Yes. This product has a microphone.

No, each headset must have its own transmitter. However, even if you try to use more than one complete set of 915 in the same room simultaneously, it may not work either. Although the 915 has an automatic scan function that finds available slots in the 2.4 gHz transmission frequency band, interference may still occur.

It is possible to connect both HDMI and optical to the TV input at the same time, but HDMI will be prioritized over optical. Switching manually from HDMI to optical is not possible.

Yes, you can use the headphones, but of course the noise cancelling will not be active.

Yes, you do not need to have music playing to keep the noise cancelling switched on. There may be a slight residual hiss from the NC system, which would usually be masked by music, but there will still be a significant reduction of external noise.

Yes, this is no problem.

Streaming via Bluetooth or direct aux in connection are supported without the HK Controller app. For OMNI+ devices that you already have placed in a room, they are capable of using either Spotify Connect or Chromecast built-in without the need of using the HK Controller app. Use only the HK Controller app for setting up any OMNI+ devices you may have.

Yes, you can activate the noise reduction circuits alone, with no connection to a source device by Bluetooth or cable. The headphones will stay on as long as there is power in the battery, which is close to 30 hours for pure NC function. Please note that there is a slight residual noise from the NC system, which will be drowned out by music playing, or by surrounding noise such as airplane noise. If you use the NC in surroundings that are near quiet to begin with, you may not get an improvement in noise level.

Yes, this is no problem.

Yes, no problem.

Yes, press and hold the remote button with the round dot (between volume up and volume down) for for about three seconds. Your iPhone will confirm with a tone that SIRI is ready for voice input.

Yes, but only with music via cable, and noise reduction will not be active. As soon as you insert the charging cable micro-usb plug, the Bluetooth and NC functionalities will be switched off, and they cannot be reactivated unless you remove the charging cable, and there must of course be a charge in the battery. If you listen to cabled music while charging, be prepared to hear noise under certain conditions. Both computers and switch-mode power supplies can be very noisy, and this noise can sometimes be heard as a whine or buzz. This can only be eliminated by using a power supply that does not create noise.

Yes, the Arena Sub 100P can be used in multiple regions. The subwoofer’s power requirement ranges from 100 volts – 240 volts, 50/60 hertz. As long as you have an adapter to properly plug the speaker into various wall outlets, the Arena Sub 100P will work anywhere in the world.

Only Bluetooth pairing can be used for JBL Connect on Boost TV.

Yes, in case your Wi-Fi does not work then simply press and hold the Bluetooth button for 3 seconds, your speaker is now in pairing mode. The button is located on the back where you connect the power cord. Please be aware that Alexa will not work on Bluetooth.

No. The only way that the Noise Cancellation feature can be activated is while you are using the headphones wirelessly. You cannot use NC while the headphones are plugged into a device or charging.

The Game-Chat balance dial only works when your headset is powered on. Please note that it supports connection with a USB Type A to C cable and a wireless transmitter dongle, but doesn’t support connection through a 3.5mm cable or Bluetooth for mobile games.
The Game-Chat balance dial is compatible with PC and Mac, but not with PS4 I 5, Xbox Series X | S, Nintendo Switch or Mobile.

The Game-Chat balance dial only works when your headset is powered on. Please note that it supports connection with a USB Type A to C cable and a wireless transmitter dongle, but doesn’t support connection through a 3.5mm cable or Bluetooth for mobile games.

The JBL Quantum 800 can only be used via a 3.5mm, Bluetooth, or 2.4Ghz wireless connection.

There is a buffer inside the speakers that processes the incoming signal. This buffer delays the audio signal compared to the video signal, causing a delay. For this, we do not recommend using Omni+ speakers with a TV. Our Omni bar will work with your TV sound and you can create wireless 5.1 surround sound system with the Omni bar.

Unfortunately, the OR100 are specifically designed for the Oculus Rift only. You cannot use these headphones on other devices.

No, the OR 300 headphones are specifically made for the Oculus Rift. These headphones will not work with any other device.

Yes, all sources that output analog stereo line-level signals or stereo audio optical digital signals may be used, cable-connected to the BTA 20 transmitter. Digital signals must be in PCM format. So if you have a CD player or an FM radio, you can connect the BTA 20 to it, and transmit to your Soundgear (or to other Bluetooth headphones that support the format). Please note that record players need an additional preamplifier to work this way. Of course a TV set can be connected as well, either via optical digital PCM output, via line outputs or via headphone output.

Yes, however, the JBL ONE App gives you another level of control over the speaker/soundbar.
Through the App, you can personalize the performance, such as:

• Customizing EQ settings
• Setting up our new feature called: My Moment 
• Connect your favorite streaming music services.

Yes, you can easily charge your OMNI 50+ while charging another device via USB port.

-       No, your Voice Assistant operates in the cloud and needs to be connected to the internet. .

No, only analog audio sources are available for Zone II.

Although the product is Water Resistant and Sweat Resistant, continuous exposure to water over an extended period of time may damage your earphones.

Although the product is Water Resistant and Sweat Resistant, continuous exposure to water over an extended period of time may damage your earphones.

No, JBL Flip 4 can wirelessly link with JBL Connect+ compatible speakers only. Currently, the Flip 4, Pulse 3 and Charge 3 ( after a firmware upgrade ) have the JBL Connect+ feature

Yes, you can use your Soundgear for TV watching or playing video games. You can use the TV speakers and the Soundgear simultaneously, they will be synchronized in time.

These units do not offer multi-voltage power supplies. However, you can use a domestic 110 volt component overseas with the addition of a step-down transformer, available at most electronics stores.

Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 

No, you cannot use a lightning connector to charge the N90Q. It can only be charged with the micro USB charger that is provided for you in the packaging. Also, no digital signal transmission can take place from an iPhone, only from Android phones. But some Apple computers will work.

No, this is not possible. The N90Q is completely self-contained. Also, it is not a Bluetooth headphone.

Yes, you can listen to the N90Q while they are charging at the same time. Please note that the two cables need to be connected at the same time if you are listening to analog sound. When using digital sound input through the USB cable, charging and digital transmission take place simultaneously.

No, since this is a fully active headphone, power is necessary. The extra power pack is included to give extra safety.

What you need first

Make sure that these below things are checked before moving further:

1. You have the most recent version of the Google Home app installed 
2. Your LINK device is powered on (LINK 10 and LINK 20 with battery)
3. Your LINK device is plugged into a wall outlet (LINK 300, LINK 500 and LINK VIEW)
4. The LINK device is located near your router and you are standing next to it. 
5. The white LED lights in front of the LINK device are blinking, meaning it is ready to be set up
6. If you are using an Apple iOS device, then you need to turn on Bluetooth to install the device

   1. On your iOS device Home screen, tap Settings > Bluetooth.

   2. Make sure Bluetooth is On (toggled to the right and green).
   3. Return back to the Google Home app .
   4. Your LINK device should appear as "Set up this device" and you can continue with installing the LINK product.
7. If you are using an Android device, then you need to turn on Location services
   1. On your Android device, tap Settings .
   2. Tap Location > Turn on location.
   3. Tap Settings > Apps > Google Home app > Permissions.
   4. Next to "Location",  check the slider is On (toggled to the right and green)
   5. Your LINK device should appear as "Set up this device" and you can continue with installing the LINK product.

If you are still have trouble with installing your LINK devices then follow the steps below for further troubleshooting.

Troubleshooting

Step 1. Reboot your LINK device

1. Disconnect the power cable from your LINK device (300, 500 and VIEW) and for LINK 10 and LINK 20 simply turn the device "OFF". 
2. Reconnect power cable or turning the device ON for your LINK device. 

Step 2. Force close and relaunch the Google Home app      

1. From your Apple IOS device, do the following below:                   
   1. Press the Home button two times quickly. There will be a small preview of your recently used apps.      
   2. Select the app you want to close and swipe up towards the top of the screen.         
2. From your Android device, do the following below:              
   1. Launch the Recent Applications menu to see small previews of your recently used apps.                                 
   2. The Recent Apps button should be accessible at nearly any time along the bottom of the screen along with the other buttons on the virtual task bar.

Step 3. Check to see if the device is listed under “Ignored Devices” folder on the Devices tab      

1. Open the Google Home app.
2. In the top right corner of app home screen, tap Devices.
3. Scroll all the way down and make sure the LINK device is not listed under the Ignored Devices section.
4. NOTE: If you do not see any ignored devices, there is a chance that this section is not listed in the Google Home app.

Last thing to try​

If you are still experiencing issues with your LINK device not connecting to your Wireless network, then try the following:

1. Try finding another mobile device to set up your JBL LINK device, sometimes it can help connecting your LINK device.

2. Relocate your LINK device, or try to disable other Wireless network devices that might cause interference for your LINK device.

3. Perform a factory reset of your device, by holding down the mute button for 15 seconds (the LINK will now reboot and when the welcome message is heard then you can set it up again).
4. Reboot your Wireless router.           
5. Lastly, try turning Wi-Fi off and then back on again for your mobile device. Reopen your Google Home app and try again.

This is not supported at this time, but the upcoming Omni+ speakers will support Google Chromecast built-in, which has support for many Internet radio services such as TuneIn Radio.

The functions that can be programmed from your TV remote control into Boost TV are Volume+ and Volume-, Mute and Power. No other functions can be learned.

Yes, the two model 300 versions are of identical size, and so are the two model 700 versions. The carrying cases can be purchased as spare parts.

No. The case can only be used to carry the speaker.

The Everest 300 ear pads can be replaced by owner, but it is not easy, and removing the old pads may damage them. So, it is not a bad idea to have new pads at hand before removing the old ones. Since they are glued in place with double-adhesive tape, it is necessary to rip them off with care. After removing the old ones, clean off any residue of the double-adhesive tape that held them in place from the headphone pods. Then remove the protective layer on the new pads, exposing the adhesive. Carefully align the new pad before pressing the edge. This is to prevent the glue from sticking before you get the pad into the right position. When the pad sits correctly, you can press the edge all the way round to make the adhesive stick securely.

Yes, both ELITE 300 and 700 can do this.

The headphones can pair to multiple devices but can only be connected to one device at a time.

Yes, unlike many other Noise Reduction headphones, the N60 will play music, even when the battery is empty. Of course, Noise Cancellation will not be active.

Yes, the headphone will still work as a pasive headphone.

The JBL Endurance SPRINT, JUMP and DIVE can be used in salt water (i.e. sea) but we recommend to thoroughly wash the headphones in fresh water after every use in salt water, to remove the salt residue. Please note that only DIVE can actually be used in water, because it features a function lock and a built-in memory for MP3 music files. SPRINT and JUMP cannot be used in water, because the touch buttons will malfunction when submerged, and Bluetooth cannot function at all under water.

Because bluetooth cannot travel through water, the only Endurance model that is used for swimming is the Endurance DIVE model. The Endurance DIVE model features an MP3 player which allows you to listen to music under water without using bluetooth. Furthermore, only DIVE features a function lock, which prevents water from activating functions inadvertently. SPRINT and JUMP do not have this lock function, and will not work under water.

No, as soon as charging begins, the headphone shuts down. Since no option for cabled listening exists for this model, it is necessary to charge before listening is again possible.

No, this is a Bluetooth only headphone. Charging is done with cable, of course, but there is no cabled audio connection.

Yes, the transmitter / charging dock is designed to be easily hung on a wall with just two screws. Of course the headphone can be charged in this position also.

The carabiner can be removed from Clip 2 and can be purchased as a spare-part.

Yes, you can use cabled audio connection instead of Bluetooth on the N60NC Wireless, if you prefer. You can listen to a cabled source even if the battery is empty, but the noise cancelling function will of course not be available in this case. If the battery is charged, you can switch noise cancellation on or off at will. You do not have to have a cable connected at all. You can use the headphones as noise cancellers just by putting them on, and switching NC on.

Yes, but only with certain Android telephones. It is not possible to use iPhones. It is necessary to buy a USB 2.0 cable with Micro-B male plug to Micro-B male plug, OTG functionality. (On-The-Go). This cable is available in different lengths from various electronics shops or web shops. Connecting the telephone and the N90Q with this cable will usually open for digital signal transmission immediately, and the amber charging button on the N90Q will light up as an indication of open connection. (Please note that N90Q can play digital signals from some Apple computers, Macbook, iMac etc.)

No, the No. AUX outputs cannot be used for any Atmos channels.

It is safest is to turn amplifier off, change the switch position, then turn the unit back on. The switches should not be changed if the unit is ON (operate mode), they can be changed if the unit is in standby but only if the standby mode is Green or Power Save.

Since this headphone has Lightning connector, it cannot be used with any Apple product that does not have this connector. Also, it is necessary to use the My JBL Headphone app to play through the headphone, and to be able to control it. This means that only sources that permit the use of apps can be used. This will exclude use of iPod Nano. And of course iPod Shuffle cannot be used, since it has no Lightning connector. IPod Touch works fine, as does iPhones and iPads with Lightning connectors.

The Everest product uses standard Bluetooth protocol for audio communication. Gaming headphones usually use a different frequency and protocol for audio communication.

Yes, the click-on connector that holds the earphone in place on the Oculus Rift is adjustable in small clicks, longer or shorter.