How To
How To
1867 results
-
Each time the HD 3700 is switched off, the player is reset.Was this helpful? Thank you for your feedback!
-
On the soundbar, press and hold the power and source button for more than
10 seconds.
Please note this procedure will revert ALL settings back to factory default.Was this helpful? Thank you for your feedback! -
Press and hold the "Microphone off" button for 5 seconds. The Allure speaker will tell you when it is ready to be configured.Was this helpful? Thank you for your feedback!
-
You can reach out to the Under Armour Customer Service in the USA by phone at 1.800.377.9952 or by e-mail at ua.jblsupport@harman.com.Was this helpful? Thank you for your feedback!
-
To prevent other people from changing the source on your BDS through Bluetooth, you can disable the “Automatic Playback” function in the System Settings of the BDS ( 280, 580, 280S and 580S ). This does not prevent others from connecting to one of the two Bluetooth receivers in the BDS units, but it prevents other people from “interrupting” your playback source. This is where the change is done: Settings – System Settings Automatic Playback ( Enable/Disable ) Enabled: People can connect to your BDS and start playing music/audio. Your BDS will automatically change source ( or switch on, when BDS is in Standby mode ) from any source. Disabled: People can connect to your BDS, but the BDS will not automatically change source, or go out of Standby mode when a music/audio signal is sent through Bluetooth.Was this helpful? Thank you for your feedback!
-
To play the surround sound with DOLBY ATMOS or DTS:X, connect your Blu-ray player or other digital device to the HDMI input connector on the soundbar. If the TV support Dolby ATMOS, served over HDMI ARC, just make sure it is selected in the TV setting menu. To select the most suitable amount of sound effect of DOLBY ATMOS and DTS:X, press on the remote control ATMOS level button, to switch between MID, HIGH, LOW or OFF. Note: If your TV has an eARC HDMI input, you can connect your Blu-ray player or other digital device to the HDMI IN connector on the TV.Was this helpful? Thank you for your feedback!
-
On the back of the SB150 subwoofer, you will find a "pair" button. Hold down the pair button for 3 seconds. It will start flashing amber rapidly, indicating that the pairing mode has begun. You don't need to press other buttons to make a connection, once the amber light is steady, it is connected to your SB150 soundbar.Was this helpful? Thank you for your feedback!
-
You can only pair bluetooth after you've successfully setup your Invoke. To put it in pairing mode, press the bluetooth button until the light flashes. You are now in pairing mode. Locate the Invoke on your device (phone, tablet, etc.) Select the Invoke. You should receive a tone indicating the pairing process is complete.Was this helpful? Thank you for your feedback!
-
We have some suggestions if you want to enjoy the best performance from your Bluetooth devices. 1. Please note that if you have a large number of Apps open in your smartphone or tablet, this may block or overtax its processor. Dropouts may result. Try to close all or most active apps. This should solve the problem. 2. Bluetooth signals from smartphones and tablets are not very strong. Make sure that the signal does not have to pass through doors, walls etc. Always maintain a clear line of sight between transmitter and receiver. 3. Do not carry your smartphone in your pocket, if you have dropouts. Your body can act as a screen, reducing the strength of the Bluetooth signal. Put the phone on a table or other surface. 4. Do not walk around while listening. If the transmitter and the receiver are moved in relation to each other, dropouts occur more frequently. 5. Under normal circumstances, you can expect a range of 5 meters with no problems, if you follow the above advice. In some instances range is longer, but we cannot promise this.Was this helpful? Thank you for your feedback!
-
That is easy, simply say "Alexa, mute" or "Alexa, mute music". To resume playback if needed, say "Alexa, resume playback".Was this helpful? Thank you for your feedback!
-
If you are not using the microphone, make sure that any communication software such as Zoom, Skype, Discord, etc. are closed and that your microphone is muted. You can also take advantage of it's Dual Connect feature and place one of the earbuds in the charging case and speed charge the earbuds to extend the playback time.Was this helpful? Thank you for your feedback!
-
Unfortunately, the JBL AmpUp App is no longer available for download.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call Us now at:
(877) 871-6755
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat with Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)