How To
How To
1867 results
-
Please refer to the owner's manual for AVR 151 or 151S. The procedure is explained there. The remote control contains a number of pre-programmed command sets that can be activated to control TV sets, disc players and other devices of various brands.Was this helpful? Thank you for your feedback!
-
Here is the pairing procedure between a K915 headset and a new transmitter box: 1. Power off the headphone. 2. Power off the transmitter. 3. Press and hold the power button on the headphone until the “Signal” LED is flashing, and a beep sound can be heard. 4. Power on the transmitter. 5. After a short while the “Signal” LED will light constantly (stop flashing) and the pairing is complete.Was this helpful? Thank you for your feedback!
-
Switch the headphone ON, then press both volume buttons (VOL + and VOL-) at the same time, and hold them for 5-6 seconds. The headphones are now reset to factory default.Was this helpful? Thank you for your feedback!
-
Any changes you make on the Lighting page will be immediately reflected on your headset.Was this helpful? Thank you for your feedback!
-
If your JBL Link 10 or Link 20 is out of range, setting up a personal hotspot from your mobile device will allow your Google Assistant to answer again. However, this process requires two mobile smartphones, one as the "mobile hotspot" and the second to connect the JBL Link 10 or Link 20 to your network.Was this helpful? Thank you for your feedback!
-
By using Google Home app, and if a software is available then the app will notify you about the newest software available. Google Home app can be downloaded from Apple Play Store or Google Play Store.Was this helpful? Thank you for your feedback!
-
If/When a software update becomes available for this product, our upgrade toolkit (HID) can be found on our website HarmanKardon.com. With this tool you are able to update the firmware version of your speaker.Was this helpful? Thank you for your feedback!
-
The speaker will be automatically updated if any new software is available. You can check our HK Alexa setup app for more information, since the app will show a notification that new software was installed. Tap on the icon showing and see all release notes.Was this helpful? Thank you for your feedback!
-
All updates will happen over-the-air, meaning that your device just needs to be connected via your Wi-Fi network with at least 30% battery and plugged into the charger, then it will update during the night if there are any new updates available.Was this helpful? Thank you for your feedback!
-
USB playback is available in US version only. After the USB drive is inserted, press and hold the "Play/Pause" & "Vol +" buttons for 10 seconds to start USB playback. Please note that there are no pause/next track/previous track controls for USB playback.
Was this helpful? Thank you for your feedback! -
When the earbuds are connected to the USB wireless dongle and Bluetooth connection at the same time, triple tab on the left earbud to switch between the two connections. You'll hear a tone after you triple tab the left earbud signaling the switching is in progress. If you receive an incoming call from your mobile device, you can double tap either earbud and the earbuds will automatically switch over to that connection while answering the call.Was this helpful? Thank you for your feedback!
-
Onboard Adaptive Noise Cancellation is controlled by the multi-function button on the rear of the left ear-cup. The feature is switched on by default, but you can SHORT press the multi function button to toggle from ANC to talk-through. Turn off ANC by long-pressing the multi-function button.Was this helpful? Thank you for your feedback!
-
Onboard Adaptive Noise Cancellation is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SHORT press the multi-function button to toggle from ANC to talk-through. Turn off ANC by long-pressing the multi-function button.Was this helpful? Thank you for your feedback!
-
To choose a wireless network for your BDS system, please do the following. 1: Select Choose a network from the Setup Wi-Fi list. 2: Follow the instructions on the screen to select your wireless home network and enter your security password, if applicable.Was this helpful? Thank you for your feedback!
-
By pressing and holding the "Volume+" and "Bluetooth" button together for 5 seconds. A voice will say the version number.Was this helpful? Thank you for your feedback!
-
The red charge light turns off when charging has finished.Was this helpful? Thank you for your feedback!
-
When the Xtreme is ON, the row of 5 diodes at the bottom of the front will light up in turn, with the top flashing LED showing how far charging has progressed. When full charge has been reached, all diodes light constantly. In some cases, the fifth diode keeps on blinking, but does not light up constantly, no matter how long charging continues. Sometimes it will show constant light after charging has been stopped. This is normal, caused by tolerances in the circuits, and is no cause for alarm. The battery is charged to the same level. If the Xtreme is OFF, no diodes will light when full charge has been reached.Was this helpful? Thank you for your feedback!
-
The charging LED stops lighting white, and goes dark.Was this helpful? Thank you for your feedback!
-
The red diode that lights up when charging begins will go out again when charging is complete.Was this helpful? Thank you for your feedback!
-
With the Onyx Studio 2 switched ON, the ON/OFF switch light flashes while the unit is charging. If the unit is switched OFF, no indication shows that charging is taking place, but charging still takes place. When charging is complete, the light becomes constant. There is no battery status indication, so it is not possible to follow the power level of the battery.Was this helpful? Thank you for your feedback!
-
Press and hold the Source, Vol+ and Vol- buttons at the same time until you see the text "reset" on the soundbar's display.Was this helpful? Thank you for your feedback!
-
Press volume + and volume - simultaneously for 5 seconds to reset.
The headphone must be ON while doing this.Was this helpful? Thank you for your feedback! -
On the back of your OMNI BAR+ there is a reset button. Hold it down for 5 seconds, until the round button LED lights up in white. The product is now reset and ready to be set up again.Was this helpful? Thank you for your feedback!
-
The reset procedure is quite different from the rest of the OMNI+ series. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call Us now at:
(877) 871-6755
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat with Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)