How To

Yes, but only via cabled connection. When you insert the USB charging cable, Bluetooth is switched off, so wireless listening is not possible.

Unfortunately, you cannot turn on and use the headphones while they are charging.

No, this feature is not supported in our Harman Kardon Allure speaker. This might change with future updates. You can call your Amazon friends by using the Alexa app.

Speakers are associated with each other from the factory. If one of them fails, and you get a replacement, then you will need to follow the association section in the owner's manual, so you can pair your new speaker with the one you have. We do not recommend doing this to mix differently colored speakers, only if one of them becomes defective.

Yes, these headphones can be connected and paired to two devices at the same time.

Yes, steam and drops of water in a bathroom are fine.

Yes, steam and drops of water in a bathroom are fine.

Yes, you can use them for telephone conversations in both Bluetooth and wired mode when paired with a smart device. 

Yes, you can play game either wired or wirelessly while using USB-C charging cable.  

Yes, Zone 2 can play compatible contents of a USB stick inserted into the front panel of the receiver.

Yes. Out-the-box the JBL Bar series soundbar recognizes volume and mute controls from the most common TV remote controls. The JBL Bar series has IR learning. You can use this feature to teach the soundbar to response to your TV's remote control as well.

Yes, use the MONITOR OUT sockets (1/4” and RCA are available on 208P, RCA on ONE) to feed into a recording device. Please note that these outputs are volume controlled, so set the volume correctly, depending on the sensitivity of the recording device.

It is possible to replace the ear pads, but there are details to consider. On Elite 700: The ear pads are held in place by a plastic plate with claws, and some of the claws will most likely break off when you remove the pad. You do this by grabbing under the edge where the fabric ends, then pulling hard outward. The claws will eventually let go, and some of them will break off, rattling inside the ear pod. The only way to get them out is to unscrew the speaker plate, lift it up, and shake out the broken-off claws. The new pads are simply centered over the speaker plate, and the claws pressed into the holes with a firm pressure. On Everest 700: The ear pads are glued into position with double-adhesive tape. Pull the old pads off with a forceful, steady pull, until the glue lets go. Remove the protective layer on the new pads, and carefully position them correctly before pressing home all the way around the edge.

Yes, the ear pads are replaceable by owner. The pads can be purchased as spare parts from the service center, or purchased directly from the JBL spare parts web shop, when opened.

No, the pads are glued to the headphone body, and must be replaced by a service technician.

Yes, when unit is on, press and hold Source and Power buttons for about 6-7 seconds.

If you want to change Bluetooth source, you may have to reset the Bluetooth system in the AURA. To do this, hold your finger on the input selector field (circle with arrow pointing in) on the side of your AURA for at least 3 seconds. Now the previous source is deleted, and you can pair a new source and play from it.

Yes, on the master speaker (the one with playback buttons), simply press the Reverse and Forward Play buttons at the same time for 3 seconds. Please note that after you have performed the reset procedure, master and secondary speakers are no longer connected. Go to the owner's manual page 4, the section "speaker association", to pair the secondary and master again.

Yes, simply press and hold Volume + & phone button at the same time. When the unit is reset, it will power off, and turn on the unit again, and it is reset.

Yes it is possible to reset your speaker. The reset will remove all Bluetooth pairings and WiFi network settings. In power ON mode, press and hold the Power Button for at least 10 seconds, until the volume and input selector lights begin to flash. Your JBL Authentics L8 or L16, are now back to factory settings. Please reconnect the speaker to your WiFi network again.

Yes, turn on your Onyx studio 2 and hold down phone button & volume + at the same time. Onyx Studio 2 will power off and when you power it on again, it has been reset.

Yes, you can see all voice interactions with the Harman Kardon Allure by using the Alexa app and visiting History in Settings. Your interactions are grouped by question or request. Tap an entry to see more detail, provide feedback, or listen to audio sent to the Cloud for that entry by tapping the play icon. Sometimes Alexa may not understand you perfectly, and the translations you see in History may not always reflect exactly what you said (for example, they may be inaccurate or incomplete). You can help us improve your experience by providing feedback on inaccurate translations in History.

Yes, and it is very simple. Choose the custom setup option if you want to manually connect the BDS system to Wi-Fi. To connect the BDS system to a specific Wi-Fi network, you need to enter the Wi-Fi network name and password in the network settings. Confirm the SSID name. Your BDS should now be connected to the WiFi.

No, this is not possible.

Yes it is possible. Connect any iOS device (iPhone, iPod touch or iPad) to the front panel USB port of the BDS. Make sure Wi-Fi is enabled on your iOS device and that it is currently connected to your wireless home network. NOTE: iOS version 5 or higher is required for iOS Wi-Fi sharing.

1. Select Configure Wi-Fi by iOS from the Setup Wi-Fi list. A pop-up will be displayed on your iOS device.
2. Select Allow to confirm that you want to share your Wi-Fi settings.
3. The connection should now be established automatically. Check the status on your TV for confirmation"

You can only share the sound via JBL Connect through Bluetooth connected devices. TV sound is not permitted as it would cause lip-sync issues.

Yes, the E45BT headphones also have an detachable audio cable that you can plug into the headphones. The plug is located at the bottom of the right ear cup.

Yes, Control Xstream is a Chromecast device that allows you to cast music content via your Chrome browser. However, the JBL Control Xstream is not made for video purposes, because there will be delay between sound and image.

Yes. The Google cast function works independent to that of Bluetooth, therefore you are able to Bluetooth connect to another device while casting audio to the JBL Playlist simultaneously. This feature is applicable on smartphones, tablets/iPad, and Bluetooth capable computers.

Yes. Just connect the analog output from your CD player to the Audio In jack on the back of your Adapt.