How To
How To
1869 results
-
• Make sure that JBL DRG is connected via Bluetooth with your smartphone and the JBL DRG” app has been launched. • Search a FM frequency band with your head unit. (an unrestricted frequency would be one that is not occupied by a radio station). • Select “FM” in “Connection Mode” on the JBL DRG App and key in the FM unrestricted frequency you have selected in the right window, JBL DRG will then transfer audio to your head unit and play through your vehicle’s audio system.Was this helpful? Thank you for your feedback!
-
To clean yurbuds, remove the enhancers (tips) from earphones and wash with warm, soapy water. Do not use anything containing alcohol. Completely dry the enhancers and reposition on the earphones, as shown in the Quick Start guide: Left bud between 3:00 and 4:00 position Right bud between 8:00 and 9:00 positionWas this helpful? Thank you for your feedback!
-
You can clean it by wiping it gently with a damp cloth. Take extra care not to let water leak into the speaker chamber, as it will damage the speaker drivers.Was this helpful? Thank you for your feedback!
-
We recommend cleaning the earphones with audio or electronic wipes.Was this helpful? Thank you for your feedback!
-
The firmware version of the headphone will be displayed in the settings page of the app.Was this helpful? Thank you for your feedback!
-
With the SB35 in standby, press and hold Volume plus and Volume Minus for more than three seconds. The software version is now shown on the front panel display, under the fabric grille. It is the first figure that is the software. More info is shown, but is not relevant for user.Was this helpful? Thank you for your feedback!
-
Go to your Bluetooth Settings to confirm that you are connected to both JBL Reflect Fit Audio and JBL Reflect Fit HRM. Once you are connected to the Reflect Fit HRM you will hear the audio voice prompt state, "Searching for Heart Rate"......"Calibrating" followed by a heart beat prompt. It will calibrate for 2-5 seconds followed by "Heart Rate Detected". If it cannot verify your heart rate, the audio voice prompt will advise you to adjust the ear piece. Once it has established your heart rate, you will be able to manually check your heart rate by pressing the heart button located on the RIGHT arm of the neck band.Was this helpful? Thank you for your feedback!
-
Plug in via USB charging port behind the cap on the RIGHT side of your neckband just below the volume controls. When the light is on, your neckband turns green. (Press the plus and minus on the volume control to get the battery status)Was this helpful? Thank you for your feedback!
-
The UA Sport Wireless Heart Rate must be charged with a micro USB charger that is provided in the packaging. You will find the USB outlet located on the bottom left side of the inline microphone. There will be a small rubberized window that you can slide up and over to expose the outlet. After plugging in the headphones, you will see a solid red light appear at the bottom of the inline microphone. Once the headphones are fully charged, the red light will turn off. It typically takes less than 2 hours of charging time to receive the 5 full hours of audio playback.Was this helpful? Thank you for your feedback!
-
The USB charging port will be located on the inline microphone located on the RIGHT side of the earphones.Was this helpful? Thank you for your feedback!
-
You can change the volume on the Harman Kardon Aura Studio 2 by either using the volume control ( indicated with the + and - ) on the front of the Aura Studio 2. Alternatively, when connected by Bluetooth from a mobile device, you can change the volume from the mobile device. There are 32 steps in the volumeWas this helpful? Thank you for your feedback!
-
To remove the enhancer, pinch the edge opposite of the sound tunnel between your thumb and forefinger and firmly pull up and off the ear bud. Replacement enhancers are specific to the left and right ear bud. An (L) or (R) and size indicator is located on the inside of the enhancer. When changing the enhancers, you must place the right enhancer on the right ear bud and the left enhancer on the left ear bud. Firmly grasp the earbud with one hand and align the sound tunnel of the enhancer with your other hand and stretch the enhancer up and over the top of the red earbud. Check the alignment of the sound tunnel to insure best sound performance. If sound is muffled or weak, check and rotate sound tunnel. Most people use the same size for Right and Left but it is possible to use different sizes because some ears are not symmetrical. - If you’re unable to find a secure fit with both sizes in the box, we can send you a complimentary sizing pack with two additional sizes. Please email ua.jblsupport@harman.com to request yours today.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call Us now at:
(877) 871-6755
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat with Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)