How To

To get the full potential of the HDMI content/source you have in your home, then you need to enable HDMI UHD deep color option on your TV for the HDMI output port (ARC).

Since there are tons of different TVs and manufactures out there, the best way to see if your TV can use 10-bit color on HDMI, is to read the TV's manual or call their support section.

Press the Bluetooth source button on your BDS remote. In the right top corner of your TV screen, there should be a button called "Pair". Jump to the "Pair button" to perform pairing by using the arrow keys on your remote control. Click OK while being on the pair button. Once pressed, a pop-up screen will appear, this indicates pairing mode is active for 3 minutes. Go to Bluetooth settings on your mobile device, find the BDS in the list and connect. If you want to pair a second device, please repeat the procedure to activate pairing mode.

For Citation ONE, Citation 100, Citation Sub and Citation Surround, Press and hold the RESET button on the speaker for 5 seconds. For Citation 300, Citation 500, Citation Bar and Citation Tower, Press and hold the RESET button on the speaker for 5 seconds, or select the Factory Reset option in the touch screen settings menu.

Once the speaker/soundbar is connected to the network, software updates will automatically be sent to the speaker/soundbar through Wi-Fi or the internet, if available

In the JBL ONE App:
(1) Go to My Products, select your product
(2) Select Support tile
(3) Under General, select Product Support

After setting up one or both voice assistants on your JBL Authentics speaker, you must make sure that you have connected your supported music service account to your Amazon and/or Google account in the Alexa and Google Home apps.

For Alexa, if you then set one of the music services as default in the Alexa app settings, you can play music from this service just by asking Alexa to play music.

Unfortunately, the JBL AmpUp App is no longer available for download.

If you are not using the microphone, make sure that any communication software such as Zoom, Skype, Discord, etc. are closed and that your microphone is muted. You can also take advantage of it's Dual Connect feature and place one of the earbuds in the charging case and speed charge the earbuds to extend the playback time.

That is easy, simply say "Alexa, mute" or "Alexa, mute music". To resume playback if needed, say "Alexa, resume playback".

We have some suggestions if you want to enjoy the best performance from your Bluetooth devices. 1. Please note that if you have a large number of Apps open in your smartphone or tablet, this may block or overtax its processor. Dropouts may result. Try to close all or most active apps. This should solve the problem. 2. Bluetooth signals from smartphones and tablets are not very strong. Make sure that the signal does not have to pass through doors, walls etc. Always maintain a clear line of sight between transmitter and receiver. 3. Do not carry your smartphone in your pocket, if you have dropouts. Your body can act as a screen, reducing the strength of the Bluetooth signal. Put the phone on a table or other surface. 4. Do not walk around while listening. If the transmitter and the receiver are moved in relation to each other, dropouts occur more frequently. 5. Under normal circumstances, you can expect a range of 5 meters with no problems, if you follow the above advice. In some instances range is longer, but we cannot promise this.

You can only pair bluetooth after you've successfully setup your Invoke. To put it in pairing mode, press the bluetooth button until the light flashes. You are now in pairing mode. Locate the Invoke on your device (phone, tablet, etc.) Select the Invoke. You should receive a tone indicating the pairing process is complete.

On the back of the SB150 subwoofer, you will find a "pair" button. Hold down the pair button for 3 seconds. It will start flashing amber rapidly, indicating that the pairing mode has begun. You don't need to press other buttons to make a connection, once the amber light is steady, it is connected to your SB150 soundbar.

To play the surround sound with DOLBY ATMOS or DTS:X, connect your Blu-ray player or other digital device to the HDMI input connector on the soundbar. If the TV support Dolby ATMOS, served over HDMI ARC, just make sure it is selected in the TV setting menu. To select the most suitable amount of sound effect of DOLBY ATMOS and DTS:X, press on the remote control ATMOS level button, to switch between MID, HIGH, LOW or OFF. Note: If your TV has an eARC HDMI input, you can connect your Blu-ray player or other digital device to the HDMI IN connector on the TV.

To prevent other people from changing the source on your BDS through Bluetooth, you can disable the “Automatic Playback” function in the System Settings of the BDS ( 280, 580, 280S and 580S ). This does not prevent others from connecting to one of the two Bluetooth receivers in the BDS units, but it prevents other people from “interrupting” your playback source. This is where the change is done: Settings – System Settings Automatic Playback ( Enable/Disable ) Enabled: People can connect to your BDS and start playing music/audio. Your BDS will automatically change source ( or switch on, when BDS is in Standby mode ) from any source. Disabled: People can connect to your BDS, but the BDS will not automatically change source, or go out of Standby mode when a music/audio signal is sent through Bluetooth.

You can reach out to the Under Armour Customer Service in the USA by phone at 1.800.377.9952 or by e-mail at ua.jblsupport@harman.com.

Press and hold the "Microphone off" button for 5 seconds. The Allure speaker will tell you when it is ready to be configured.

On the soundbar, press and hold the power and source button for more than
10 seconds.

Please note this procedure will revert ALL settings back to factory default.

Each time the HD 3700 is switched off, the player is reset.

With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks slowly for about two seconds, and now you have reset to factory settings.

You can reset the E25BT in two ways: 1: Press and hold Volume + and Volume - simultaneously for more than 3 seconds. This resets to factory settings, clearing the pairing list. 2: With unit in ON mode, plug in the USB cable. This resets the unit and puts it into charging mode.

With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks slowly for about two seconds, and now you have reset to factory settings.

With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks two colors, and now you have reset to factory settings.

To reset your JBL Tuner simply Long press Volume+ and Bluetooth button for 5-7 seconds. Your Tuner is now successfully reset and you can Bluetooth pair with it again.

There is a reset button on the bottom of the Omni+ devices. Press and hold this button for 5 seconds to perform a factory reset of your product. All product settings, Wi-Fi, and Bluetooth connections will be erased. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.

The reset procedure is quite different from the rest of the OMNI+ series. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.

On the back of your OMNI BAR+ there is a reset button. Hold it down for 5 seconds, until the round button LED lights up in white. The product is now reset and ready to be set up again.

Press volume + and volume - simultaneously for 5 seconds to reset.
The headphone must be ON while doing this.

Press and hold the Source, Vol+ and Vol- buttons at the same time until you see the text "reset" on the soundbar's display.

With the Onyx Studio 2 switched ON, the ON/OFF switch light flashes while the unit is charging. If the unit is switched OFF, no indication shows that charging is taking place, but charging still takes place. When charging is complete, the light becomes constant. There is no battery status indication, so it is not possible to follow the power level of the battery.

The charging LED stops lighting white, and goes dark.