How To
How To
1869 results
-
USB playback is available in US version only. After the USB drive is inserted, press and hold the "Play/Pause" & "Vol +" buttons for 10 seconds to start USB playback. Please note that there are no pause/next track/previous track controls for USB playback.
Was this helpful? Thank you for your feedback! -
When the earbuds are connected to the USB wireless dongle and Bluetooth connection at the same time, triple tab on the left earbud to switch between the two connections. You'll hear a tone after you triple tab the left earbud signaling the switching is in progress. If you receive an incoming call from your mobile device, you can double tap either earbud and the earbuds will automatically switch over to that connection while answering the call.Was this helpful? Thank you for your feedback!
-
Onboard Adaptive Noise Cancellation is controlled by the multi-function button on the rear of the left ear-cup. The feature is switched on by default, but you can SHORT press the multi function button to toggle from ANC to talk-through. Turn off ANC by long-pressing the multi-function button.Was this helpful? Thank you for your feedback!
-
Onboard Adaptive Noise Cancellation is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SHORT press the multi-function button to toggle from ANC to talk-through. Turn off ANC by long-pressing the multi-function button.Was this helpful? Thank you for your feedback!
-
To choose a wireless network for your BDS system, please do the following. 1: Select Choose a network from the Setup Wi-Fi list. 2: Follow the instructions on the screen to select your wireless home network and enter your security password, if applicable.Was this helpful? Thank you for your feedback!
-
By pressing and holding the "Volume+" and "Bluetooth" button together for 5 seconds. A voice will say the version number.Was this helpful? Thank you for your feedback!
-
The red charge light turns off when charging has finished.Was this helpful? Thank you for your feedback!
-
When the Xtreme is ON, the row of 5 diodes at the bottom of the front will light up in turn, with the top flashing LED showing how far charging has progressed. When full charge has been reached, all diodes light constantly. In some cases, the fifth diode keeps on blinking, but does not light up constantly, no matter how long charging continues. Sometimes it will show constant light after charging has been stopped. This is normal, caused by tolerances in the circuits, and is no cause for alarm. The battery is charged to the same level. If the Xtreme is OFF, no diodes will light when full charge has been reached.Was this helpful? Thank you for your feedback!
-
The charging LED stops lighting white, and goes dark.Was this helpful? Thank you for your feedback!
-
The red diode that lights up when charging begins will go out again when charging is complete.Was this helpful? Thank you for your feedback!
-
With the Onyx Studio 2 switched ON, the ON/OFF switch light flashes while the unit is charging. If the unit is switched OFF, no indication shows that charging is taking place, but charging still takes place. When charging is complete, the light becomes constant. There is no battery status indication, so it is not possible to follow the power level of the battery.Was this helpful? Thank you for your feedback!
-
Press and hold the Source, Vol+ and Vol- buttons at the same time until you see the text "reset" on the soundbar's display.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call Us now at:
(877) 871-6755
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat with Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)