How To
How To
1413 results
-
It is not possible to use the speaker while installing it to your WiFi network. Once you have successfully connected to the WiFi network, you can use Bluetooth and AUX again.Was this helpful? Thank you for your feedback!
-
It is not possible to setup a speaker to a hidden SSID Wi-Fi network. Please make it visible to install your OMNI+ speakers.Was this helpful? Thank you for your feedback!
-
Make sure your source device and AURA are on the same network. Then make sure your router is set to support older Wi-Fi protocols, such as b/g where the AURA is operating. Some routers have a function to disable older protocols and only use newer ones.Was this helpful? Thank you for your feedback!
-
Unfortunately, some Huawei phones are not able to stream music from the HK Controller app to 1st generation Omni speakers. However, the new Omni 10+, 20+, and 50+ have fixed this issue, and you will be able to stream music to them using your Huawei phone.Was this helpful? Thank you for your feedback!
-
The most important thing, is to be sure that both blue LEDs must flash quickly, one on the center speaker, one on the subwoofer. If just one of these LEDs does not flash quickly, pairing cannot take place. If it is difficult to make one of the LEDs change to quick flash, it may be that the button is held too long, or not pressed in the right angle. Try again with a short, firm press less then a second.Was this helpful? Thank you for your feedback!
-
It is important to use the correct HDMI connection on the BDS, marked with ARC. Also, the proper input must be selected with the AUX input selector button, which scrolls between the six AUX inputs. It always selects the AUX input that you used last, so once you have used the AUX ARC input, the BDS unit remembers it until you select another AUX input. Of course you have to have a TV which actually supports ARC.Was this helpful? Thank you for your feedback!
-
Look at the back of the primary speaker, which is the one with pause/play and volume controls. You will see a switch called "mode". This switch can be in either S or P position. S stands for Secondary, P stands for Primary. Switch to Primary, and your speaker will now open Bluetooth and will accept analog signals. (The Secondary position is used for systems where four speakers are in use, since only one speaker can act as primary speaker.)Was this helpful? Thank you for your feedback!
-
Please note that two types of ear tips are included with AKG N5005. The black ones are normal silicone tips, and they are fine for many users. The Milky-white ones are from the company SpinFit. They have a special middle section that permits the tip to swivel in all directions, making them able to adapt to various insertion angles. Please try both. For some, one is better, for some, the other one is better. You make the decision. In normal use, the tip that makes the best seal with your ear canal is the best choice, since bass reproduction is very dependent on this seal. However, some users may find that they prefer a slightly less tight seal.Was this helpful? Thank you for your feedback!
-
The Harman Kardon Aura Studio 2 only supports Bluetooth. The HK Controller app only works with Harman Kardon products that have WiFi connectivity.Was this helpful? Thank you for your feedback!
-
There may be more than one reasons for this problem, but one detail is important: if establishing the connection manually, do not advance the cursor after having written all characters in your password with the up and down arrows. If you jump to the next empty position after the last character, this will be interpreted as an added character in itself, and the password will be wrong.Was this helpful? Thank you for your feedback!
-
This feature is not yet implemented in our Harman Kardon Allure or Allure portable speaker. Future updates might include this option, so we advise keeping an eye on the release notes in the HK Alexa Setup app about possible future firmware updates.Was this helpful? Thank you for your feedback!
-
Try reset the ESQUIRE2 speaker. Press and hold Volume + & phone button at the same time. When the unit is reset, it will power off, and turn on the unit again, and it is reset. Go into your Bluetooth device list and delete the ESQUIRE2 from your list. Now Bluetooth pair with it again. If the unit still do not work as intended, please contact our helpdesk.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Message Us
Chat with a support agent via Whatsapp at:
91 70658 44446
Mon - Sun: 10:00 am - 7:00 pm (IST)