Please note that two types of ear tips are included with AKG N5005. The black ones are normal silicone tips, and they are fine for many users. The Milky-white ones are from the company SpinFit. They have a special middle section that permits the tip to swivel in all directions, making them able to adapt to various insertion angles. Please try both. For some, one is better, for some, the other one is better. You make the decision. In normal use, the tip that makes the best seal with your ear canal is the best choice, since bass reproduction is very dependent on this seal. However, some users may find that they prefer a slightly less tight seal.

This feature is not yet implemented in our Harman Kardon Allure or Allure portable speaker. Future updates might include this option, so we advise keeping an eye on the release notes in the HK Alexa Setup app about possible future firmware updates.

If you are experience this message, please power cycle the Wi-Fi router and speaker(s). Disconnect the devices' power cable for 10 seconds and then reconnect them. Once the router and speaker(s) completely boots up, please try to setup again.

Some third-party apps do not support volume changing when your smart device is in lock screen mode.

It sounds like you are living in a country where Google Assistant has not yet been officially released. When Google releases the Google Assistant to more countries, the Everest GA headphones will open up for this feature. It may require a software update for this to happen. For now, you can use them as normal Bluetooth headphones and wait for the release to use the Google Assistant feature.

If you are having problems playing music after setting up a new speaker (no matter what connection is used, Ethernet, Wi-Fi), please restart the Harman Kardon Controller app after the speaker setup is complete.

Please keep the app running during a firmware upgrade. This is because the app is using BLE to transfer firmware to the JBL DRG. If you exit or kill the app, this will cause the BLE connection to be broken and the upgrade will not complete.

JBL DRG will auto reconnect to the last device. To setup a connection with new Bluetooth head unit, press the “reset” button in the App. The device will then search for a discoverable Bluetooth connection and setup.

Make sure you disable AP/Client isolation on your Access Point / Extender and that Multicast forwarding is not disabled between the W-Fi networks. However, we cannot guarantee than streaming will work flawless as Extender networks are tricky and can cause many issues. Always use a 5GHz Wi-Fi network extender for best results.

It is offering low-latency wireless connectivity via a 2.4Ghz signal that is enabled by a USB dongle included in the box. Turn on the slider, then it automatically connect to the dongle. If you loss the connectivity with the dongle, power on with the slider and hold on for 5 seconds and press and hold the dongle to make sure the pairing until listening to the tone.

Before you start

• Remove any interference that might be blocking the Soundbar side-firing speakers.
• Any ambient noise or sounds that could disrupt the calibration needs to be out of the room.
• In case you are moving the Enchant Soundbar you will need to calibrate the sound again.
• If something went wrong, you can always delete the calibration settings by resetting the system.
  • Press and hold button and  button down for 5 seconds.
  • This will delete all settings, including the Wi-Fi connection.

How to use the MultiBeam feature

1. Press and hold the CALIBRATION button for 3 seconds.
   1. On the Enchant display a timer will start counting down from 3 to 0 (Once hitting 0 the Calibration will begin).

2. The calibration takes around 60 seconds before it is complete. While calibrating you will hear some noises coming from the speaker.
3. When finished the display on the Enchant Soundbar will say "DONE"

 

This video shows how to use a smart speaker that has Google Assistant built-in.
Our LINK series have Google Assistant built-in therefore you can practice your voice commands together with Harman/Kardon Citation or JBL LINK products

Onboard Active Noise Cancelling is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SINGLE press the ANC button to toggle it On/Off  and LONG press to active TalkThru. Turn on ANC again by a single press on the multi-function button.

To show the current firmware version on your JBL TUNER device, go through the following steps.

1. Turn on the JBL TUNER.
2. Press and hold this three-button combination: DAB/FM+ Volume+ and Preset 5, simultaneously for 3-4 seconds.
3. In the display, you will see a combination of letters and numbers. This is the current software version.
4. See picture below as illustration.

The new firmware version released is V.0.0.57 (shown in the picture above).
To get the latest version, ask our customer service for a guide and an upgrade file.

 

Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.



How to check your PC settings for the correct recording device
1. Go to Control Panel

2. Select Hardware and Sound

3. Click on Sound

3 Select  Recording


4. Make sure to select the proper recording device.

1. Right-click on it Quantum headset.

   

2. Now select "Set Default Device" or Select "Default Communication Device"

   

5. Check the microphone levels by right-click on your Quantum headset. Then click on Properties


6. Choose Levels.


7. Adjust accordingly.
 

Please also make sure the volume control on the headset is turned up. Rotate the volume wheel on your headset to increase the volume.
Check that your headset's Game-Chat balance dial and ensure that the balance is correct, you might refer to the screenshot below from the QuantumEngine PC software.


If you still cannot hear the game or music audio, or if the volume is still very low, check if the TalkThrough is activated via the QuantumEngine software.


Finally, you can also do a short press on the Smart Ambient button on the headset (if your headset, has this feature)

Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.

Check that the PC is using the correct recording device.

1. Go to Control Panel

2. Select  Sound 

3 Select  Recording

4. Make sure to select the proper recording device.

1. Right-click on it Quantum headset.
2. Now select "Set Default Device" or "Select Default Communication Device"

5. Check the microphone levels by right-click on your Quantum headset.

6. Go to Properties

7. Chose Levels and adjust accordingly

Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.

Check that the PC is using the correct recording device.

1. Go to Control Panel

2. Select  Sound 

3 Select  Recording

4. Make sure to select the proper recording device.

1. Right-click on it Quantum headset.
2. Now select "Set Default Device" or "Select Default Communication Device"

5. Check the microphone levels by right-click on your Quantum headset.

6. Go to Properties

7. Choose Levels and adjust accordingly

1. Power on your JBL LINK speaker.
2. Verify that you are connected to the right Wi-Fi network on your smartphone.
3. Open your Google Home app .
4. Enable Bluetooth
5. Enable Location Service (Android Only)
   1. Make sure you have permitted the Google Home app to view your location.
6. First option Tap Add Set up device Set up new devices in your home
7. Second  option Tap X device found Select Home location
8. Follow the instruction on screen to add your new JBL LINK speaker.

You are now all set and can enjoy your LINK device!

Download the Google Home app, available for iOS and Android versions. 1. Open the Google Home app. 2. Plug in power for your Enchant 800 or Enchant 1300 Soundbar. 3. Enable Bluetooth. 3.1. Enable Location service on your phone and permit Google Home app to view your location (Android only). 4. Click setup device in your Google Home app. 5. Follow the instructions provided in the app, and enjoy Chromecast streaming for your Enchant soundbar!

What you need first

• A Harman/Kardon Enchant Soundbar (1300 or 800 model).

• Latest version of the Google Home app
• A mobile device or tablet with Android or iOS system.
• An internet connection.
• Dual-band router with 2.4GHz and 5GHz connection

Adding your Enchant soundbar to your Wi-Fi

1. Open the Google Home app

      

2. Click on "ADD" to connect your Enchant 800 or Enchant 1300 Soundbar to your Wi-Fi network.
3. Follow the instructions on screen and enjoy beautiful sound using Chromecast technology.

1. Power on the Enchant 800 or Enchant 1300 Soundbar. 2. In any source mode, press the power and source button for 5 seconds. 3. The Enchant 800 or Enchant 1300 will power off automatically and turn on again. 4. Your device is now reset back to default Factory settings. 5. You can now redo the setup through the Google Home app or pair with a new smartphone or tablet.

Resetting the device

1. In any source mode, press and hold the power button and Source button for 5 seconds.
2. When the factory settings restore is complete, the soundbar automatically turns off and restarts.
3. You can now set it up via Google Home app again or connect any new Bluetooth devices.

On the bottom of your ADAPT+ there is a reset button. Hold it down for 5 seconds, until the round button LED lights up in white. The product is now reset and ready to be set up again.

In order to reset the headphones: 

Long Press of volume + and volume - at the same time while the unit is on. Make sure that bluetooth is NOT on and connected to any device. 
When reseting, LED will blink faster. 

Resetting the Partybox to Factory Settings

1. Press and hold "Play/Pause" and "Volume +" down for > 10 seconds.
2. The JBL Partybox will power off and back on and is now reset.

Press and hold the 'DAB/FM' & 'Preset 1' buttons for more than 2 seconds. The Horizon 2 is now reset to the default factory settings.

Resetting the SOUNDSTICKS 4 to Factory Settings

1. The unit must be on
2. Press and hold Power and Bluetooth buttons for > 10 seconds
3. The unit is reset

Power on the JBL Pulse 3 For 5 seconds, press and hold the "Volume +" and "Play" buttons The JBL Pulse 3 will power off, and is now reset

In power ON mode press and hold the "Volume +" and "Play" buttons at the same time for more than 3 seconds -> Unit will power Off by itself. Now the unit is reset to factory default.

Press and hold the 'Volume +' and 'Bluetooth' buttons simultaneously for > 2 seconds (> 5 seconds for the Onyx Studio 8), until the speaker powers off.
The Onyx Studio is now reset to factory settings.