Once you put the earbuds back in the case, it's ready to pair through Bluetooth. 

  • How do I skip tracks on the T205?
    Two quick clicks on the microphone will skip the track forward. Three quick clicks on the microphone will skip the track backward to the previous song.
  • How do I skip tracks on the Synchros E30?
    The track control button is located in the center of the inline microphone. This also serves as the pause/play button and enables you to answer and hang up phone calls. Two quick clicks on the center button will skip the tracks forward to the next song. Multiple quick clicks will skip the tracks backward. Compatibility may vary with some older phone models.
  • How do I skip tracks on the Everest 750NC?
    To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.
  • How do I skip tracks on the Everest 310/710 headphones?
    To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.
  • How do I setup my AVR's Zone II?
    At the bottom of the Setup Source page for the specific source you are setting up you will find a field labeled Zone II Input or Zone II Audio Input. This is where you will assign the analog audio input that you will use for this particular source. The Zone II audio is strictly analog. So, for example, if you are planning to use your DVD player for the main room and Zone II, you will need to connect the DVD player to the AVR using both analog and digital connections, digital for the main room, and analog for Zone II.
  • How do I set up my Adapt so my existing equipment can play stereo?
    In the Harman Kardon Controller app, set up the Adapt as a stand-alone room, not a stereo pair room. The Adapt always delivers stereo audio via its Audio Out jack.
  • How do I see when the noise cancelling battery of AKG N20NC is empty?
    When less than one hour's capacity is left, the red diode will blink. It will eventually stop blinking, when all power is gone.
  • How do I see when my JBL E45BT or E55BT is fully charged?
    While charging, the charging indicator diode is lighting constantly. When charging is complete, the light goes out.
  • How do I see when charging is complete?
    The red light in the control LED goes out when charging is complete.
  • How do I see what is left and right on the AKG N20?
    The L and R that indicate the two channels are located on the soft grommets that protects the signal cable where it enters the headphone shell. The letters are recessed into the grommets, and are very small. If they are too difficult to read, it may be easier to simply observe how the headphones are situated in the ears. The oval body of each in-ear, with the chrome stripe, should be away from the head, and be situated in the ear lobe, not stick out directly from the head.
  • How do I see that the headphone is fully charged?
    The red light in the charging status LED on the right cup will turn off.
  • How do I see that battery is low?
    The charging LED on the headset will flash red when the battery is low. For the ELITE models, a more accurate indication of remaining battery time can be seen on the fuel gauge in the app.
  • How do I reset to factory defaults?
    Press Phone and "volume +" > 2 sec. Power must be on.
  • How do I reset this unit back to factory settings?
    1. Turn the unit ON.
    2. Press and hold the VOLUME + and PLAY/PAUSE buttons at the same time for more than 5 seconds.
    3. Unit is now reset.
  • How do I reset the Endurance Series Headphones?

    For all models except Endurance Peak:
    Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
    Note that resetting the Dive will not erase music contained in the MP3 memory.

    Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.

    Endurance Run 2 Wireless reset: Disconnect the earbuds from the paired source device and then press and hold the volume(+) & volume(-) buttons simultaneously for 5 seconds. 

  • How do I reset the device to factory settings?
    Power ON the device, then press and hold the "Volume+" and the "Play/Pause" buttons at the same time. When the device switches off after a few seconds, sounding the OFF prompt, it has been reset.
< 1 ... 46 47 48 49 50 ... 78 >

Can’t find what you’re looking for?

Call Us

Call Us

Talk to a product expert
Call Us now at: (877) 871-6755

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)

Chat with Us

Chat with Us

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)

message

Text Us

Text with a support agent via SMS at:
628-333-7807

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)