How To
How To
1413 results
-
Power on the Flip 3 SE and press the Bluetooth button. The Flip 3 SE should be available in the list of Bluetooth devices on your mobile phone/tablet.Was this helpful? Thank you for your feedback!
-
The SB450 soundbar is paired to the subwoofer right out of the box. If the 2 parts are not already paired together, simply press the Pairing buttons on the rear panel of both products and they will connect with each other.Was this helpful? Thank you for your feedback!
-
1. Enter pairing mode and connect to device 1. 2. Enter pairing mode again and device 1 will disconnect. 3. Connect to device 2 and turn headphone off. 4. Turn headphones on and headphones will automatically connect to device 1 and 2 simultaneously. 5. Pause one device and play from the other to swap headphones connection. NOTE: Maximum number of devices that can be connected at any given time - 2 source devices.Was this helpful? Thank you for your feedback!
-
Hold the Power ON/OFF button down for >5 seconds. Status light will pulse White when headphones are in pairing mode. Release. Access Bluetooth settings on your source device. Locate "№ 5909" and connect. A solid white light indicates you are connected.Was this helpful? Thank you for your feedback!
-
Swift Pair is the newest way to pair your Bluetooth peripherals Windows 10, version 1803 or above.
Steps:
1. Put the Bluetooth peripheral in pairing mode
2. When the peripheral is nearby, your Windows device will show a notification
3. Selecting “Connect” starts pairing the peripheral
4. When the peripheral is no longer in pairing mode or is no longer nearby, your Windows device will remove the notification from the Action Center
Was this helpful? Thank you for your feedback! -
Short-press the Bluetooth Button to open for new pairing.Was this helpful? Thank you for your feedback!
-
Short-press the Bluetooth Button to activate pairing mode. Now set your device to scan for Bluetooth devices. It will find the BOOST TV and allow you to pair to it.Was this helpful? Thank you for your feedback!
-
During phone call, short press the Siri Access button shown in “quick start guide” section 6 to mute the microphone. A short press the same button again will un-mute.Was this helpful? Thank you for your feedback!
-
To ensure the best accuracy, it is important that you are using the proper size and the headphones securely fit in the ear. Please reference FAQ: How do I find the proper fit? to make sure you are wearing them correctly. You should also make sure that the enhancers are properly installed on the ear buds so that material is fully stretched over the bud and the window for the heart rate (HR) sensor is not covered. Please reference FAQ: How do I switch enhancer sizes? for more guidance. Once you've found your ideal size and ensure they're installed correctly, make sure the HR sensor is on. When it is on, you will see a green light on the LEFT ear bud and should hear the audio prompt stating, “Heart Rate sensor on”. For best results, insert the earphone into your ear so that the green heart rate sensor on the LEFT ear bud is fully hidden inside the ear (behind your tragus). Double check that the ear bud is touching the back of the bowl of your ear for the most accurate signal - this is often times achieved by using the largest size that fits comfortably in your ear. Lastly, the ear loop should not be pushed backwards to align with arc of the ear perfectly; it is likely there will be negative space between the headphone loop and your ear. You should hear the audible alert telling you if the ear bud needs to be adjusted if it is unable to retrieve a proper reading on your heart rate. Heart Rate accuracy can vary depending on the type of exercise you are performing; it is recommended for steady state endurance-oriented activities to ensure best accuracy. While the technology is state-of-the-art, there are limitations that may cause some readings to be inaccurate under certain circumstances. These circumstances include physical characteristics, fit, and the type of activity as outlined above. The heart rate monitor data is not intended to be used for medical purposes, nor is it intended to diagnose, treat, cure or prevent any disease or condition.Was this helpful? Thank you for your feedback!
-
Tap once on the JBL logo of the right earbud, then place your finger on the logo again, and hold it there for 5 seconds. You will hear a confirmation tone in the headphones when locking takes place. To unlock, close the power hook.Was this helpful? Thank you for your feedback!
-
When the headphones are charging, you will see a solid red light at the top of the inline microphone. When the headphones are fully charged, the red light will shut off. You should expect 8 hours of playback time. Please keep in mind that the level of volume can effect the longevity of the battery life.Was this helpful? Thank you for your feedback!
-
The Flip 3 SE has 5 white leds which shows the battery level when you power on the device. Each white led indicates around 20% battery level. When all of the white leds are off, and the last led is blinking red, you should recharge the battery.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Message Us
Chat with a support agent via Whatsapp at:
91 70658 44446
Mon - Sun: 10:00 am - 7:00 pm (IST)