How To
How To
1867 results
-
No, since the speaker does not store any information locally. To remove all settings from your stolen device, simply unlink the speaker from your account, and the next time the speaker goes online it will not connect to your account. However, if you have used the command ""Remember this"" feature, please beware of sensitive information, as the speaker will inform you of whatever you have asked it to remember. But after unlinking the speaker, it will forget.Was this helpful? Thank you for your feedback!
-
There will be times that the LEFT ear will disconnect from the RIGHT or (primary) earbud. To get the Left ear to reconnect, make sure that the RIGHT earbud is on and emitting sound. Take the LEFT ear out of the charging case and put in ear. Press and hold down the power button on the LEFT ear bud for 5-8 seconds. You should hear the power on chime and then both ear buds should emit sound now.Was this helpful? Thank you for your feedback!
-
No, your subwoofer is not defective at all! This is normal and by design of the product after it has been paired for a longer period of time.Was this helpful? Thank you for your feedback!
-
We are sorry about this problem. EuP regulations require that electronics go into full off after some time. Unfortunately, this means that the soundbar cannot be woken up again after half an hour. It is necessary to use the ON/OFF switch.Was this helpful? Thank you for your feedback!
-
We are sorry about this problem. EuP regulations require that electronics go into full off after some time. Unfortunately, this means that the soundbar cannot be woken up again after half an hour. It is necessary to use the ON/OFF switch.Was this helpful? Thank you for your feedback!
-
Sounds like your JBL LINK 10 or LINK 20 has been connected to another Wi-Fi network. It is very simple to reconnect to your Wi-Fi by using the Google Home app. Simply select your Wi-Fi in the app, and you're all set. All information about the speaker and voice teaching is stored in the Cloud, so you do not have to do this again.Was this helpful? Thank you for your feedback!
-
To install your JBL LINK speaker using Apple iOS... 1. Download the Google Home app. 2. Activate your Bluetooth connection, as it is required for Apple devices. 3. Follow the instructions in the Google Home app.Was this helpful? Thank you for your feedback!
-
This headphone is supported by the My JBL Headphones App.Was this helpful? Thank you for your feedback!
-
Some of the DJ EQ curves have been removed from the My JBL Headphones app. Harman will ‘continuously’ update the My JBL Headphones app with new DJ sound-curves as this number changes based on who we sign agreements with and when.
See the release notes for app version 4.10.9 below:
- Adding support for TOUR PRO+ TWS and TOUR ONE Global version
- Removing expired DJ’s signaturesWas this helpful? Thank you for your feedback! -
With some phones, such as iPhones and some Android models, volume is synchronized while Bluetooth is used, and levels below volume setting 6 (tested with iPhone 6 and iPhone 5s) and volume setting 5 on most Android devices will cause the GO to enter standby after some minutes. If you want to play softer while still using your iPhone as a source, please change to cabled connection from the headphone output to the AUX input of GO. This will make it possible for you to set the GO's volume at its minimum step, and then control total level on the telephone. Of course, if source level from the telephone is set extremely low, the GO will go into standby again, because GO needs a certain level to keep playing. Alternatively, use a phone which does not synchronize volume as source. Many Android phones do not synchronize volume, so by using such a phone, you can adjust GO to its lowest level, adjusting total level independently, even via Bluetooth. This will usually result in music volume at the desired level.Was this helpful? Thank you for your feedback!
-
Tap-hold on the right ear bud forcefully to reconnect heart rate. If this does not work, Hold the middle button to turn off, then back on your headphones.Was this helpful? Thank you for your feedback!
-
If you are experience problems with reading any CD disc, please go to an authorized service center for help.Was this helpful? Thank you for your feedback!
-
A certain degree of sensitivity is necessary to make the response system function. In some cases, hair or a cap touching the sensor plates can activate the system, even if you do not want it. The solution is to lock the sensor system. Put your finger on the left sensor plate, and hold it there for more than 4 seconds. Now the sensors are locked, and the problem is solved. Unlocking is done the same way.Was this helpful? Thank you for your feedback!
-
The Go+Play Wireless must be in Standby to be able to switch On when receiving a signal. This function uses a small amount of power, and cannot be switched off. Remove batteries when not in use for more than 2 weeks to prevent power draining.Was this helpful? Thank you for your feedback!
-
Sometimes after a system update, many Bluetooth connections and application handshakes no longer function. Therefore we advise to delete the existing pairing, and restart your smart device/telephone/tablet computer. After restart is completed, please connect to the product once again via Bluetooth. It should now be visible in our HK Remote app.Was this helpful? Thank you for your feedback!
-
Fortunately the Go+Play in all versions is made with this problem in mind. One of the feet is adjustable. Look at the four feet. One is different from the others. You can insert a 3mm hex key into the center hole in it, then loosen the foot insert and unscrew it until the unit is steady. The adjustable insert may stick a little, so exert a steady, firm pressure to get it loose if this is the case.Was this helpful? Thank you for your feedback!
-
Voice commands can only be triggered by the user who registered them during setup.Was this helpful? Thank you for your feedback!
-
Yes, rinse it under a faucet or under the shower, but not under full water pressure.Was this helpful? Thank you for your feedback!
-
Try below steps. Attach the charger so the device is charging. While charging: First try to hold the "Volume +" and "Phone" buttons at the same time for more than 3 seconds (this resets the Flip 3 to factory settings). If this does not help, press and hold the "Volume +" and "Link" buttons for more then 10 seconds (this will exit demo mode). As a last step, short press on the "Volume -" & "Volume +" & "Phone" buttons. If the device will still not turn on, it has a defect.Was this helpful? Thank you for your feedback!
-
1. Insert both earbuds into the charging case.
2. Try to click 5 times on both left and right earbuds button simultaneously, to reconnect left and right earbuds.
Was this helpful? Thank you for your feedback! -
Your JBL speaker is waterproof with IPX7 rating. (IPX7 means it can survive immersion in 1 meter/3.3 feet for up to 30 minutes.) To maintain the looks and functions of your speaker, please make sure to rinse it with fresh water after using it at a swimming pool or the ocean, then dry off all covers and areas where water can gather. The standard for waterproofing is for tap water. Chemicals and salt in your pool or the ocean can damage the waterproof seals or harm the surface finish over time if not rinsed off after use.Was this helpful? Thank you for your feedback!
-
Make sure your home network's Internet connection is active and the Citation speaker is placed within Wi-Fi range. If you are using a Wi-Fi extender, your speaker may be confused which network to connect to. If this is happening, try moving the speaker closer to the main router and renaming the Wi-Fi extender.Was this helpful? Thank you for your feedback!
-
This can be caused by many things. It could be obstacles between your device and router, or that your device has been placed too far away. To enhance the WiFi signal for your BDS, please make sure to place the included antenna on its threaded socket, then try search for any WiFi network again. If this still does not work, try moving your BDS closer to the router until connection is established, ensuring that the BDS WiFi network module is working. If nothing happens, the network module of the BDS or your router have a problem. In case you need more help, contact our support for more tips.Was this helpful? Thank you for your feedback!
-
We always recommend to use the online updating tool inside BDS, as it is connected directly to our server and if new software are available, it will be there first. We are trying to update our website as quickly as possible.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call Us now at:
(877) 871-6755
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat with Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)