Onboard Active Noise Cancelling is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SINGLE press the ANC button to toggle it On/Off  and LONG press to active TalkThru. Turn on ANC again by a single press on the multi-function button.

To show the current firmware version on your JBL TUNER device, go through the following steps.

1. Turn on the JBL TUNER.
2. Press and hold this three-button combination: DAB/FM+ Volume+ and Preset 5, simultaneously for 3-4 seconds.
3. In the display, you will see a combination of letters and numbers. This is the current software version.
4. See picture below as illustration.

The new firmware version released is V.0.0.57 (shown in the picture above).
To get the latest version, ask our customer service for a guide and an upgrade file.

 

Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.



How to check your PC settings for the correct recording device
1. Go to Control Panel

2. Select Hardware and Sound

3. Click on Sound

3 Select  Recording


4. Make sure to select the proper recording device.

1. Right-click on it Quantum headset.

   

2. Now select "Set Default Device" or Select "Default Communication Device"

   

5. Check the microphone levels by right-click on your Quantum headset. Then click on Properties


6. Choose Levels.


7. Adjust accordingly.
 

Please also make sure the volume control on the headset is turned up. Rotate the volume wheel on your headset to increase the volume.
Check that your headset's Game-Chat balance dial and ensure that the balance is correct, you might refer to the screenshot below from the QuantumEngine PC software.


If you still cannot hear the game or music audio, or if the volume is still very low, check if the TalkThrough is activated via the QuantumEngine software.


Finally, you can also do a short press on the Smart Ambient button on the headset (if your headset, has this feature)

Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.

Check that the PC is using the correct recording device.

1. Go to Control Panel

2. Select  Sound 

3 Select  Recording

4. Make sure to select the proper recording device.

1. Right-click on it Quantum headset.
2. Now select "Set Default Device" or "Select Default Communication Device"

5. Check the microphone levels by right-click on your Quantum headset.

6. Go to Properties

7. Chose Levels and adjust accordingly

Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.

Check that the PC is using the correct recording device.

1. Go to Control Panel

2. Select  Sound 

3 Select  Recording

4. Make sure to select the proper recording device.

1. Right-click on it Quantum headset.
2. Now select "Set Default Device" or "Select Default Communication Device"

5. Check the microphone levels by right-click on your Quantum headset.

6. Go to Properties

7. Choose Levels and adjust accordingly

1. Power on your JBL LINK speaker.
2. Verify that you are connected to the right Wi-Fi network on your smartphone.
3. Open your Google Home app .
4. Enable Bluetooth
5. Enable Location Service (Android Only)
   1. Make sure you have permitted the Google Home app to view your location.
6. First option Tap Add Set up device Set up new devices in your home
7. Second  option Tap X device found Select Home location
8. Follow the instruction on screen to add your new JBL LINK speaker.

You are now all set and can enjoy your LINK device!

Download the Google Home app, available for iOS and Android versions. 1. Open the Google Home app. 2. Plug in power for your Enchant 800 or Enchant 1300 Soundbar. 3. Enable Bluetooth. 3.1. Enable Location service on your phone and permit Google Home app to view your location (Android only). 4. Click setup device in your Google Home app. 5. Follow the instructions provided in the app, and enjoy Chromecast streaming for your Enchant soundbar!

What you need first

• A Harman/Kardon Enchant Soundbar (1300 or 800 model).

• Latest version of the Google Home app
• A mobile device or tablet with Android or iOS system.
• An internet connection.
• Dual-band router with 2.4GHz and 5GHz connection

Adding your Enchant soundbar to your Wi-Fi

1. Open the Google Home app

      

2. Click on "ADD" to connect your Enchant 800 or Enchant 1300 Soundbar to your Wi-Fi network.
3. Follow the instructions on screen and enjoy beautiful sound using Chromecast technology.

1. Power on the Enchant 800 or Enchant 1300 Soundbar. 2. In any source mode, press the power and source button for 5 seconds. 3. The Enchant 800 or Enchant 1300 will power off automatically and turn on again. 4. Your device is now reset back to default Factory settings. 5. You can now redo the setup through the Google Home app or pair with a new smartphone or tablet.

Resetting the device

1. In any source mode, press and hold the power button and Source button for 5 seconds.
2. When the factory settings restore is complete, the soundbar automatically turns off and restarts.
3. You can now set it up via Google Home app again or connect any new Bluetooth devices.

On the bottom of your ADAPT+ there is a reset button. Hold it down for 5 seconds, until the round button LED lights up in white. The product is now reset and ready to be set up again.

In order to reset the headphones: 

Long Press of volume + and volume - at the same time while the unit is on. Make sure that bluetooth is NOT on and connected to any device. 
When reseting, LED will blink faster. 

Resetting the Partybox to Factory Settings

1. Press and hold "Play/Pause" and "Volume +" down for > 10 seconds.
2. The JBL Partybox will power off and back on and is now reset.

Press and hold the 'DAB/FM' & 'Preset 1' buttons for more than 2 seconds. The Horizon 2 is now reset to the default factory settings.

Resetting the SOUNDSTICKS 4 to Factory Settings

1. The unit must be on
2. Press and hold Power and Bluetooth buttons for > 10 seconds
3. The unit is reset

Power on the JBL Pulse 3 For 5 seconds, press and hold the "Volume +" and "Play" buttons The JBL Pulse 3 will power off, and is now reset

In power ON mode press and hold the "Volume +" and "Play" buttons at the same time for more than 3 seconds -> Unit will power Off by itself. Now the unit is reset to factory default.

Press and hold the 'Volume +' and 'Bluetooth' buttons simultaneously for > 2 seconds (> 5 seconds for the Onyx Studio 8), until the speaker powers off.
The Onyx Studio is now reset to factory settings.

Restore to factory settings:
In power ON mode, press and hold the Power Button for at least 10 seconds, until the volume and input selector lights begin to flash.
Reset to factory default includes Source, Volume settings, EQ settings, AirPlay name and Wi-Fi settings.

Daily Care instructions for Citation speakers fabric (wool) Daily care and immediate stain removal will ensure that your Harman/Kardon Citation wool upholstery will keep looking good for many years. Never use undiluted cleaning agents, bleaching agents, ammonia or soap intended for hard surfaces, as this may damage the fabric and Citation speaker itself! Many types of stain can be removed using warm water with a microfiber cloth (not too wet). Stain removal guide If you act quickly with any stains on your Citation device then it is not difficult to remove or avoid any spill/stains. Here is how to do it. First, soak up the liquid with an absorbent napkin or Microfiber cloth. For dried stains use a spoon to roughen the surface. To avoid the stain spreading further start from the edge of the stain working towards the middle. WARNING! Be careful when using solvents, because these could dissolve the upholstery material beneath. Regular and normal cleaning Vacuum frequently every week is the best way to keep the Harman/Kardon Citation fabric intact or use a varm wet Microfiber cloth. When using a vacuum cleaner, remember to set the power to half which is most appropriated to use for Citation devices (this will not harm the design or fabric). General information These tips are purely recommendations and cannot guarantee 100% stain removal on your Harman/Kardon Citation device. In all cases, we recommend contacting a professional cleaning company, particularly for bigger stains and for thorough cleaning the wool fabric and speaker. HARMAN do not have any recommended companies or partners to redirect any customers too. For furter information we advise visiting the fabric company called KVADRAT by clicking on these links below: https://kvadrat.dk/care-and-maintenance/upholsteries https://kvadrat.dk/download/media/download-section/relatedfiles/kvadrat-maintenance-manual-2016-uk.pdf There are a lot of information about the fabric we are using and you can contact them for further information.

Daily Care instructions for Citation speakers fabric (wool)

Daily care and immediate stain removal will ensure that your Harman/Kardon Citation wool upholstery will keep looking good for many years.
Never use undiluted cleaning agents, bleaching agents, ammonia or soap intended for hard surfaces, as this may damage the fabric and Citation speaker itself!

Many types of stain can be removed using warm water with a microfiber cloth (not too wet).

Stain removal guide

If you act quickly with any stains on your Citation device then it is not difficult to remove or avoid any spill/stains.
Here is how to do it.

1. First, soak up the liquid with an absorbent napkin or Microfiber cloth.
2. For dried stains use a spoon to roughen the surface.
   1. To avoid the stain spreading further start from the edge of the stain working towards the middle.
3. WARNING!
   1. Be careful when using solvents, because these could dissolve the upholstery material beneath.

Regular and normal cleaning

Vacuum frequently every week is the best way to keep the Harman/Kardon Citation fabric intact or use a varm wet Microfiber cloth.
When using a vacuum cleaner, remember to set the power to half which is most appropriated to use for Citation devices (this will not harm the design or fabric).
 

General information

These tips are purely recommendations and cannot guarantee 100% stain removal on your Harman/Kardon Citation device.
In all cases, we recommend contacting a professional cleaning company, particularly for bigger stains and for thorough cleaning the wool fabric and speaker.
HARMAN do not have any recommended companies or partners to redirect any customers too.

For furter information we advise visiting the fabric company called KVADRAT by clicking on these links below:
https://kvadrat.dk/care-and-maintenance/upholsteries
https://kvadrat.dk/download/media/download-section/relatedfiles/kvadrat-maintenance-manual-2016-uk.pdf

There are a lot of information about the fabric we are using and you can contact them for further information.

USB Stick

1. Get an empty stick with speed of 2.0.
2. Make sure it is formatted with FAT16 or FAT32.
3. Your Music files can only be:  (32-320kbit/s), (32-320kbit/s) and (44.1K/48K/192K).
4. The Partybox supports up to 8 subfolders.
5. It will be played in alphabetic sequence with main folders first then subfolders.
6. To skip songs forward, double press the Play/Pause button. To skip back, triple press the Play/Pause button.

This video shows how to play music and much more with your Google Assistant. You can practice all of your voice commands on your Harman/Kardon Citation or JBL LINK products.

To perform a hardware reset of your earbuds, press and hold the reset button on the charging case* for more than 5 seconds. This resets the earbuds without restoring the settings to the factory defaults.
* Location
Live 300TWS/Live Pro+ TWS: Inside the charging case between the earbuds.
Live Free NC+/Reflect Mini NC TWS/Reflect Aero: On the back of the charging case, next to the USB-C port.
Club Pro+ TWS: On the bottom of the charging case, next to the USB-C port.