How To
How To
435 results
-
Connecting a Bluetooth device for your Enchant Soundbar
- Make sure your Enchant soundbar is turned on by pressing the power button
- There are two ways to enter Bluetooth pairing mode on your Enchant soundbar.
- Press the dedicated source button on top of your Enchant soundbar
- Press the source button until you see "Bluetooth" in the front of the Enchant display. Below is the order when using the source button (note that on Enchant 800 there is only 1 HDMI)
- Press the dedicated source button on top of your Enchant soundbar
- The second option is to use the Remote control included with your Enchant soundbar.
- Press the "BT" button on your Remote control.
- The display will show "Bluetooth pairing"
- Now that your Enchant soundbar is in pairing mode it is now time to grab your mobile device.
- Go to Bluetooth settings.
- Press the enable Bluetooth button.
- Select the Enchant soundbar and connect with Bluetooth.
You can now stream any music from your favorite device directly to the Enchant soundbar, ENJOY!
Was this helpful? Thank you for your feedback! - Make sure your Enchant soundbar is turned on by pressing the power button
-
With a short press of the dedicated Bluetooth button on the underside of the right ear cup, it powered on and enter the pairing mode.
Was this helpful? Thank you for your feedback! -
You can clean it by wiping it gently with a damp cloth. Take extra care not to let water get into the speaker chamber, as it will damage the speaker drivers.
Was this helpful? Thank you for your feedback! -
The battery is charged using an included USB-A to USB-C USB fabric cable. It will be fully charged for 2 hrs. Note, this cable is only for charging the battery, it will not deliver audio.Was this helpful? Thank you for your feedback!
-
You might have to add a USB extension dock to get the JBL Quantum 350/600/800/810 dongle as close to the headset, or place the common sources of interference (e.g. routers, Wi-Fi speakers etc.) as far from the JBL Quantum 350/600/800/810 dongle.
Was this helpful? Thank you for your feedback! -
You can connect 3 smart devices ( iOS or Android ) simultaneously by Bluetooth. One when connecting via AUX cable.Was this helpful? Thank you for your feedback!
-
Up to four headsets can play simultaneously. For each additional headset, hold the pairing buttons on both transmitter and headset for 5 seconds, then release. Now switch the transmitter off and on again with the pairing button, and the connection is active.Was this helpful? Thank you for your feedback!
-
They support up to 8 paired devices without reset.Was this helpful? Thank you for your feedback!
-
If your OMNI 50+ is completely drained, it will take 3,5 to 4 hours to fully charge. We advise to charge the Omni 50+ when it starts to blink red.Was this helpful? Thank you for your feedback!
-
You can listen up to 8 hours of MP3 music, with a fully charged battery, depending on volume and type of musicWas this helpful? Thank you for your feedback!
-
By pressing and holding the Bluetooth and the Volume PLUS buttons at the same time. The software version is shown in the display.Was this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up for 2-3 seconds and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. Once connected, you will see a solid blue light above the power button.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Message Us
Chat with a support agent via Whatsapp at:
91 70658 44446
Mon - Sun: 10:00 am - 7:00 pm (IST)