How To
How To
1863 results
-
You will get a notification or if you go to the System section, and the software button is highlighted with "Download Firmware", you can download and install the firmware.Was this helpful? Thank you for your feedback!
-
You will get a notification or if you go to the System section, and the firmware button is highlighted with "Download Firmware", you can download and install the firmware.Was this helpful? Thank you for your feedback!
-
As the headphones are charging, you will see a red solid light indicator at the bottom LEFT ear cup. Once the unit is fully charged, the red light will turn off.Was this helpful? Thank you for your feedback!
-
You will hear an audio prompt to readjust the position of the left ear piece stating “heart rate not detected, adjust ear bud position”. The sensor is also in the correct position when the green LED light is not visible from the outside of your ear.Was this helpful? Thank you for your feedback!
-
By habit, we try to shove earbuds into our ear canals in attempts to get them to stay in. The 500 Series headphone is a completely different concept. The tip of the enhancer (ear tip) should funnel gently down into the ear canal and the base of the enhancer should fill the entire concha (bowl) of your ear. If there is still quite a bit of space between the back of the enhancer, and the back of the bowl of the ear, there is nothing to support it and it will eventually fall out. Typically larger sizes will fill the extra space inside the concha. We recommend trying both sizes featured in the packaging. If you are still experiencing fit issues, please reach out to your local JBL Customer Support for information regarding different sizing options.Was this helpful? Thank you for your feedback!
-
You can check on the JBL QuantumENGINE Spatial Sound page or check whether the Spatial Sound slider on top is onWas this helpful? Thank you for your feedback!
-
Select the UA Sync icon in the upper right hand corner of the dashboard. If your headphones are connected, they will appear under "My Apps and Devices". Tap on "UA Sport Wireless Heart Rate" and you will see your headphones settings. Your headphones' battery life appears in the top left corner. If you have an IOS device, you also will be able to see the battery life indicator in the upper right hand corner next to the BT symbol. Additionally, you should hear the audible voice stating ‘low battery’ when you have 15-20 minutes left of battery life left on the headphones.Was this helpful? Thank you for your feedback!
-
The Flip 3 SE has 5 white leds which shows the battery level when you power on the device. Each white led indicates around 20% battery level. When all of the white leds are off, and the last led is blinking red, you should recharge the battery.Was this helpful? Thank you for your feedback!
-
When the headphones are charging, you will see a solid red light at the top of the inline microphone. When the headphones are fully charged, the red light will shut off. You should expect 8 hours of playback time. Please keep in mind that the level of volume can effect the longevity of the battery life.Was this helpful? Thank you for your feedback!
-
After you set up Alexa and Google Assistant via the JBL One app, you will see examples of what you can do with each assistant. For more information on what each voice assistant does, visit Alexa Features or Explore Google Assistant
Was this helpful? Thank you for your feedback! -
1.) Provide presets to user via Dropbox, email, etc. Each preset consists of 4 files, where X is the preset number: • config_X.ogf • config_X.xml • config_X.xml.cmt • config_X.light.ogf 2.) Have user create on USB the following directory tree: /Trinnov_Optimizer/jbl/preset 3.) Copy preset files to the preset directory (may also include microphone directory) 4.) Connect USB to a USB slot on rear of SDP-75 The USB menu appears 5.) Select “Load Presets from USB Key” 6.) (optional) Select “Load Microphone Files from USB Key” To add single cal mic (from Kevin’s system) 7.) (optional) Select “Load Profiles from USB Key” if adding preset configurations( if they are also placed on USB key) Extra notes If the target preset should be a different number, the preset number can be renamed prior to loading USB key into unit.Was this helpful? Thank you for your feedback!
-
Tap once on the JBL logo of the right earbud, then place your finger on the logo again, and hold it there for 5 seconds. You will hear a confirmation tone in the headphones when locking takes place. To unlock, close the power hook.Was this helpful? Thank you for your feedback!
-
To ensure the best accuracy, it is important that you are using the proper size and the headphones securely fit in the ear. Please reference FAQ: How do I find the proper fit? to make sure you are wearing them correctly. You should also make sure that the enhancers are properly installed on the ear buds so that material is fully stretched over the bud and the window for the heart rate (HR) sensor is not covered. Please reference FAQ: How do I switch enhancer sizes? for more guidance. Once you've found your ideal size and ensure they're installed correctly, make sure the HR sensor is on. When it is on, you will see a green light on the LEFT ear bud and should hear the audio prompt stating, “Heart Rate sensor on”. For best results, insert the earphone into your ear so that the green heart rate sensor on the LEFT ear bud is fully hidden inside the ear (behind your tragus). Double check that the ear bud is touching the back of the bowl of your ear for the most accurate signal - this is often times achieved by using the largest size that fits comfortably in your ear. Lastly, the ear loop should not be pushed backwards to align with arc of the ear perfectly; it is likely there will be negative space between the headphone loop and your ear. You should hear the audible alert telling you if the ear bud needs to be adjusted if it is unable to retrieve a proper reading on your heart rate. Heart Rate accuracy can vary depending on the type of exercise you are performing; it is recommended for steady state endurance-oriented activities to ensure best accuracy. While the technology is state-of-the-art, there are limitations that may cause some readings to be inaccurate under certain circumstances. These circumstances include physical characteristics, fit, and the type of activity as outlined above. The heart rate monitor data is not intended to be used for medical purposes, nor is it intended to diagnose, treat, cure or prevent any disease or condition.Was this helpful? Thank you for your feedback!
-
During phone call, short press the Siri Access button shown in “quick start guide” section 6 to mute the microphone. A short press the same button again will un-mute.Was this helpful? Thank you for your feedback!
-
The HD 3700 will list each folder or directory together. Folders that are found in different directories can be easily navigated to using the FOLDER +/- button. Simply press the FOLDER +/- button to skip between different directories.Was this helpful? Thank you for your feedback!
-
Short-press the Bluetooth Button to activate pairing mode. Now set your device to scan for Bluetooth devices. It will find the BOOST TV and allow you to pair to it.Was this helpful? Thank you for your feedback!
-
Short-press the Bluetooth Button to open for new pairing.Was this helpful? Thank you for your feedback!
-
Swift Pair is the newest way to pair your Bluetooth peripherals Windows 10, version 1803 or above.
Steps:
1. Put the Bluetooth peripheral in pairing mode
2. When the peripheral is nearby, your Windows device will show a notification
3. Selecting “Connect” starts pairing the peripheral
4. When the peripheral is no longer in pairing mode or is no longer nearby, your Windows device will remove the notification from the Action Center
Was this helpful? Thank you for your feedback! -
Hold the Power ON/OFF button down for >5 seconds. Status light will pulse White when headphones are in pairing mode. Release. Access Bluetooth settings on your source device. Locate "№ 5909" and connect. A solid white light indicates you are connected.Was this helpful? Thank you for your feedback!
-
1. Enter pairing mode and connect to device 1. 2. Enter pairing mode again and device 1 will disconnect. 3. Connect to device 2 and turn headphone off. 4. Turn headphones on and headphones will automatically connect to device 1 and 2 simultaneously. 5. Pause one device and play from the other to swap headphones connection. NOTE: Maximum number of devices that can be connected at any given time - 2 source devices.Was this helpful? Thank you for your feedback!
-
Simply hold Bluetooth button on the remote and once its start flashing, on your device go to your Bluetooth settings and look for the gtr amp and pair it.Was this helpful? Thank you for your feedback!
-
The SB450 soundbar is paired to the subwoofer right out of the box. If the 2 parts are not already paired together, simply press the Pairing buttons on the rear panel of both products and they will connect with each other.Was this helpful? Thank you for your feedback!
-
Power on the Flip 3 SE and press the Bluetooth button. The Flip 3 SE should be available in the list of Bluetooth devices on your mobile phone/tablet.Was this helpful? Thank you for your feedback!
-
Normal pairing is automatic, and happens when you first switch both devices on. If pairing does not take place automatically, or you have to force new pairing, here is what to do: Turn on the soundbar and the subwoofer. If the connection is lost, the LED indicator on the subwoofer blinks slowly. Second, press the CONNECT button on the subwoofer to enter pairing mode. The LED indicator on the subwoofer blinks quickly. Third, press and hold the DIM DISPLAY button on the remote control for 5 seconds, followed by short press on BASS+, and BASS- button in sequence. Panel display will show “PAIRING”. If pairing succeeds, the LED indicator on the subwoofer lights up, and the soundbar display will show "DONE”. If pairing fails, the indicator on the subwoofer blinks slowly. Lastly, if the pairing fails, repeat the steps above. If you have continued trouble performing the pairing, please try to switch off all wireless devices in the home, then try again. This means routers, TV sets with wireless functions, telephones, computers etc. Since overcrowding on the 2.4 GHz frequency now often causes problems, eliminating all this activity makes space for the Bar to establish its connection, and you should be able to pair without problems. Afterwards, you can switch your devices on again. Often, all will now work fine, and if not, you will know which devices are doing the interference.Was this helpful? Thank you for your feedback!
-
To pair to a different device, double tap and hold your finger on the JBL logo for 5 seconds until you see the LED light flash blue. Make sure that the device you are trying to connect to is in range and in pairing mode. You should see the Endurance headphone pop up on your discoverable devices within a few seconds and the flashing LED light should now be a solid blue.Was this helpful? Thank you for your feedback!
-
Power on the Soundgear and press and hold the Bluetooth located next to the power button on the right arm. Once you press the the bluetooth button, you will see a fast blinking LED light as it attempts to pair to a different device. You will also hear the audible chime as it attempts to Make sure the device you are attempting to connect to is on and in pairing mode. The JBL Soundgear should be displayed on your discoverable devices within a few seconds. Choose the JBL Soundgear and you should now be connected!Was this helpful? Thank you for your feedback!
-
In order to pair to a different device, make sure the headphones are turned off. Proceed to press and hold the power button located on the LEFT arm of the neckband. You will hear the audio voice prompt state, “powering on” Continue to press and hold the power button for 3-5 seconds or until you hear the voice prompt state, “looking for device.” Make sure that the device you are attempting to connect to is in the Bluetooth search mode and within range. UA | JBL Flex should appear on your device within 3-8 seconds. Once you choose this option on your discoverable devices, it will connect and the voice prompt will state “Connected”Was this helpful? Thank you for your feedback!
-
On the Right ear cup, slide the bluetooth button towards the down position and hold until you see the fast blinking blue LED light. Make sure that the device that you are trying to connect to is in pairing mode. It should recognize the N60NC Wireless within a few seconds. You should here the audio "chime" when it is connected and the LED should change to a slow blinking light.Was this helpful? Thank you for your feedback!
-
1. Place the 3770 in Bluetooth input mode with the BT button on the front panel or the remote. 2. Do a BT search on the phone, until you find HK3770. Then pair with it. 3. Now you can select the HK3770 as audio source on your phone, depending on the phone. On some phones, you can simply begin to play music after performing the pairing, and the HK3770 will play, if it is in Bluetooth input mode, shown on the front panel display. 4. You can control play/pause etc. from either your phone or from the HK3770 remote control. If you want to use the HK3770 remote, you must first press the STEREO Button on the remote control in order to activate the correct remote codes. Now a press on the PAUSE Button on the HK3770 remote will pause the music by placing your phone on pause, and you can restart play by pressing the PLAY Button. 5. To pair another source to HK3770, first deactivate BT on the source presently paired to release new pairing.Was this helpful? Thank you for your feedback!
-
Press and hold the center button on the inline microphone located below the right earpiece. It helps to have one of the ear inserts in your ear to listen to the audible voice prompts. If this is your first time using the headphones, the headphones will automatically go into search mode. You will hear the audible voice stating, “power on” followed by “looking for device”. To power off, press and hold the center button on the inline microphone until you hear the audible voice stating, “power off.” The flashing LED light should change to a solid red light before completely turning off.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call Us now at:
(877) 871-6755
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat with Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)