No, that is not possible. However, you can create a 5.1 wireless surround system to extend your TV or movie sound. All you need is two additional OMNI+ speakers, such as 2 x OMNI 10+, OMNI 20+ or OMNI 50+.

QUANTUM 910

Software Update Release Notes

------------------------------------------------------------------------

Version:  3.3.0

Release Date: April 9th, 2025

Release Media: OTA (over the air) Update via JBL Quantum Engine

 

What’s New

1. Stability and performance improvement

Press and hold the Light Show & Bluetooth buttons together for > 2 seconds.

Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.

The JBL Quantum 200 is compatible with PC, PlayStation, Xbox, Nintendo Switch, Mobile, Mac and VR.

The JBL Quantum 100 is compatible with PC, PlayStation, Xbox, Nintendo Switch, Mobile, Mac and VR.

PARTYBOX ULTIMATE

Software Update Release Notes

------------------------------------------------------------------------

Version:  24.15.37.70.00

Release Date: April 17, 2024

Release Media: OTA (over the air) Automatic Update

 

What’s New

1. Stability & performance improvement

------------------------------------------------------------------------

Version:  23.50.23.70.00

Release Date: December 29, 2023

Release Media: OTA (over the air) Automatic Update

 

What’s New

1. Fixed microphone distortion issue when being used in Daisy Chain Mode
2. Software Update optimized

It is possible to pair two of the same model of JBL PartyBox speakers together through TWS (True Wireless Stereo) mode.

PartyBox On-The-Go/100:
Connect just the left PartyBox with the chosen device first, with the right PartyBox turned off. The speaker that is connected first will automatically be the left channel. Now turn the right PartyBox on and continue with TWS pairing (detailed below).

PartyBox 200/300/1000:
A button (L/R) on the rear of the speakers is used to assign the correct channel to the speakers after pairing is made.
In order to activate TWS mode, press and hold the Bluetooth button on the first speaker until the notification chime sounds, about 5 seconds. Then press and hold the Bluetooth button on the second speaker until the notification chime sounds (as seen below). TWS mode is now activated. To disable TWS, press and hold the Bluetooth button on either speaker, or power off one speaker.

Partybox 110/310/710/Encore/Essential:
Press the buttons labelled TWS on both speakers to connect the speakers in TWS mode (pictured in item 2 in the image below, with two speakers on the button).

TWS can be activated and deactivated remotely in the JBL Partybox app, in addition to assigning the left and right channels to the correct speakers.
Once the TWS connection is setup, it will be in Stereo mode by default if both speakers are the same model, otherwise the speakers will be in Party mode by default if different Partybox models are used. You can also switch between Stereo and Party mode in the JBL PartyBox app if two of the same Partybox models are used.

Please note: In order to achieve TWS mode, the speaker must be the same model with the exception of the PartyBox 200 and PartyBox 300 which can be paired together via TWS. You cannot achieve TWS with a PartyBox 1000 and a PartyBox 300. You cannot achieve TWS with a PartyBox 100 and PartyBox 200. However, it is possible to connect a maximum of two of either the Partybox 110, 310, 710 or Encore/Essential together in Party mode - the two speakers then do not need to be the same model, but Stereo mode will not be possible.

- Try to disconnect some devices from your Wi-Fi network. Some routers may have weak performance, which can cause issues and poor connection to all devices in your network. - If your router supports 5Ghz ( 802.11N or AC ) and you have devices that are capable of using 5 GHz Wi-Fi then switch to that specific network for best performance. - If you have a lot of ( Legacy / older than 5 years ) devices on 2.4GHz network, try limiting them to max. 6 connected simultaneously

What you need first

Make sure that the device is installed on your Wireless network, by ensuring these steps below:

1. You have the most recent version of the Google Home app installed 
2. Your Citation device is powered on
3. Your Citation device is plugged into a wall outlet.
4. The Citation device is located near your router 
5. The white LED lights in front of the Citation device are blinking 
6. If you are using an Apple iOS device, you need to turn on Bluetooth to installed the device.

   1. On your iOS device Home screen, tap Settings > Bluetooth 

   2. Make sure Bluetooth is on
   3. Return back to the Google Home app 
   4. Your Citation device should appear as "Set up this device"
7. If you are using an Android device, you need to turn on Bluetooth and Location Services.
   1. On your Android device, tap Settings.
   2. Find Bluetooth settings > Make sure Bluetooth is on
   3. Tap Location > Turn on location 
   4. Tap Settings > Apps > Google Home app > Permissions.
   5. Next to "Location",  check the slider is on.
   6. Your Citation device should appear as "Set up this device" .

If you are still having trouble discovering your Citation devices in the Google Home app, follow the steps below for further troubleshooting.

Troubleshooting

Step 1. Reboot your Citation device 

1. Disconnect the power cable from your Citation device 
2. Reconnect power cable to your Citation device 

Step 2. Force close and relaunch the Google Home app      

1. From your Apple iOS device, do the following below:                   
   1. Press the Home button two times quickly. There will be a small preview of your recently used apps.      
   2. Select the app you want to close and swipe up towards the top of the screen.
   3. Launch the Google Home app again.        
2. From your Android device, do the following below:              
   1. Launch the Recent Applications menu to see small previews of your recently used apps. The Recent Apps button, a square icon, should be accessible at nearly any time along the bottom of the screen along with the other buttons on the virtual task bar.
   2. Select the app you want to close and swipe left or tap the X.
   3. Launch the Google Home app again.

 

Last thing to try​ 

If you are still experiencing issues with your Citation device not connecting to your Wireless network, try the following:

1. Try finding another mobile device to set up your Citation device, sometimes it can help connecting your speaker 

2. Relocate your Citation device, or try to disable other Wireless network devices that might cause interference for your Citation device.

3. Perform a factory reset of your device, by holding down the reset button for more than 5 seconds.
4. Reboot your Wireless router           
5. Lastly, try turning Wi-Fi off and then back on again on your mobile device. Reopen your Google Home app and try again.

The JBL Xtreme will no longer appear in the JBL Portable app while using Apple devices with iOS 14 or later installed, due to incompatibility. 
You can continue to use the speaker as normal with these devices through Bluetooth or Aux connection, but it will no longer appear in the app. 
There are currently no plans to release a new Firmware as the JBL Xtreme has been discontinued. 

Make sure the volume control on the headset is turned up. Rotate the volume wheel on your headset to increase the volume. If you're connected to the PC via USB, check that the default device is selected under Control Panel > Sound > Playback. Select JBL Quantum 600 or Quantum 800 Game, right-click, and select "Set as Default Device". Check your headset's game-chat balance dial and ensure that the balance is correct. Check the JBL Quantum 600 or Quantum 800 Game device and make sure it is not muted or turned all the way down.

Make sure the headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. Check that the correct playback device is selected under Control Panel > Sound > Playback. Select the correct device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.

Make sure the headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. If you're using the USB dongle, check that the correct playback device is selected under Control Panel > Sound > Playback. Select the proper playback device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.

Ensure that the correct device is selected as the default device under Control Panel>Sound>Playback. Make sure the on headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. Check that the correct playback device is selected under Control Panel > Sound > Playback. Select the correct device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.

Some mobile phones, tablet computers or laptop computers will react to the powerful magnetic field from the loudspeaker drive units that are right beneath the top panel. Some have magnetic sensors built in, which means that covers with magnets in the lid can turn the phone ON when the cover lid is opened, and turn it OFF again when the lid is closed. Such phones may turn off if placed on certain portions of the top panel. Other devices are simply sensitive to magnetic fields. You can move the device around on the top of your L8 or L16 speaker, to check if some locations are better than others. The magnetic fields are most powerful near the front panel, where the speaker units are mounted. If you cannot find a location which works, your particular phone, tablet or laptop cannot be used while resting on the top panel of your speaker. There are no reports of damage to any devices because of this phenomenon.

Do not worry, pairing both devices is easy and quick. Press the "pairing" button on the back of the Omni Bar, then press "pairing" button on the subwoofer. They will start communicating with each other, and when both devices show white light in the LED on the back, that indicates that they are paired.

One explanation can be that your OMNI 50+ is part of a 5.1 system with your Omni Bar, which will make the surround OMNI 50+ left and right rear speakers act as "secondary", and Bluetooth connection is not possible to secondary speakers. To use the OMNI 50+ as a portable speaker again, simply perform a reset of the speaker by pressing the reset button for 5 seconds. Please note that after resetting your OMNI 50+, it is no longer part of the 5.1 wireless system.

Dual band routers that have 2.4 and 5 GHz connection bands. If devices connect on different bands, they cannot see one another. Please make sure your phone and speakers are both connected to 2.4 GHz or 5 GHz and that there is no AP isolation activated between them.

If your Wi-Fi network name has special characters, such as (, `, \, ', ", or ), then please change the name of your Wi-Fi network, as these characters are not supported. After changing the name, you can go ahead and setup the speaker to your Wi-Fi network.

No, since the speaker does not store any information locally. To remove all settings from your stolen device, simply unlink the speaker from your account, and the next time the speaker goes online it will not connect to your account. However, if you have used the command ""Remember this"" feature, please beware of sensitive information, as the speaker will inform you of whatever you have asked it to remember. But after unlinking the speaker, it will forget.

1. Insert both earbuds into the charging case.
2. Try to click 5 times on both left and right earbuds button simultaneously, to reconnect left and right earbuds.
 

If the wireless mic is out of signal range, you will experience drop outs or no sound. Once range is reestablished, the speaker should automatically detect the mic and resume connection within less than 3 sec. 

When a wireless mic is connected, the speaker will play a notification sound once. If two wireless mics are connected at the same time, there may be a 1 sec gap between the two notification sounds. 

If one of the wireless mics is not working, we recommend the following: 

1. Turn off the speaker
2. Turn on the mic and place it on top of the speaker
3. Turn on the speaker
4. The speaker should automatically pair with the new mic within 3 min and play a notification sound 
 

Yes. You can configure the volume of the mic monitoring in JBL QuantumENGINE. The default setting of the mic monitoring is "OFF”.

Yes. You can configure the volume of the mic monitoring in JBL QuantumENGINE. And the default setting of the mic monitoring is set of “OFF”.

The speaker is IPX5 certified, it can withstand direct splashes from any direction for up to 3 minutes. Although a little snow or rain won't hurt it, we do not recommend keeping the speaker outside during rain and/or snow. Also be aware of extreme hot or cold temperatures, they may be damaging.

The Left and Right bud should sync together automatically when removed from the case. If the Left and Right bud do not sync together automatically within 15 seconds, you may manually sync the buds together. With the buds out of the case, press the center button on each bud 3x. This action does not have to be done simultaneously. You may start with either the L or R bud to initiate syncing.

The Checklist

Let us walk-through a list of things needed to ensure every requirement is met.

1. Check your mobile device if that is able to connect to same Wireless network.
2. Make sure you are within range of your Wireless router.
3. Check the Wireless signal on your mobile device, does it have a weak signal then move closer to the router.
4. Try both Wireless network bands 2.4GHz and 5GHz in case one of them are failing.
   1. You will have longer range with 2.4GHz, but less performance and most of the times a crowded network (many devices are using 2.4GHz band).
   2. You will have less interference with 5GHz and higher performance, however, the range of the 5GHz network has shorter range.
5. Try using a different mobile device, if you have one.
6. Reboot your Wireless network router and your mobile device.

Watch the video below for help with setting up your Google Assistant device.

Wireless Network Extender

Some houses or apartments can be too big for one Wireless network router to cover it all.
Let's talk about the issues that might appear with an Extender network.

1. Network Extenders that will help cover poor signal in your home, often results in poor connection and low speed performance.
2. Often the Network Extender is a low budget device or not suited for having too many devices attached to it.
3. Placement of the speaker is crucial as you can put it in a place where it could connect to either main Wireless router or the Extender, that will confuse Wireless network devices.
4. To solve this issue, try move the speaker closer to main router or have fewer devices attached to your Wireless Extender.
5. In addition, always use 5GHz connection between your Network extender and main router (best solution and performance).

One Wireless Network Name (SSID)

1. You may have set the Wireless Network SSID (Wi-Fi network name) to one big Wireless network (With a main router + Extender(s).
2. If the JBL LINK device is within range of both Wireless networks (Main router & Extender) then it can get confused with which one to connect to.
3. To solve this issue, using two different name for your extended network will help with the performance of the JBL LINK Speaker and Google Assistant request.

 

The Checklist

Let us walk-through a list of things needed to ensure every requirement is met.

1. Check your mobile device if that is able to connect to same Wireless network.
2. Make sure you are within range of your Wireless router.
3. Check the Wireless signal on your mobile device, does it have a weak signal then move closer to the router.
4. Try both Wireless network bands 2.4GHz and 5GHz in case one of them are failing.
   1. You will have longer range with 2.4GHz, but less performance and most of the times a crowded network (many devices are using 2.4GHz band).
   2. You will have less interference with 5GHz and higher performance, however, the range of the 5GHz network has shorter range.
5. Try using a different mobile device, if you have one.
6. Reboot your Wireless network router and your mobile device.

Watch the video below for help with setting up your Google Assistant device.

Wireless Network Extender

Some houses or apartments can be too big for one Wireless network router to cover it all.
Let's talk about the issues that might appear with an Extender network.

1. Network Extenders that will help cover poor signal in your home, often results in poor connection and low speed performance.
2. Often the Network Extender is a low budget device or not suited for having too many devices attached to it.
3. Placement of the speaker is crucial as you can put it in a place where it could connect to either main Wireless router or the Extender, that will confuse Wireless network devices.
4. To solve this issue, try move the speaker closer to main router or have fewer devices attached to your Wireless Extender.
5. In addition, always use 5GHz connection between your Network extender and main router (best solution and performance).

One Wireless Network Name (SSID)

1. You may have set the Wireless Network SSID (Wi-Fi network name) to one big Wireless network (With a main router + Extender(s).
2. If the Wireless speaker is within range of both Wireless networks (Main router & Extender) then it can get confused with which one to connect to.
3. To solve this issue, using two different name for your extended network will help with the performance of the Wireless connected speaker and Google Assistant request.

 

You can clean it by wiping it gently with a damp cloth. Take extra care not to let water leak into the speaker chamber, as it will damage the speaker drivers.

You can adjust Equalizer, Spatial Sound, RGB LED effects, change microphone settings and update the headset's firmware

You cannot download the JBL Portable App on a PC. This app is only available on mobile devices.

The JBL Free X does not feature volume control. In order to adjust the volume, you must manually increase/decrease from your device.

In the event that ear pieces do not re-pair automatically to paired Bluetooth device, power off ear pieces individually by press and hold the buttons for 5 seconds. To enter Bluetooth pairing mode when ear pieces are powered off, press and hold on buttons of both earpieces for 8 seconds. Re-pair the right ear piece with desired Bluetooth device when LED indicator on right ear piece alternates between blue and white LED lights.

In the event that left and right ear piece pairing is lost, power on both ear pieces and press the buttons 3 times on each ear piece to initiate re-pair.

The JBL Free automatically switches from stereo to mono when making or taking phone calls. Voice calls will only come through the right ear piece for a more natural call experience.

When you place the two Free earphones in the charging case, you will see a white led ring light up on both of them. At the same time, some of the four dot-leds on the charging case will light up to indicate the battery level of the case battery. When the earphones are fully charged, the white led ring goes out on each of them. When both are fully charged, the charging case charging level leds go out too.

Please use an OBD II extension cable in this case. An extension cable is not included in the package but they are readily available for purchase on-line.

Please check with your car manufacturer to ensure your car supports CAN or K-line. JBL DRG only works with CAN and K-line to get the engine data for engine sound simulation. If your car does support CAN or K-line, please launch the JBL DRG app and check the engine sound volume bar (the right column with button marked with “E”) in the “Sound Mode” section to make sure it is not turned off.

This headphone does not feature volume control. You must manually control volume from your device.

Yes, the Xtreme 2 features an IPX 7 rating. IPX7 is defined as the speaker can be immersed in water up to 1 meter for up to 30 minutes.

No. The 600BTNC headphone does not feature any IPX rating that protects it against sweat or water. Over exposure to water can compromise the controls on the headphones.

There is a Wi-Fi indicator on the back of the main speaker, and when it turns amber, it indicates that the Wi-Fi signal is weak. Try to move the speaker closer to your Wi-Fi router, and when the signal indicator turns White again, then it has a steady connection.

Yes, the cable has a one-button remote control and a microphone. This means that you can pause, resume play, you can pick up the phone and stop a call, and talk to other people through the microphone. There is no option to control music volume on the cable remote. That is only possible when using the Bluetooth system for wireless listening, with the volume buttons on the ear pod.

No, this cable is straight, with no remote control. The headphones have remote control buttons on the ear pods, which can be used when listening over Bluetooth wireless.

No, the app works with the ELITE models only. These are the ones that feature Active Noise Cancelling.

With the release of v.3.0 of the JBL Music app, owners of the JBL Authentics L8 and L16 are now greeted with a message that an update is available. If you own one of these speaker systems, and you know that it already supports Spotify Connect, the update firmware is already installed, and you can ignore this message. If your speaker system does not already support Spotify Connect, the update is available for you, but you cannot perform it yourself, it must go to a service center to be updated. Please contact Harman Helpdesk or the distributor in your country for advice regarding servicing.

No. The Live 200BT does not feature any IPX rating so overexposure to both sweat and water can compromise the headphones.

Yes, two flexible joints permit you to expand the collar to make it easier to place it around your neck.

It would depend where you buy it from. If you bought it in Germany, it will speak German from the start and if you bought it from USA or UK it will speak English. The langauge of the speaker can be changed in our HK Alexa setup app. Go to Settings, Device, Language and select your preferred language.

No, it is compatible with PC and Mac, but not with PS4, XBOX One, Nintendo Switch or Mobile.

The JBL Flip 7 has an IP68 water and dustproof rating, meaning it's protected from water and dirt.

The speaker can be submerged in up to 1.5 meters of water for up to 30 minutes.

No. The Dual Wireless Sound featured in the Onyx Studio 5 only gives you the capability to connect to a second Onyx Studio 5. It is not possible to connect the Onyx Studio 3 and 5 together. The Onyx Studio 5 can only be connected to no more than one other Onyx Studio 5.

Actually the N5005 is very special, because it is BOTH wireless and wired, right out of the box! This is a result of its advanced design, where the cables can be removed from the speaker pods by clicking apart the MMCX connectors. The flexibility in this arrangement becomes very clear when you look at the cables that are in the box when you open it. First, there is the normal cable with 3.5 mm stereo jack and a three-button remote control. This cable is for normal sources, smartphones, tablet computers etc. There is a switch on the back of the remote that permits you to select Android/universal or iOS remote function, for total flexibility. Second, you get the Bluetooth cable, which has a battery box and a three-button remote on the cable. This cable simply converts your N5005 into a wireless headphone. AptX and AAC are supported, but not aptX HD or LL. BT transmission will not be capable of unlocking the full potential of the N5005 due to its nature as a lossy compression system, but it is nice to have this option. The cable has a chin slide lock that can secure the headphones under your chin. Playing time is up to 8 hours, and charging takes place in less than 2 hours. Third, as an indication of the high quality of audio that N5005 masters, you get a special, fully balanced cable without remote control. It uses the 4-pole 2.5 mm jack that you will find on the new generation of high-end headphone amplifiers and music players. With this connection and the proper source material and electronics, you can experience the pinnacle of music reproduction.

This model is not supported by the JBL Partybox App.

The OMNI BAR+ as standalone system is 2.1, however when using it in a 5.1 wireless surround system, it generates a virtual acoustic center speaker to complete the 5.1 Surround system. In that combination it will be a 3.1 system.

Yes, two headsets can be used simultaneously with one transmitter.

No, this is not possible. Even though the MMCX (micro-miniature coaxial) connectors seem identical, they are not the same dimensions.

While this is indeed possible, no such cable is made by AKG, so only cables from third-party manufacturers may be considered. Please note that internal pin configuration must be identical to the original cable for such a cable to work with the headphones.

Yes, Alexa has various voice commands to turn up the volume. Try saying "Alexa, turn it up" or "Alexa, set volume to 5".