How To

Support Overview / How To

How To

1874 results
  • What is the Frequency response of the Citation series?
    The Frequency response for the Citation series, except the subwoofer, is 50Hz to 20Khz.
     
  • What is the function of the EQ Button in the remote app for AURA?
    The EQ Button activates a special "wide stereo sound" effect. It does not affect bass settings. Turning EQ On/Off does not reset bass level to default value. User can adjust BASS in the Bass +/- control in the APP.
  • What is the latest software version available for Flip 3?
    Software version v.7.9 is the latest for the Flip 3
  • What is the length?
    JBL Bar 9.1 is 884 mm (without the surrounds in charging position). Surrounds add approx. 160 mm on each side, in charging position.
  • What is the Lexicon DD8 power output at 4 ohms?
    The same as the 8 ohm output, 125 watts/channel.
  • What is the maximum number of speakers that I can connect together via the Dual Sound feature?
    Wireless Dual Sound feature supports a maximum of two speakers. Both the GO + PLAY MINI and the other speaker must have the Dual Sound feature.
  • What is the maximum video resolution of the No. 40 HDMI card?
    The maximum video resolution of the No. 40 HDMI card is 1080i.
  • What is the No. 536 power consumption for the various operational and standby modes?
    The No.536 has several operational and standby modes - the measurements below represent typical values measured at 120VAC: Mode Typical Power Consumption Notes On 210 Watts With no input or output loading Normal (standby) 4.1 Watts/100 Watts Unpon initial power-up/After first use Power Save (Standby) 4.1 Watts Green (Standby) 0.3 Watts OFF 0 Watts Via rear panel switch Note that the No. 536 cannot be shut off by the front button – this is used only for switching the amp in/out of a standby mode. Also note that when set to the Normal standby mode, the amplifier will initially consume the same power as when in the Powersave mode but will change to a higher level after it is switched on for the first time.
  • What is the No. 585 power output into 4 ohms?
    The No. 585 will deliver 350 watts into 4 ohms
  • What is the overall power rating of the Citation MultiBeam 1100?
    The overall power rating is 630 W maximum power at 1% THD.
     
  • What is the procedure to reset Xtreme?
    With the speaker ON, press and hold the VOL+ and Pause/Play buttons for 5-6 seconds. The Xtreme shuts down, and is now reset. You will need to 'forget' the speaker in Bluetooth settings on your phone/tablet in order to pair it again.
  • What is the purpose of having dual tweeters on a speaker?
    Speakers will dual tweeters gives listeners the ability to have a single speaker to drive two independent channels, ideally stereo left and right. Dual tweeter speakers are usually used for in-ceiling audio applications. They have four terminals (two sets of positives and negatives) used to plug in speaker wires from the amplifier.
< 1 ... 139 140 141 142 143 ... 157 >

Can’t find what you’re looking for?

Call Us

Call Us

Talk to a product expert
Call Us now at: (877) 871-6755

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)

Chat with Us

Chat with Us

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)

message

Text Us

Text with a support agent via SMS at:
628-333-7807

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)