Yes. You can configure the volume of the mic monitoring in JBL QuantumENGINE. And the default setting of the mic monitoring is set of “OFF”.

The speaker is IPX5 certified, it can withstand direct splashes from any direction for up to 3 minutes. Although a little snow or rain won't hurt it, we do not recommend keeping the speaker outside during rain and/or snow. Also be aware of extreme hot or cold temperatures, they may be damaging.

The Left and Right bud should sync together automatically when removed from the case. If the Left and Right bud do not sync together automatically within 15 seconds, you may manually sync the buds together. With the buds out of the case, press the center button on each bud 3x. This action does not have to be done simultaneously. You may start with either the L or R bud to initiate syncing.

The Checklist

Let us walk-through a list of things needed to ensure every requirement is met.

1. Check your mobile device if that is able to connect to same Wireless network.
2. Make sure you are within range of your Wireless router.
3. Check the Wireless signal on your mobile device, does it have a weak signal then move closer to the router.
4. Try both Wireless network bands 2.4GHz and 5GHz in case one of them are failing.
   1. You will have longer range with 2.4GHz, but less performance and most of the times a crowded network (many devices are using 2.4GHz band).
   2. You will have less interference with 5GHz and higher performance, however, the range of the 5GHz network has shorter range.
5. Try using a different mobile device, if you have one.
6. Reboot your Wireless network router and your mobile device.

Watch the video below for help with setting up your Google Assistant device.

Wireless Network Extender

Some houses or apartments can be too big for one Wireless network router to cover it all.
Let's talk about the issues that might appear with an Extender network.

1. Network Extenders that will help cover poor signal in your home, often results in poor connection and low speed performance.
2. Often the Network Extender is a low budget device or not suited for having too many devices attached to it.
3. Placement of the speaker is crucial as you can put it in a place where it could connect to either main Wireless router or the Extender, that will confuse Wireless network devices.
4. To solve this issue, try move the speaker closer to main router or have fewer devices attached to your Wireless Extender.
5. In addition, always use 5GHz connection between your Network extender and main router (best solution and performance).

One Wireless Network Name (SSID)

1. You may have set the Wireless Network SSID (Wi-Fi network name) to one big Wireless network (With a main router + Extender(s).
2. If the Wireless speaker is within range of both Wireless networks (Main router & Extender) then it can get confused with which one to connect to.
3. To solve this issue, using two different name for your extended network will help with the performance of the Wireless connected speaker and Google Assistant request.

 

The Checklist

Let us walk-through a list of things needed to ensure every requirement is met.

1. Check your mobile device if that is able to connect to same Wireless network.
2. Make sure you are within range of your Wireless router.
3. Check the Wireless signal on your mobile device, does it have a weak signal then move closer to the router.
4. Try both Wireless network bands 2.4GHz and 5GHz in case one of them are failing.
   1. You will have longer range with 2.4GHz, but less performance and most of the times a crowded network (many devices are using 2.4GHz band).
   2. You will have less interference with 5GHz and higher performance, however, the range of the 5GHz network has shorter range.
5. Try using a different mobile device, if you have one.
6. Reboot your Wireless network router and your mobile device.

Watch the video below for help with setting up your Google Assistant device.

Wireless Network Extender

Some houses or apartments can be too big for one Wireless network router to cover it all.
Let's talk about the issues that might appear with an Extender network.

1. Network Extenders that will help cover poor signal in your home, often results in poor connection and low speed performance.
2. Often the Network Extender is a low budget device or not suited for having too many devices attached to it.
3. Placement of the speaker is crucial as you can put it in a place where it could connect to either main Wireless router or the Extender, that will confuse Wireless network devices.
4. To solve this issue, try move the speaker closer to main router or have fewer devices attached to your Wireless Extender.
5. In addition, always use 5GHz connection between your Network extender and main router (best solution and performance).

One Wireless Network Name (SSID)

1. You may have set the Wireless Network SSID (Wi-Fi network name) to one big Wireless network (With a main router + Extender(s).
2. If the JBL LINK device is within range of both Wireless networks (Main router & Extender) then it can get confused with which one to connect to.
3. To solve this issue, using two different name for your extended network will help with the performance of the JBL LINK Speaker and Google Assistant request.

 

You can clean it by wiping it gently with a damp cloth. Take extra care not to let water leak into the speaker chamber, as it will damage the speaker drivers.

You can adjust Equalizer, Spatial Sound, RGB LED effects, change microphone settings and update the headset's firmware

You cannot download the JBL Portable App on a PC. This app is only available on mobile devices.

The JBL Free X does not feature volume control. In order to adjust the volume, you must manually increase/decrease from your device.

In the event that ear pieces do not re-pair automatically to paired Bluetooth device, power off ear pieces individually by press and hold the buttons for 5 seconds. To enter Bluetooth pairing mode when ear pieces are powered off, press and hold on buttons of both earpieces for 8 seconds. Re-pair the right ear piece with desired Bluetooth device when LED indicator on right ear piece alternates between blue and white LED lights.

In the event that left and right ear piece pairing is lost, power on both ear pieces and press the buttons 3 times on each ear piece to initiate re-pair.

The JBL Free automatically switches from stereo to mono when making or taking phone calls. Voice calls will only come through the right ear piece for a more natural call experience.

When you place the two Free earphones in the charging case, you will see a white led ring light up on both of them. At the same time, some of the four dot-leds on the charging case will light up to indicate the battery level of the case battery. When the earphones are fully charged, the white led ring goes out on each of them. When both are fully charged, the charging case charging level leds go out too.

Please use an OBD II extension cable in this case. An extension cable is not included in the package but they are readily available for purchase on-line.

Please check with your car manufacturer to ensure your car supports CAN or K-line. JBL DRG only works with CAN and K-line to get the engine data for engine sound simulation. If your car does support CAN or K-line, please launch the JBL DRG app and check the engine sound volume bar (the right column with button marked with “E”) in the “Sound Mode” section to make sure it is not turned off.

This headphone does not feature volume control. You must manually control volume from your device.

Yes, the Xtreme 2 features an IPX 7 rating. IPX7 is defined as the speaker can be immersed in water up to 1 meter for up to 30 minutes.

No. The 600BTNC headphone does not feature any IPX rating that protects it against sweat or water. Over exposure to water can compromise the controls on the headphones.

There is a Wi-Fi indicator on the back of the main speaker, and when it turns amber, it indicates that the Wi-Fi signal is weak. Try to move the speaker closer to your Wi-Fi router, and when the signal indicator turns White again, then it has a steady connection.

Yes, the cable has a one-button remote control and a microphone. This means that you can pause, resume play, you can pick up the phone and stop a call, and talk to other people through the microphone. There is no option to control music volume on the cable remote. That is only possible when using the Bluetooth system for wireless listening, with the volume buttons on the ear pod.

No, this cable is straight, with no remote control. The headphones have remote control buttons on the ear pods, which can be used when listening over Bluetooth wireless.

No, the app works with the ELITE models only. These are the ones that feature Active Noise Cancelling.

With the release of v.3.0 of the JBL Music app, owners of the JBL Authentics L8 and L16 are now greeted with a message that an update is available. If you own one of these speaker systems, and you know that it already supports Spotify Connect, the update firmware is already installed, and you can ignore this message. If your speaker system does not already support Spotify Connect, the update is available for you, but you cannot perform it yourself, it must go to a service center to be updated. Please contact Harman Helpdesk or the distributor in your country for advice regarding servicing.

No. The Live 200BT does not feature any IPX rating so overexposure to both sweat and water can compromise the headphones.

Yes, two flexible joints permit you to expand the collar to make it easier to place it around your neck.

It would depend where you buy it from. If you bought it in Germany, it will speak German from the start and if you bought it from USA or UK it will speak English. The langauge of the speaker can be changed in our HK Alexa setup app. Go to Settings, Device, Language and select your preferred language.

No, it is compatible with PC and Mac, but not with PS4, XBOX One, Nintendo Switch or Mobile.

The JBL Flip 7 has an IP68 water and dustproof rating, meaning it's protected from water and dirt.

The speaker can be submerged in up to 1.5 meters of water for up to 30 minutes.

No. The Dual Wireless Sound featured in the Onyx Studio 5 only gives you the capability to connect to a second Onyx Studio 5. It is not possible to connect the Onyx Studio 3 and 5 together. The Onyx Studio 5 can only be connected to no more than one other Onyx Studio 5.

Actually the N5005 is very special, because it is BOTH wireless and wired, right out of the box! This is a result of its advanced design, where the cables can be removed from the speaker pods by clicking apart the MMCX connectors. The flexibility in this arrangement becomes very clear when you look at the cables that are in the box when you open it. First, there is the normal cable with 3.5 mm stereo jack and a three-button remote control. This cable is for normal sources, smartphones, tablet computers etc. There is a switch on the back of the remote that permits you to select Android/universal or iOS remote function, for total flexibility. Second, you get the Bluetooth cable, which has a battery box and a three-button remote on the cable. This cable simply converts your N5005 into a wireless headphone. AptX and AAC are supported, but not aptX HD or LL. BT transmission will not be capable of unlocking the full potential of the N5005 due to its nature as a lossy compression system, but it is nice to have this option. The cable has a chin slide lock that can secure the headphones under your chin. Playing time is up to 8 hours, and charging takes place in less than 2 hours. Third, as an indication of the high quality of audio that N5005 masters, you get a special, fully balanced cable without remote control. It uses the 4-pole 2.5 mm jack that you will find on the new generation of high-end headphone amplifiers and music players. With this connection and the proper source material and electronics, you can experience the pinnacle of music reproduction.

This model is not supported by the JBL Partybox App.

The OMNI BAR+ as standalone system is 2.1, however when using it in a 5.1 wireless surround system, it generates a virtual acoustic center speaker to complete the 5.1 Surround system. In that combination it will be a 3.1 system.

Yes, two headsets can be used simultaneously with one transmitter.

No, this is not possible. Even though the MMCX (micro-miniature coaxial) connectors seem identical, they are not the same dimensions.

While this is indeed possible, no such cable is made by AKG, so only cables from third-party manufacturers may be considered. Please note that internal pin configuration must be identical to the original cable for such a cable to work with the headphones.

Yes, Alexa has various voice commands to turn up the volume. Try saying "Alexa, turn it up" or "Alexa, set volume to 5".

Yes, but only via cable, and noise cancelling cannot be activated meanwhile. Since the charging socket is located on top of the ear pod, adjustment is limited in that direction while the micro-USB plug is inserted.

The lights cannot be adjusted by user. The digital front panel display has automatic light intensity adjustment, which follows the level of light in the room.

Make sure your WiFi extender's name is not the same as that of your main WiFi network. Please use 5 GHz WiFi extenders only for best performance.

Please make sure that if you use 5GHz or 2.4GHz Wi-Fi, all your speakers are connected to either 2.4GHz or all are connected to 5GHz Wi-Fi to have the best performance.

Please make sure that the audio out format is set to PCM in the TV. Dolby Digital or other surround formats will not work with the BTA 20 transmitter.

• Please check whether you connected JBL DRG with your smartphone and head unit via Bluetooth before, then power off the head unit. • If you have, wait 2 minutes for JBL DRG to reconnect to smartphone after power on. This is because JBL DRG will automatically search for the head unit, first then the smart phone.

DVD and Blu-ray Disc copy protection only allows analog video output up to 576p resolution when playing DVDs and Blu-ray Discs. To view video at higher resolutions use the AVR’s HDMI inputs and HDMI output instead of its component video inputs and output.

Make sure that both speakers are using the same network technology, either Ethernet or WiFi. Mixing them will increase music loading time.

No, using two virtualization algorithms at the same will very negatively affect the performance and sound quality. Be sure you’re only using one surround sound solution at a time.

Usually, the first time you connect the N90Q to your computer with the USB cable, and turn the headphone ON, it will cause a message to open on your computer, informing you that this new device has been connected, and a software package is being imported.
Next time, you may get a warning that your USB device is not recognized by the computer, but that does not mean that the headphone will not work, it just means that you must activate it in the audio control systems.

1. 
   Locate the speaker symbol, which is usually shown at the extreme right in your computer taskbar along the bottom of the screen.
2. 
   Right-click on the speaker symbol.
3. 
   A menu opens, and you must highlight and click on Playback Devices.
4. 
   Now a small window opens, showing the Playback tab, with all available speaker option.
5. 
   One of the options should read something like this: " Speakers. AKG N90 headphones - Firmware version A2.12. Ready."
6. Highlight this option, and then click the "Set Default" button that is now available in the window. Audio should immediately be sent to the N90 headphones as a digital signal, which is then converted and amplified inside the headphones.
7. Now you can enjoy world-class music listening.

If the computer will not show N90Q as an option, it is usually a solution to disconnect the headphone, then reconnect it. Sometimes this must be done two or three times before the computer "sees" the headphone.
 

It is not possible to use the speaker while installing it to your WiFi network. Once you have successfully connected to the WiFi network, you can use Bluetooth and AUX again.

Unfortunately, some Huawei phones are not able to stream music from the HK Controller app to 1st generation Omni speakers. However, the new Omni 10+, 20+, and 50+ have fixed this issue, and you will be able to stream music to them using your Huawei phone.

Please note that two types of ear tips are included with AKG N5005. The black ones are normal silicone tips, and they are fine for many users. The Milky-white ones are from the company SpinFit. They have a special middle section that permits the tip to swivel in all directions, making them able to adapt to various insertion angles. Please try both. For some, one is better, for some, the other one is better. You make the decision. In normal use, the tip that makes the best seal with your ear canal is the best choice, since bass reproduction is very dependent on this seal. However, some users may find that they prefer a slightly less tight seal.

This feature is not yet implemented in our Harman Kardon Allure or Allure portable speaker. Future updates might include this option, so we advise keeping an eye on the release notes in the HK Alexa Setup app about possible future firmware updates.

If you are experience this message, please power cycle the Wi-Fi router and speaker(s). Disconnect the devices' power cable for 10 seconds and then reconnect them. Once the router and speaker(s) completely boots up, please try to setup again.

Some third-party apps do not support volume changing when your smart device is in lock screen mode.

It sounds like you are living in a country where Google Assistant has not yet been officially released. When Google releases the Google Assistant to more countries, the Everest GA headphones will open up for this feature. It may require a software update for this to happen. For now, you can use them as normal Bluetooth headphones and wait for the release to use the Google Assistant feature.

If you are having problems playing music after setting up a new speaker (no matter what connection is used, Ethernet, Wi-Fi), please restart the Harman Kardon Controller app after the speaker setup is complete.

Please keep the app running during a firmware upgrade. This is because the app is using BLE to transfer firmware to the JBL DRG. If you exit or kill the app, this will cause the BLE connection to be broken and the upgrade will not complete.

JBL DRG will auto reconnect to the last device. To setup a connection with new Bluetooth head unit, press the “reset” button in the App. The device will then search for a discoverable Bluetooth connection and setup.

Make sure you disable AP/Client isolation on your Access Point / Extender and that Multicast forwarding is not disabled between the W-Fi networks. However, we cannot guarantee than streaming will work flawless as Extender networks are tricky and can cause many issues. Always use a 5GHz Wi-Fi network extender for best results.

It is offering low-latency wireless connectivity via a 2.4Ghz signal that is enabled by a USB dongle included in the box. Turn on the slider, then it automatically connect to the dongle. If you loss the connectivity with the dongle, power on with the slider and hold on for 5 seconds and press and hold the dongle to make sure the pairing until listening to the tone.

Before you start

• Remove any interference that might be blocking the Soundbar side-firing speakers.
• Any ambient noise or sounds that could disrupt the calibration needs to be out of the room.
• In case you are moving the Enchant Soundbar you will need to calibrate the sound again.
• If something went wrong, you can always delete the calibration settings by resetting the system.
  • Press and hold button and  button down for 5 seconds.
  • This will delete all settings, including the Wi-Fi connection.

How to use the MultiBeam feature

1. Press and hold the CALIBRATION button for 3 seconds.
   1. On the Enchant display a timer will start counting down from 3 to 0 (Once hitting 0 the Calibration will begin).

2. The calibration takes around 60 seconds before it is complete. While calibrating you will hear some noises coming from the speaker.
3. When finished the display on the Enchant Soundbar will say "DONE"

 

This video shows how to use a smart speaker that has Google Assistant built-in.
Our LINK series have Google Assistant built-in therefore you can practice your voice commands together with Harman/Kardon Citation or JBL LINK products