Please check with your car manufacturer to ensure your car supports CAN or K-line. JBL DRG only works with CAN and K-line to get the engine data for engine sound simulation. If your car does support CAN or K-line, please launch the JBL DRG app and check the engine sound volume bar (the right column with button marked with “E”) in the “Sound Mode” section to make sure it is not turned off.

Please use an OBD II extension cable in this case. An extension cable is not included in the package but they are readily available for purchase on-line.

When you place the two Free earphones in the charging case, you will see a white led ring light up on both of them. At the same time, some of the four dot-leds on the charging case will light up to indicate the battery level of the case battery. When the earphones are fully charged, the white led ring goes out on each of them. When both are fully charged, the charging case charging level leds go out too.

The JBL Free automatically switches from stereo to mono when making or taking phone calls. Voice calls will only come through the right ear piece for a more natural call experience.

In the event that left and right ear piece pairing is lost, power on both ear pieces and press the buttons 3 times on each ear piece to initiate re-pair.

In the event that ear pieces do not re-pair automatically to paired Bluetooth device, power off ear pieces individually by press and hold the buttons for 5 seconds. To enter Bluetooth pairing mode when ear pieces are powered off, press and hold on buttons of both earpieces for 8 seconds. Re-pair the right ear piece with desired Bluetooth device when LED indicator on right ear piece alternates between blue and white LED lights.

The JBL Free X does not feature volume control. In order to adjust the volume, you must manually increase/decrease from your device.

You cannot download the JBL Portable App on a PC. This app is only available on mobile devices.

You can adjust Equalizer, Spatial Sound, RGB LED effects, change microphone settings and update the headset's firmware

You can clean it by wiping it gently with a damp cloth. Take extra care not to let water leak into the speaker chamber, as it will damage the speaker drivers.

The Checklist

Let us walk-through a list of things needed to ensure every requirement is met.

1. Check your mobile device if that is able to connect to same Wireless network.
2. Make sure you are within range of your Wireless router.
3. Check the Wireless signal on your mobile device, does it have a weak signal then move closer to the router.
4. Try both Wireless network bands 2.4GHz and 5GHz in case one of them are failing.
   1. You will have longer range with 2.4GHz, but less performance and most of the times a crowded network (many devices are using 2.4GHz band).
   2. You will have less interference with 5GHz and higher performance, however, the range of the 5GHz network has shorter range.
5. Try using a different mobile device, if you have one.
6. Reboot your Wireless network router and your mobile device.

Watch the video below for help with setting up your Google Assistant device.

Wireless Network Extender

Some houses or apartments can be too big for one Wireless network router to cover it all.
Let's talk about the issues that might appear with an Extender network.

1. Network Extenders that will help cover poor signal in your home, often results in poor connection and low speed performance.
2. Often the Network Extender is a low budget device or not suited for having too many devices attached to it.
3. Placement of the speaker is crucial as you can put it in a place where it could connect to either main Wireless router or the Extender, that will confuse Wireless network devices.
4. To solve this issue, try move the speaker closer to main router or have fewer devices attached to your Wireless Extender.
5. In addition, always use 5GHz connection between your Network extender and main router (best solution and performance).

One Wireless Network Name (SSID)

1. You may have set the Wireless Network SSID (Wi-Fi network name) to one big Wireless network (With a main router + Extender(s).
2. If the JBL LINK device is within range of both Wireless networks (Main router & Extender) then it can get confused with which one to connect to.
3. To solve this issue, using two different name for your extended network will help with the performance of the JBL LINK Speaker and Google Assistant request.

 

The Checklist

Let us walk-through a list of things needed to ensure every requirement is met.

1. Check your mobile device if that is able to connect to same Wireless network.
2. Make sure you are within range of your Wireless router.
3. Check the Wireless signal on your mobile device, does it have a weak signal then move closer to the router.
4. Try both Wireless network bands 2.4GHz and 5GHz in case one of them are failing.
   1. You will have longer range with 2.4GHz, but less performance and most of the times a crowded network (many devices are using 2.4GHz band).
   2. You will have less interference with 5GHz and higher performance, however, the range of the 5GHz network has shorter range.
5. Try using a different mobile device, if you have one.
6. Reboot your Wireless network router and your mobile device.

Watch the video below for help with setting up your Google Assistant device.

Wireless Network Extender

Some houses or apartments can be too big for one Wireless network router to cover it all.
Let's talk about the issues that might appear with an Extender network.

1. Network Extenders that will help cover poor signal in your home, often results in poor connection and low speed performance.
2. Often the Network Extender is a low budget device or not suited for having too many devices attached to it.
3. Placement of the speaker is crucial as you can put it in a place where it could connect to either main Wireless router or the Extender, that will confuse Wireless network devices.
4. To solve this issue, try move the speaker closer to main router or have fewer devices attached to your Wireless Extender.
5. In addition, always use 5GHz connection between your Network extender and main router (best solution and performance).

One Wireless Network Name (SSID)

1. You may have set the Wireless Network SSID (Wi-Fi network name) to one big Wireless network (With a main router + Extender(s).
2. If the Wireless speaker is within range of both Wireless networks (Main router & Extender) then it can get confused with which one to connect to.
3. To solve this issue, using two different name for your extended network will help with the performance of the Wireless connected speaker and Google Assistant request.

 

The Left and Right bud should sync together automatically when removed from the case. If the Left and Right bud do not sync together automatically within 15 seconds, you may manually sync the buds together. With the buds out of the case, press the center button on each bud 3x. This action does not have to be done simultaneously. You may start with either the L or R bud to initiate syncing.

The speaker is IPX5 certified, it can withstand direct splashes from any direction for up to 3 minutes. Although a little snow or rain won't hurt it, we do not recommend keeping the speaker outside during rain and/or snow. Also be aware of extreme hot or cold temperatures, they may be damaging.

Yes. You can configure the volume of the mic monitoring in JBL QuantumENGINE. And the default setting of the mic monitoring is set of “OFF”.

Yes. You can configure the volume of the mic monitoring in JBL QuantumENGINE. The default setting of the mic monitoring is "OFF”.

If the wireless mic is out of signal range, you will experience drop outs or no sound. Once range is reestablished, the speaker should automatically detect the mic and resume connection within less than 3 sec. 

When a wireless mic is connected, the speaker will play a notification sound once. If two wireless mics are connected at the same time, there may be a 1 sec gap between the two notification sounds. 

If one of the wireless mics is not working, we recommend the following: 

1. Turn off the speaker
2. Turn on the mic and place it on top of the speaker
3. Turn on the speaker
4. The speaker should automatically pair with the new mic within 3 min and play a notification sound 
 

1. Insert both earbuds into the charging case.
2. Try to click 5 times on both left and right earbuds button simultaneously, to reconnect left and right earbuds.
 

No, since the speaker does not store any information locally. To remove all settings from your stolen device, simply unlink the speaker from your account, and the next time the speaker goes online it will not connect to your account. However, if you have used the command ""Remember this"" feature, please beware of sensitive information, as the speaker will inform you of whatever you have asked it to remember. But after unlinking the speaker, it will forget.

If your Wi-Fi network name has special characters, such as (, `, \, ', ", or ), then please change the name of your Wi-Fi network, as these characters are not supported. After changing the name, you can go ahead and setup the speaker to your Wi-Fi network.

Dual band routers that have 2.4 and 5 GHz connection bands. If devices connect on different bands, they cannot see one another. Please make sure your phone and speakers are both connected to 2.4 GHz or 5 GHz and that there is no AP isolation activated between them.

One explanation can be that your OMNI 50+ is part of a 5.1 system with your Omni Bar, which will make the surround OMNI 50+ left and right rear speakers act as "secondary", and Bluetooth connection is not possible to secondary speakers. To use the OMNI 50+ as a portable speaker again, simply perform a reset of the speaker by pressing the reset button for 5 seconds. Please note that after resetting your OMNI 50+, it is no longer part of the 5.1 wireless system.

Do not worry, pairing both devices is easy and quick. Press the "pairing" button on the back of the Omni Bar, then press "pairing" button on the subwoofer. They will start communicating with each other, and when both devices show white light in the LED on the back, that indicates that they are paired.

Make sure the headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. Check that the correct playback device is selected under Control Panel > Sound > Playback. Select the correct device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.

Make sure the headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. If you're using the USB dongle, check that the correct playback device is selected under Control Panel > Sound > Playback. Select the proper playback device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.

Ensure that the correct device is selected as the default device under Control Panel>Sound>Playback. Make sure the on headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. Check that the correct playback device is selected under Control Panel > Sound > Playback. Select the correct device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.

Make sure the volume control on the headset is turned up. Rotate the volume wheel on your headset to increase the volume. If you're connected to the PC via USB, check that the default device is selected under Control Panel > Sound > Playback. Select JBL Quantum 600 or Quantum 800 Game, right-click, and select "Set as Default Device". Check your headset's game-chat balance dial and ensure that the balance is correct. Check the JBL Quantum 600 or Quantum 800 Game device and make sure it is not muted or turned all the way down.

What you need first

Make sure that the device is installed on your Wireless network, by ensuring these steps below:

1. You have the most recent version of the Google Home app installed 
2. Your Citation device is powered on
3. Your Citation device is plugged into a wall outlet.
4. The Citation device is located near your router 
5. The white LED lights in front of the Citation device are blinking 
6. If you are using an Apple iOS device, you need to turn on Bluetooth to installed the device.

   1. On your iOS device Home screen, tap Settings > Bluetooth 

   2. Make sure Bluetooth is on
   3. Return back to the Google Home app 
   4. Your Citation device should appear as "Set up this device"
7. If you are using an Android device, you need to turn on Bluetooth and Location Services.
   1. On your Android device, tap Settings.
   2. Find Bluetooth settings > Make sure Bluetooth is on
   3. Tap Location > Turn on location 
   4. Tap Settings > Apps > Google Home app > Permissions.
   5. Next to "Location",  check the slider is on.
   6. Your Citation device should appear as "Set up this device" .

If you are still having trouble discovering your Citation devices in the Google Home app, follow the steps below for further troubleshooting.

Troubleshooting

Step 1. Reboot your Citation device 

1. Disconnect the power cable from your Citation device 
2. Reconnect power cable to your Citation device 

Step 2. Force close and relaunch the Google Home app      

1. From your Apple iOS device, do the following below:                   
   1. Press the Home button two times quickly. There will be a small preview of your recently used apps.      
   2. Select the app you want to close and swipe up towards the top of the screen.
   3. Launch the Google Home app again.        
2. From your Android device, do the following below:              
   1. Launch the Recent Applications menu to see small previews of your recently used apps. The Recent Apps button, a square icon, should be accessible at nearly any time along the bottom of the screen along with the other buttons on the virtual task bar.
   2. Select the app you want to close and swipe left or tap the X.
   3. Launch the Google Home app again.

 

Last thing to try​ 

If you are still experiencing issues with your Citation device not connecting to your Wireless network, try the following:

1. Try finding another mobile device to set up your Citation device, sometimes it can help connecting your speaker 

2. Relocate your Citation device, or try to disable other Wireless network devices that might cause interference for your Citation device.

3. Perform a factory reset of your device, by holding down the reset button for more than 5 seconds.
4. Reboot your Wireless router           
5. Lastly, try turning Wi-Fi off and then back on again on your mobile device. Reopen your Google Home app and try again.

- Try to disconnect some devices from your Wi-Fi network. Some routers may have weak performance, which can cause issues and poor connection to all devices in your network. - If your router supports 5Ghz ( 802.11N or AC ) and you have devices that are capable of using 5 GHz Wi-Fi then switch to that specific network for best performance. - If you have a lot of ( Legacy / older than 5 years ) devices on 2.4GHz network, try limiting them to max. 6 connected simultaneously

It is possible to pair two of the same model of JBL PartyBox speakers together through TWS (True Wireless Stereo) mode.

PartyBox On-The-Go/100:
Connect just the left PartyBox with the chosen device first, with the right PartyBox turned off. The speaker that is connected first will automatically be the left channel. Now turn the right PartyBox on and continue with TWS pairing (detailed below).

PartyBox 200/300/1000:
A button (L/R) on the rear of the speakers is used to assign the correct channel to the speakers after pairing is made.
In order to activate TWS mode, press and hold the Bluetooth button on the first speaker until the notification chime sounds, about 5 seconds. Then press and hold the Bluetooth button on the second speaker until the notification chime sounds (as seen below). TWS mode is now activated. To disable TWS, press and hold the Bluetooth button on either speaker, or power off one speaker.

Partybox 110/310/710/Encore/Essential:
Press the buttons labelled TWS on both speakers to connect the speakers in TWS mode (pictured in item 2 in the image below, with two speakers on the button).

TWS can be activated and deactivated remotely in the JBL Partybox app, in addition to assigning the left and right channels to the correct speakers.
Once the TWS connection is setup, it will be in Stereo mode by default if both speakers are the same model, otherwise the speakers will be in Party mode by default if different Partybox models are used. You can also switch between Stereo and Party mode in the JBL PartyBox app if two of the same Partybox models are used.

Please note: In order to achieve TWS mode, the speaker must be the same model with the exception of the PartyBox 200 and PartyBox 300 which can be paired together via TWS. You cannot achieve TWS with a PartyBox 1000 and a PartyBox 300. You cannot achieve TWS with a PartyBox 100 and PartyBox 200. However, it is possible to connect a maximum of two of either the Partybox 110, 310, 710 or Encore/Essential together in Party mode - the two speakers then do not need to be the same model, but Stereo mode will not be possible.