How To
How To
1413 results
-
Find a paper clip or something similar, then next to the power connection there is a small hole. Insert your paper clip and hold it until the Harman Kardon Allure tells you it is reset.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press VOLUME + and VOLUME - , and hold them for 5 seconds. Your headphones are now reset to factory settings. This is true for Everest 310, 710, Elite 750, 310GA and 710GA.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold both volume buttons for more than 5 seconds.
Your headphones are now reset to factory status.
Was this helpful? Thank you for your feedback! -
In order to reset the Charge 4, with the unit on, press “Volume+” and “Bluetooth” at the same time for 3-4 seconds until you hear the audible chime.Was this helpful? Thank you for your feedback!
-
Power ON the device, then press and hold the "Volume+" and the "Play/Pause" buttons at the same time. When the device switches off after a few seconds, sounding the OFF prompt, it has been reset.Was this helpful? Thank you for your feedback!
-
For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.
Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.Was this helpful? Thank you for your feedback! -
The charging LED on the headset will flash red when the battery is low. For the ELITE models, a more accurate indication of remaining battery time can be seen on the fuel gauge in the app.Was this helpful? Thank you for your feedback!
-
The L and R that indicate the two channels are located on the soft grommets that protects the signal cable where it enters the headphone shell. The letters are recessed into the grommets, and are very small. If they are too difficult to read, it may be easier to simply observe how the headphones are situated in the ears. The oval body of each in-ear, with the chrome stripe, should be away from the head, and be situated in the ear lobe, not stick out directly from the head.Was this helpful? Thank you for your feedback!
-
While charging, the charging indicator diode is lighting constantly. When charging is complete, the light goes out.Was this helpful? Thank you for your feedback!
-
When less than one hour's capacity is left, the red diode will blink. It will eventually stop blinking, when all power is gone.Was this helpful? Thank you for your feedback!
-
In the Harman Kardon Controller app, set up the Adapt as a stand-alone room, not a stereo pair room. The Adapt always delivers stereo audio via its Audio Out jack.Was this helpful? Thank you for your feedback!
-
To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.Was this helpful? Thank you for your feedback!
-
To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.Was this helpful? Thank you for your feedback!
-
The track control button is located in the center of the inline microphone. This also serves as the pause/play button and enables you to answer and hang up phone calls. Two quick clicks on the center button will skip the tracks forward to the next song. Multiple quick clicks will skip the tracks backward. Compatibility may vary with some older phone models.Was this helpful? Thank you for your feedback!
-
Two quick clicks on the microphone will skip the track forward. Three quick clicks on the microphone will skip the track backward to the previous song.Was this helpful? Thank you for your feedback!
-
The best way to remove the enhancer from the ear bud is to gently pull back the outer rim of the enhancer that is located around the base of the ear bud. When replacing the current enhancers with a different size, please make sure to align the funnel of the enhancer tip over the small speaker screen of the headphone casing. The LEFT enhancer will feature the square cut out that allows you to receive your Heart Rate reading. It is important that the small digital square on the ear bud is fully exposed and the enhancer cut out is placed around it and not over it. If the enhancer is not attached properly, you will hear the audible voice stating that it cannot receive an accurate reading on your heart rate and you will need to readjust the enhancer.Was this helpful? Thank you for your feedback!
-
The on/off button is a spring-loaded slider button. Press the button upwards against the spring pressure, and hold it there for about three seconds. Now you will hear the "off" prompt sound in the headphone speakers, and the LED light goes out. Now the headphones are switched off. Please note that if you do not play music or press any button for about 10 minutes, the headphones will switch off automatically.Was this helpful? Thank you for your feedback!
-
Every TV is different, but most current TVs will let you turn off your internal TV speakers in the Settings menu under the Audio section.Was this helpful? Thank you for your feedback!
-
Every TV is different, but most current TVs will let you turn off your internal TV speakers in the Settings menu under the Audio section.Was this helpful? Thank you for your feedback!
-
Press and hold the center button for 3-5 seconds until the audible voice states “power off” you will briefly see a red light before it completely powers down.Was this helpful? Thank you for your feedback!
-
It is not possible to turn the Google Assistant feature off on the headphones, but if you turn off GA on your phone, the headphones won't trigger. On the Everest GA models, the Google Assistant feature is in fact than an extension of your phone, so once you connect to your phone via BT, when you touch the right ear pod, it commands your phone to open the "Hey Google" command.
The only way to stop that from happening is to change the Google settings on your phone to deactivate Google Voice Match, or deactivate Google Assistant entirely.
Was this helpful? Thank you for your feedback! -
To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the UA WIRELESS headphone. Once you select that option, the audible voice should state, “connected”.Was this helpful? Thank you for your feedback!
-
To activate Bluetooth pairing mode, please follow these steps:
- Press the Bluetooth button on the bottom of the right headphone.
Was this helpful? Thank you for your feedback! -
1. First pair your phone to the Boost TV. You can test this by streaming music to the product. 2. Then press the TV button to switch to the TV sound. Press the TV button again so the LED light is blue--Blue LED means that SoundShift is ON. 3. When you press PLAY on your phone, then you will hear your Bluetooth audio break in over the TV sound. This confirms that SoundShift is working. 4. Simply press SoundShift button again, this will now turn OFF the SoundShift. Now you can watch TV without any interruption from Bluetooth devices.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Message Us
Chat with a support agent via Whatsapp at:
91 70658 44446
Mon - Sun: 10:00 am - 7:00 pm (IST)