How To
How To
1419 results
-
This is caused by the volume synchronizaton system in the iPad. When you switch off the iPad with click sounds activated, it sends the click sound to the Go+Play, also ordering the Go+Play to increase volume to maximum. The hiss is a result of the Go+Play Wireless being at full volume. As soon as you re-start your music playing from the iPad, volume is back to normal music use. If you do not switch the iPad on again, the Go+Play goes into standby after a few minutes, and the hiss disappears. You can prevent this problem by de-activating the click/alarm sounds on the iPad.Was this helpful? Thank you for your feedback!
-
Please check the picture settings on your cable box, particularly the aspect ratio settings, which will vary depending on the brand and model of your cable box and on your local cable provider. You may wish to consult with your cable provider for more information on how to adjust the cable box's settings. Some settings, such as a setting to force an analog channel's native 4:3 aspect ratio to 16:9 widescreen to fit your display, may interfere with the cable system's copy-protection feature and cause distortion.Was this helpful? Thank you for your feedback!
-
Yes it will.Was this helpful? Thank you for your feedback!
-
To set up the Harman Kardon Adapt in the HK Controller app, you have to select "One speaker", not the Adapt+ option. When selecting "One speaker", simply follow the on-screen instructions to install your Adapt on the Wi-Fi network. Note that the instructions for Adapt devices will appear on your screen after 30-45 seconds (Only Apple devices).Was this helpful? Thank you for your feedback!
-
The wireless charge receiver in the smartphone may not be adequately coupled to the wireless charging transmitter on Smartbase. Re-adjust your smart phone’s position on the wireless charge arm.Was this helpful? Thank you for your feedback!
-
The rechargeable AAA cells may of course be worn out, or they may not be installed at all. If this is the case, either insert the cells, or you can order new cells as original spare parts. Please contact Harman Helpdesk for your country, or the distributor for your country, for further info about how to buy new cells. Please note that the cells MUST be compatible with charging contact for the minus pole located on the side of the cell. Normal cells will not work. This is clearly mentioned in the owner's manual, and shown with a drawing. If you have purchased new cells with plastic coating along the length of the cell, it may be possible to peel off the coating by cutting gently with a knife, then peeling it off. Only about 1 cm needs to be open to the metal, closest to the flat end, for contact to be possible. Please note that the ear pads on K 912 are removed by simply grabbing the plastic plate that holds the ear pad, and pulling it away from the ear pod. There is one battery in each ear pod. For K 915, never just pull the pad away, since the locking claws are released by being rotated away from their locked position.. Both batteries are under the right-hand pad, and there is a silk-screened instruction on the top of the pod, showing that you must rotate the pad plate just a few mm counter-clockwise to unlock it.Was this helpful? Thank you for your feedback!
-
• Please check whether your head unit Bluetooth support EDR (Enhanced Data Rate) • If the head unit does not support EDR this will cause the transfer data rate to be low and will impact the audio quality.Was this helpful? Thank you for your feedback!
-
This problem is usually caused by pressing down too hard on the soundbar's VOL + or VOL - Buttons. Only press just enough for one click to be felt. If a second click is felt in the button, you are pressing too hard, and you are actually activating the MUTE function for learning, not VOL up or down. You may have to repeatedly let go of the VOL button on the soundbar, followed by pressing it again and then pressing the VOL button on the TV remote before the surround light on the soundbar lights up white and goes back to amber flashing, as a sign that this function has been learned. This is no problem, though. Just keep trying until the three commands have been learned. The soundbar only exits learning mode when you press and hold the surround button as the final step.Was this helpful? Thank you for your feedback!
-
Please note that the LFE Trim function is only active with surround source signals that feature a separate LFE track for the subwoofer. It does not affect subwoofer level when playing stereo or mono.Was this helpful? Thank you for your feedback!
-
When the speaker is switching quickly between music sources via Bluetooth, it's normal to experience a very short 'pop' sound because the Bluetooth signal is breaking in and doing the handshake with the speaker. It won't appear after the Bluetooth signal is stable.Was this helpful? Thank you for your feedback!
-
Yes, when changing volume to higher or lower, the LED will illuminate to show that you are changing the volume.Was this helpful? Thank you for your feedback!
-
The Normal and Pulsed DC triggers are active (on) when the No. 523 and No. 526 is on, they are not active (off) when the No. 523 and No. 526 is off. The Theatre DC trigger is present only if the current input is in SSP mode, otherwise this trigger is off.Was this helpful? Thank you for your feedback!
