How To
How To
1413 results
-
To increase battery life on your Quantum headphones, turn off your RGB lighting as this will help increase the wireless playback time. You can turn off the RGB in the QuantumENGINE or press and hold the mute button on the headset.Was this helpful? Thank you for your feedback!
-
Reset the Soundbar by the same process as when doing "reset remote settings": 1. Switch the SB 350 ON. 2. Press and hold the Surround and Volume (–) buttons simultaneously for about 3-4 seconds, then let go. The Source selection Button flashes amber, followed by the power button and source buttons flashing several times. 3. The soundbar is now reset.Was this helpful? Thank you for your feedback!
-
If you are experiencing issues when setting up your HK Citation Oasis to your WiFi network using the Google Home app, then please turn Bluetooth off on your phone, then turn Bluetooth back on again and try the setup again.Was this helpful? Thank you for your feedback!
-
The intensity of the light show is dependent on the amount of audio signal being sent into the unit.
If you are experiencing a light show that doesn't move around very much, it is likely that you are not using a feature on your phone called Bluetooth Absolute Volume*. This means that the volume of your phone/tablet/device is controlled independently from the volume of the speaker.
So, if you have the Pulse 4 set to maximum volume or close to it, but the volume on your device is set at a low level, the light show will show little to no effect. All you have to do is reverse it. Turn up the volume on the device to the maximum and set the Pulse 4 to the desired volume. This will send the correct level to the speaker and the light show will show plenty of effect. This also benefits the sonic quality as well. Therefore, we recommend always having the volume on your device turned up to a high level and then adjusting the volume level on the speaker itself. This way you'll be able to enjoy the light show while also getting good audio quality. Or, if possible, setup your device for Bluetooth Absolute Volume*.
*BLUETOOTH ABSOLUTE VOLUME: Most phones/tablets/devices now use Bluetooth Absolute Volume (a.k.a. volume sync) by default. This is a feature that synchronizes the volumes of the device and the speaker, and allows the speaker volume to be controlled by changing the volume on either the device or the speaker. The volume being sent from the device is fixed at full volume.Was this helpful? Thank you for your feedback! -
A new firmware version has been released for the Pulse 4 (Version 0.5.1.0), below is a list of the improvements:
- Supports Bluetooth 5.1 profile.
- Improves the stability of stereo setup using the JBL Portable* app.
- Improves compatibility with Mac computers.
- Enhances light show synchronization with music.
- Download and install the JBL Portable* app from the Google Play/App Store.
- Connect your Pulse 4 to your phone/tablet through Bluetooth.
- Open the JBL Portable app and wait for the Pulse 4 to appear.
- On the Pulse 4 screen, select settings (gear cog symbol).
- Proceed with installing the firmware update.
*JBL Portable is the new name for the JBL Connect app, the name will change in January 2021.Was this helpful? Thank you for your feedback! -
Press and hold the Light Show & Bluetooth buttons together for > 2 seconds.
Was this helpful? Thank you for your feedback! -
QUANTUM 910
Software Update Release Notes
------------------------------------------------------------------------
Version: 3.3.0
Release Date: April 9th, 2025
Release Media: OTA (over the air) Update via JBL Quantum Engine
What’s New
- Stability and performance improvement
Was this helpful? Thank you for your feedback! -
QUANTUM STREAM STUDIO
Software Update Release Notes
------------------------------------------------------------------------
Version: 1.4.9
Release Date: January 13th, 2025
Release Media: OTA (over the air) Update via JBL QuantumENGINE
What’s New
- Zoom USB Certified
- Stability and performance improvement
Was this helpful? Thank you for your feedback! -
QUANTUM STREAM TALK
Software Update Release Notes
------------------------------------------------------------------------
Version: 1.4.9
Release Date: January 13th, 2025
Release Media: OTA (over the air) Update via JBL QuantumENGINE
What’s New
- Zoom USB Certified
- Stability and performance improvement
Was this helpful? Thank you for your feedback! -
It is not possible to have Ambient Aware or TalkThru activated at the same time as Sidetone when the microphone is turned on during a call. This is the case no matter if you are using Bluetooth or the 2.4 GHz mode.
You can use Ambient Aware during a call if Sidetone is turned off. You are able to do this in both Bluetooth or the 2.4 GHz mode.
All three audio modes are activated if the microphone on your device is turned off no matter if you are using Bluetooth or the 2.4 GHz mode.
Was this helpful? Thank you for your feedback! -
No, that is not possible. However, you can create a 5.1 wireless surround system to extend your TV or movie sound. All you need is two additional OMNI+ speakers, such as 2 x OMNI 10+, OMNI 20+ or OMNI 50+.Was this helpful? Thank you for your feedback!
-
To skip the tracks forward, press and hold the volume up (+) button for 1-2 seconds and you will advanced to the next song. To start the current song you are listening to over, press and hold the volume down (-) button for 1-2 seconds. Please note: You can only advance to the next song be skipping forward, you cannot skip tracks backward. You can only restart the current song over by pressing the volume down (-) button.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Message Us
Chat with a support agent via Whatsapp at:
91 70658 44446
Mon - Sun: 10:00 am - 7:00 pm (IST)