How To
How To
1869 results
-
The SB20 supports these programmable IR codes for your TV remote: Volume+, Volume-, Mute and Power commands.Was this helpful? Thank you for your feedback!
-
Yes, but only via cable, and noise cancelling cannot be activated meanwhile. Since the charging socket is located on top of the ear pod, adjustment is limited in that direction while the micro-USB plug is inserted.Was this helpful? Thank you for your feedback!
-
No, the noise cancelling function is always active when Bluetooth is on. If you want to listen to music without NC on, you must use the cabled audio connection.Was this helpful? Thank you for your feedback!
-
Yes, charging and listening simultaneously is possible. With N90Q, charging takes place at all times when listening to digital audio from a USB socket.Was this helpful? Thank you for your feedback!
-
No, in order to go through the setup procedure, it is necessary to activate the (OSD) On-Screen-Display, and this is not possible on the front panel buttons, you need the remote control. Only the remote control features the necessary OSD button.Was this helpful? Thank you for your feedback!
-
Yes, the Harman Kardon SB20 features IR learning functionality. Please follow these steps:
- Power on your Harman Kardon SB20.
- Press and hold the SB20 surround button for 5 seconds. This will make the system enter IR learning mode. The power button will flash amber while in learning mode.
- Now the SB20 can learn to respond to your TV remote control. These commands can be learned: To learn the SB 20 VOL+ command, press volume + on the SB 20 top panel, then press VOL+ on your TV remote control. The power button should blink amber, and the surround button will light up for 1 second. This will indicate that the process was successful. Repeat the procedure for volume-, mute and power on/off.
- To exit the learning mode, press and hold the surround button for 5 seconds again. The power button light goes out.
Was this helpful? Thank you for your feedback! -
Yes, they are quite easy to remove, and with a little care, new ear pads can be fitted in one or two minutes. You can do this yourself.Was this helpful? Thank you for your feedback!
-
Yes, press Volume + and Surround button at the same time for 5 seconds.Was this helpful? Thank you for your feedback!
-
Yes, this can be done very easily by doing the following procedure: 1: Power on the Cinema Base. 2: Simultaneously press the “Surround” and “VOL –” buttons (at the same time). 3: The Cinema Base source LED button will light amber in color, for 1 second, then the power button LED light will go off and on. 4: Your Cinema Base is now reset.Was this helpful? Thank you for your feedback!
-
Yes, by holding down Volume+ and surround button for more than 5 seconds will reset the SB20. The SB20 will automatically reboot itself, after it has been reset.Was this helpful? Thank you for your feedback!
-
Yes, switch the soundbar ON, then press the volume - ( minus ) and surround buttons at the same time for 5 seconds. Now the device is reset.Was this helpful? Thank you for your feedback!
-
The JBL Cinema SB450 can be reset to its default factory settings and erasing all programming. To reset the soundbar, press and hold Volume+ and Virtual Surround buttons for 5s.Was this helpful? Thank you for your feedback!
-
There are 5 leds which indecates the current charge level, Each led indicates 20% of charge.Was this helpful? Thank you for your feedback!
-
No, NC is always on when Bluetooth is on. However, it is possible to select NC on or off when listening via cable.Was this helpful? Thank you for your feedback!
-
No. There is no way to turn off the blue LED light from our wireless headphones unless they are turned off.Was this helpful? Thank you for your feedback!
-
Yes, Alexa has various voice commands to turn up the volume. Try saying "Alexa, turn it up" or "Alexa, set volume to 5".Was this helpful? Thank you for your feedback!
-
While this is indeed possible, no such cable is made by AKG, so only cables from third-party manufacturers may be considered. Please note that internal pin configuration must be identical to the original cable for such a cable to work with the headphones.Was this helpful? Thank you for your feedback!
-
No, this is not possible. Even though the MMCX (micro-miniature coaxial) connectors seem identical, they are not the same dimensions.Was this helpful? Thank you for your feedback!
-
Yes, two headsets can be used simultaneously with one transmitter.Was this helpful? Thank you for your feedback!
-
No, we only have support for MHL compatible devices, which Chromecast do not support.Was this helpful? Thank you for your feedback!
-
Our BDS system does supports WPS PIN, please do the following:
- Select WPS PIN from the Setup Wi-Fi list. A PIN code is displayed on the screen.
- Enter this same PIN on your wireless router’s internal web page to connect. See your router’s user manual for more details.
Was this helpful? Thank you for your feedback! -
No, it is not recommended to connect only one input on our Dual Tweeter models. These models are built using Dual Voice Coil woofers and driving only one half of the motor structure is not healthy for the speaker and will shorten its life expectancy.Was this helpful? Thank you for your feedback!
-
For your personal safety and to avoid possible damage to your equipment and speakers, it is always a good practice to turn off and unplug the AVR and ALL source equipment from the AC output before making any audio or video system connections.Was this helpful? Thank you for your feedback!
-
For your personal safety and to avoid possible damage to your equipment and speakers, it is always a good practice to turn off and unplug the AVR and ALL source equipment from the AC output before making any audio or video system connections.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call Us now at:
(877) 871-6755
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat with Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)