No, the tool will tell you to switch them ON when necessary.

It is not a bad idea to have the headphone charged before updating, but only if it is completely empty will there be any difference. To update via cable, a USB cable connection must be established between the headphone and the computer, and since the cable is also used for charging, there will be power to the headphone as long as it is connected to the computer. If the battery is depleted, it may be necessary to wait a little while, until a basic level of charging has been reached. Please note that the ELITE models with the most recent software permit wireless upgrade, directly from the control app on a smartphone. In this case, it is of course necessary to have power enough in the battery to sustain the whole upgrading process, since it takes place without cable.

Sorry, neither AAC nor aptX are supported.

No, the IP waterproof specification means that these speakers can be immersed in water 1 m deep for 30 minutes. It does not mean that they can float, so please be careful. If dropped, they will sink to the bottom.

Yes , all 5 models have voice prompts. The Elite models have the added option of turning off the voice prompts in the settings menu of the app. The Everest 300 and 700, as well as the successors 310 and 710, have the option of choosing between voice prompts and tone prompts. This is how you do it: Switch the headphones ON. Press and hold the Shareme and the Volume Plus buttons for about two seconds. Switch the headphones OFF. You will now hear the OFF prompt having changed to the prompt you did not use before, and you will hear this one until you change it again.

Yes, the Reflect Aware features a three button inline microphone that allows you to control the volume.

No. UA Train does not support AptX™ and AptX HD™ audio codecs.

Every home is different, so it is difficult to provide a universal guide that suits it all. What you can do is check the number of available access points in your home by performing a Wi-Fi network scan using a mobile device. Then select the Wi-Fi channel that isn't as busy as the rest. Also, check how much noise each speaker has using the Harman Kardon Controller app. Simply go into the settings menu and select "Send us feedback" to see the results, signals between -40 dB and -62 dB are considered good.

Cables and other spare parts for EVEREST can be obtained from either the distributors or from authorized service centers. Please contact Harman Customer Support to get the necessary contact details.

Yes. Pair your device with the speaker via bluetooth.

Yes, a phone with GPS capabilities is needed so that the Vi Fitness app can start and stop workouts, track biometrics, measure and store data, track features like elevation and location, and play music during training. We support iOS (9+) and Android OS (Lollipop +) devices however we recommend having the latest OS on any device for the best Vi experience.

If your DSP Tuning Software is not responding properly or is crashing, it is likely because the proper USB driver has not yet been installed.  There is an easy fix for this, and it does not require you to uninstall anything.

 

1. If the tuning software is open, close it.
2. Go back to your software install files and double-click on “USB Driver”.

NOTE: Make sure to allow it to make changes to your computer if your anti-virus software requests it.

3. After the driver is installed, reopen the software.  Your problem should be resolved.

The Onyx Studio 7 features Dual Wireless Sound which allows you to connect two Onyx Studio 7 speakers together for a more powerful listening experience. Please note: You cannot connect the Onyx Studio 7 to other Onyx Studio speakers such as the Onyx Studio 6 and 5. 

It's normal that music will be interrupted for one or two seconds when entering Wireless Dual Sound mode. The two compatible speakers are synchronizing with each other during this connection process. Once they are in sync you will not experience any further interruption.

To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.

The ear pads can be removed and washed.
To remove the ear pads, rotate them anti-clockwise to unlock (see image below).

The ear pads must be hand washed only, do not machine wash - the water temperature used should be in the range specified below. Then wait for the ear pads to fully dry.

Once fully dry, align the holes on the inside of the ear pads (highlighted with orange circles in the image below) with the clips on the headphones (located where the red arrows are pointing in the image below), now rotate the ear pad clockwise to lock the ear pads to the headphones again.

The SmartThings app works with Alexa and can be used to control compatible products such as light bulbs, on/off switches, dimmer switches, thermostats, locks, and Scenes configured with the SmartThings app. To use your speaker to control these smart devices, follow these steps:

1. Go to the speaker's page in the SmartThings app.
2. Select Menu (3 dots on the top right corner).
3. Select "Settings".
4. Select "SmartThings with Alexa".
5. Tap "Allow" to let Alexa to access all your compatible home devices.
6. Select "Link".
7. Tap "Done".

Demo mode

1. Press the Play and Boost button at the same time for 5 seconds.
2. Depending on what state your JBL Partybox is in, either you enter Demo mode or disabling it.
   1. NOTE: In Demo mode, you cannot use the JBL Partybox as most features and buttons are not working.

Here is how to add music to the Dive Headphones: 1. Place the MP3 music files that you want to transfer to the Dive headphones on your computer, where you can find them again. The sequence is not important, they will be played in alphanumerical sequence. If you want to have a special sequence to your tracks, you can add a number as the first file name. 2. Connect the Dive to your computer with the USB cable. Please use the cable that came with the headphones, since other USB cables may be wired for charging only, and may not work. 3. Your Dive will now pop up in your explorer folder overview as a new drive. Total capacity is about 991 MB. 4. Now you simply drag-and-drop the MP3 files from their location onto the Dive, or you mark the files, copy them and paste them onto the Dive. Do not use folders of any kind, and do not try to place other file types on the Dive's memory. MP3 files with a resolution of 320 kbits/second is maximum quality possible. Please note that the owner's manual contains an error about random play, stating that MP3 play will always be done in random sequence. Unfortunately, this is an error. All replay of MP3 files from the internal memory is alphanumerical, NOT random. As mentioned above, you can add a number to the track title, and the tracks will be played in numerical order, until no more numbers are present, after which replay is in alphabetical order.

The Endurance headphones do not support Apt X or AAC audio codecs.

Fully charge the earbuds along with the charging case before the first use. The charging case is for charging the earbuds only. LED behaviors: 1 LED- 25% 2 LED-25%-50% 3 LED-50%-75% 4 LED-75%-99% NO LED-100% Fully Charged You can keep the earbuds in standby mode for up to 3 hours without having to return them to the case. beyond this point the earbuds must be returned to the case for charging. You should receive up to 4 hours of playback with additional 24 hours of backup power from the charging case.

If connecting for the first time, the headphone will enter pairing mode automatically after it is powered on. To turn the headphones on, simply spread apart the RIGHT power hook from the cord. You will see solid red LED and then it will flash blue as it begins to search for a device to connect to. The Endurance headphone should pop up on your discoverable devices within a few seconds and you should be connected! If you wish to turn off the headphones, remove them from your ear and allow the RIGHT power hook and cord to close together. This is magnetized, so they should close together with ease.

To answer call, press the "L" on the JBL logo on the RIGHT ear for 1 second. To hang up, press the "L" for 1 second. To ignore the call, press and hold the "L" for 2-3 seconds.

To pair to a different device, double tap and hold your finger on the JBL logo for 5 seconds until you see the LED light flash blue. Make sure that the device you are trying to connect to is in range and in pairing mode. You should see the Endurance headphone pop up on your discoverable devices within a few seconds and the flashing LED light should now be a solid blue.

To pause/play press the "L" on the JBL logo located on the RIGHT ear for 1 second. If you want to skip the track forward, press the "L" on the JBL logo on the RIGHT ear hook for 2 seconds. To skip tracks backward, press the "L" on the JBL logo on the RIGHT ear hook for 3-4 seconds.

To control the volume, simply move your finger up the ridges above the JBL logo on the RIGHT ear to increase the volume. To decrease the volume, move your finger down along the ridges.

In order to adjust your EQ settings you must follow these instructions:   In your Windows 10 taskbar, right click on the volume icon. It should bring up your selected output device. If “Speakers (JBL Quantum *model* Game)” is not selected, please proceed to the next step.
In the upper right hand corner, select the arrow. This will display a list of output devices on your PC. Please select “Speakers (JBL Quantum *model* Game)” After selecting 'speakers' you will now be able to adjust your EQ settings to your preference.

Power on the speaker Press and hold the Volume + button and the Bluetooth button together for 3-5 seconds until the speaker turns off Once turned off, the speaker has been reset to the factory default settings

To reset the device to its factory settings: 
Power on the speaker. While on, press and hold the power button down for 15-20 seconds until the speaker turns off.

Now that the speaker has been reset, make sure to remove it from your BT settings if it was once paired to other devices as the BT memory has been reset as well. Once you turn the speaker on again, it should automatically enter into pairing mode with a flashing LED. It should pop up on your discoverable devices under your BT settings and connect within a few seconds. 

To reset your speaker to its factory settings, press and hold the Bluetooth and Vol + buttons for at least 10 seconds. The LED will emit a constant amber color until the reset is completed.