After installing the JBL QuantumENGINE, and audio outputs are correctly set up, there is no output from; Center and Surround channels. You can run the Channel ID (7.1) test to confirm.
 In JBL QuantumENGINE, go to the Spatial Sound tab, press the “Channel Setup” just below the “Channel ID” test.
2. Right click the Quantum Game-speaker output and select “Properties”.
3. Make sure that box is checked at “Enable Audio Enhancements”

 

Yes. InfinityLab charger is designed with surge protection to keep your devices safe.

The JBL Quantum 300 headset is compatible with PC, PlayStation, Xbox, Nintendo Switch, Mobile, Mac and VR.
You can also use the included USB dongle on PC, PlayStation and Mac.

The JBL Quantum 400 headset is compatible via 3.5mm jack with PC, PlayStation, Xbox, Nintendo Switch, Mobile, Mac and VR.
You can use the USB connection with PC, PS4, Nintendo Switch, and Mac.

SA750 Software Revival Guide

Reason	Revival method for SA750 if a problem exists after a stalled software update
Symptoms	Unit will display “NET UPDATING” on the front panel display and will not complete startup
Parts required	1) a USB stick, 2) a computer for transferring files to the USB stick, 3) unit software detailed in this guide

                             

1. Download the software bundle by clicking here . You will download a zipped folder called “SA750 v1542 Reflash Bundle.zip”
2. Unzip/extract this folder (some computers will do this automatically). Inside the folder you will find 2 more folders named “Step 1 V1206 V1.72” and “Step 2 V1542 V1.72”
3. Double click on the “Step 1 V1206 V1.72” folder. Inside you will find a file named “image.swu”
4. Copy this image.swu file to a blank USB memory stick.
   • NOTE! The file MUST be called image.swu. If you copy the file to a location where there is already a file called image.swu your computer may rename the file automatically (for instance as “image.swu (1)”. Please double check that the file is called “image.swu” when on the memory stick.
5. Power off the SA750 from the hard power switch on the rear of the unit immediately above the mains inlet socket.
6. Insert the USB memory stick into the rear of the unit.
7. Depress the recessed service switch (above the CD input connector sockets) and continue to keep it depressed.
8. Power the unit on whilst keeping the service button depressed.
9. Keep the service button depressed for at least 30 seconds after power on.
10. Release the service button.
11. Leave the unit for at least 30 minutes to update.
12. Perform a NET reset (MENU > SYSTEM SETTINGS > NET RESET).
13. Perform a SYSTEM reset (MENU > SYSTEM SETTINGS > SYSTEM RESET).
14. Functionality should now be revived. To update to the most current software version repeat points 3-13 above but using “Step 2 V1542 V1.72” at point 3.     

 

SA30 Software Revival Guide

Reason	Revival method for SA30 if a problem exists after a stalled software update
Symptoms	Unit will display “NET UPDATING” on the front panel display and will not complete startup
Parts required	1) a USB stick, 2) a computer for transferring files to the USB stick, 3) unit software detailed in this guide

                               

1. Download the software bundle by clicking here . You will download a zipped folder called “SA30 v1542 Reflash Bundle.zip”
2. Unzip/extract this folder (some computers will do this automatically). Inside the folder you will find 2 more folders named “Step 1 V1206 V1.72” and “Step 2 V1542 V1.72”
3. Double click on the “Step 1 V1206 V1.72” folder. Inside you will find a file named “image.swu”
4. Copy this image.swu file to a blank USB memory stick.
   • NOTE! The file MUST be called image.swu. If you copy the file to a location where there is already a file called image.swu your computer may rename the file automatically (for instance as “image.swu (1)”. Please double check that the file is called “image.swu” when on the memory stick.
5. Power off the SA30 from the circular front panel power button on the right hand side.
6. Insert the USB memory stick into the rear of the unit.
7. Depress the service switch and continue to keep it depressed.
8. Power the unit on whilst keeping the service button depressed.
9. Keep the service button depressed for at least 30 seconds after power on.
10. Release the service button.
11. Leave the unit for at least 30 minutes to update.
12. Perform a NET reset (MENU > SYSTEM SETTINGS > NET RESET).
13. Perform a SYSTEM reset (MENU > SYSTEM SETTINGS > SYSTEM RESET).
14. Functionality should now be revived. To update to the most current software version repeat points 3-13 above but using “Step 2 V1542 V1.72” at point 3.

 

Solo Uno Software Revival Guide

Reason	Revival method for Solo Uno if a problem exists after a stalled software update
Symptoms	Unit will likely have a solid blue network light and flashing orange status light and will not be available for streaming
Parts required	1) a USB stick, 2) a computer for transferring files to the USB stick, 3) unit software detailed in this guide

                               

1. Download the software bundle by clicking here . You will download a zipped folder called “Solo Uno v1542 Reflash Bundle.zip”
2. Unzip/extract this folder (some computers will do this automatically). Inside the folder you will find 2 more folders named “Step 1 V1206 V1.10” and “Step 2 V1542 V1.72”
3. Double click on the “Step 1 V1206 V1.10” folder. Inside you will find a file named “image.swu”
4. Copy this image.swu file to a blank USB memory stick.
   • NOTE! The file MUST be called image.swu. If you copy the file to a location where there is already a file called image.swu your computer may rename the file automatically (for instance as “image.swu (1)”. Please double check that the file is called “image.swu” when on the memory stick.
5. Power off the Solo Uno from the circular front panel power button.
6. Insert the USB memory stick into the rear of the unit.
7. Depress the service switch and continue to keep it depressed.
8. Power the unit on whilst keeping the service button depressed.
9. Keep the service button depressed for at least 30 seconds after power on.
10. Release the service button.
11. Leave the unit for at least 30 minutes to update.
12. Functionality should now be revived. To update to the most current software version repeat points 3-11 above but using “Step 2 V1542 V1.10” at point 3.

 

ST60 Software Revival Guide

Reason	Revival method for ST60 if a problem exists after a stalled software update
Symptoms	Unit will display “NET UPDATING” on the front panel display and will not complete startup
Parts required	1) a USB stick, 2) a computer for transferring files to the USB stick, 3) unit software detailed in this guide

                             

1. Download the software bundle by clicking here . You will download a zipped folder called “ST60 v1542 Reflash Bundle.zip”
2. Unzip/extract this folder (some computers will do this automatically). Inside the folder you will find 2 more folders named “Step 1 V1201 V0.72” and “Step 2 V1542 V0.72”
3. Double click on the “Step 1 V1206 V0.72” folder. Inside you will find a file named “image.swu”
4. Copy this image.swu file to a blank USB memory stick.
   • NOTE! The file MUST be called image.swu. If you copy the file to a location where there is already a file called image.swu your computer may rename the file automatically (for instance as “image.swu (1)”. Please double check that the file is called “image.swu” when on the memory stick.
5. Power off the ST60 from the circular front panel power button on the right hand side.
6. Insert the USB memory stick into the rear of the unit.
7. Depress the service switch and continue to keep it depressed.
8. Power the unit on whilst keeping the service button depressed.
9. Keep the service button depressed for at least 30 seconds after power on.
10. Release the service button.
11. Leave the unit for at least 30 minutes to update.
12. Perform a NET reset (MENU > SYSTEM SETTINGS > NET RESET).
13. Perform a SYSTEM reset (MENU > SYSTEM SETTINGS > SYSTEM RESET).
14. Functionality should now be revived. To update to the most current software version repeat points 3-13 above but using “Step 2 V1542 V0.72” at point 3.                    

Our LINK BAR supports 4K material and contents these different ways.

1. HDMI INPUT Supports 4K
2. Chromecast streaming in 4K.
3. 4K Material through the Android TV System.

You can watch your favorite 4K material in many different ways and enjoy!

If the earbuds go into standby mode and turn off, you can still use them without putting them back into the charging case. 
You can reactivate the headphones by pressing or touching the outside earbud itself.
Please note: They will be automatically powered off after 30 minutes of being in standby mode if they disconnect from Bluetooth. To reconnect, you will need to put the earbuds back in the charging case and take them off again. 

It is possible to change the standby mode time with your headphones. To do this, go into the My JBL Headphones app and choose the Standby Time via Auto-off function. You can adjust the time to 15min, 1hr, etc., or you can choose “Never” if you want to keep the earbuds turn on at all times. Once you set the Auto-off, the earbuds will work according to the setting whether they connect to Bluetooth or disconnect.
 

For the Club 950NC and 700BT, a dedicated button on the right ear-cup (*) for Bass Boost – gives the user the option to give an extra boost to their listening experience. Power surges from equipment (such as a panel/mixer) which would blow out a standard headphone could be experienced while playing at high power. Specially designed driver coil and magnet give a higher resistance to power surges. The maximum input power for CLUB 700BT is 1000 mW, for CLUB 950NC is 2000 mW and CLUB ONE is 3500 mW accordingly.

 

Switch the Soundgear ON. (If this is not possible, reset cannot be performed.)
Press and hold Volume + and Volume - simultaneously for longer than five seconds.
Soundgear switches OFF, and is now reset to factory settings.

If you experience any sound distortion after immersing your speaker in water, simply shake the speaker to get rid of any excess moisture and allow the speaker to completely dry. Once dry, the sound quality should return to normal.

Try another HDMI cable, and make sure that it is a high-speed version. This solution usually solves the problem, which is caused by insufficient cable bandwith.

"In certain network conditions, your speaker may not be visible from your streaming app. You can still use voice control to start & control playback. If you wish to use your phone app to control playback, please power cycle your Citation speaker and your phone."

Never remove a USB stick while the BDS is playing files from it. If the system freezes, switch the BDS unit OFF and then ON with the switch on the back panel to reset.

Please check that you have connected your android phone with JBL DRG before. Power off your Android phone and press the JBL DRG BT button to connect to another smartphone. If this is the case, please wait 3 minutes for JBL DRG to setup the Bluetooth connection with a new smartphone. This is because some android phones can’t send a “Disconnect” BT command to JBL DRG during power off, so JBL DRG need to wait until the Link is lost.

By optimizing Bluetooth settings via the app, you can get optimized audio in different scenarios like either listening to music or watching videos.
Select between “Normal” to optimize and stabilize the connection even in the busiest areas, “Music mode” to enjoy the best sound quality for music, and “Video mode” to get the best lip-syncing when watching or gaming.

 

The Horizon 2 does not have sleep mode functionality.

You can have your own Karaoke party with your JBL Partybox. Simply connect your Microphone (only included with the Partybox On The Go) and connect your mobile device over Bluetooth, then start playing music and sing along, it is that simple!

The JBL TOUR range helps you create an ideal world where you can entirely focus on your tasks.
With the JBL Tour One and Tour Pro+ TWS, you can get silent moments with SilentNow. Noise Cancelling is activated without Bluetooth, just by pressing a dedicated button on the headphones (or tapping the earbud) or controlling via the My JBL Headphones app. It also helps you save battery time.
Or get help in waking up with My Alarm, which allows sleep and wake times to be set and is controlled ​via the My JBL Headphones app. You can set a sleep and wake timer to gradually lower the volume of the headphones for sleep, switch into SilentNow mode for a specific amount of time and then wake you up at a specified time.

 

An optical connection will assure better audio performance and will support Dolby Digital audio from an HDTV.

An optical connection will assure better audio performance and will accept Dolby Digital audio from an HDTV. However, there are times when TV apps may not transmit audio through the digital optical output on the TV. In cases such as these, it would be necessary to use the analog AUX connection.

1. Power on your Harman Kardon Citation speaker.
2. Verify that you are connected to the right Wi-Fi network on your smartphone.
3. Open your Google Home app .
4. Enable Bluetooth
5. First option Tap Add Set up device Set up new devices in your home
6. Second  option Tap X device found Select Home location
7. Follow the instruction on screen to add your new Harman Kardon Citation speaker.

Still not sure how to connect, then watch this video below: