How To
How To
1867 results
-
The most important thing, is to be sure that both blue LEDs must flash quickly, one on the center speaker, one on the subwoofer. If just one of these LEDs does not flash quickly, pairing cannot take place. If it is difficult to make one of the LEDs change to quick flash, it may be that the button is held too long, or not pressed in the right angle. Try again with a short, firm press less then a second.Was this helpful? Thank you for your feedback!
-
Unfortunately, some Huawei phones are not able to stream music from the HK Controller app to 1st generation Omni speakers. However, the new Omni 10+, 20+, and 50+ have fixed this issue, and you will be able to stream music to them using your Huawei phone.Was this helpful? Thank you for your feedback!
-
Make sure your source device and AURA are on the same network. Then make sure your router is set to support older Wi-Fi protocols, such as b/g where the AURA is operating. Some routers have a function to disable older protocols and only use newer ones.Was this helpful? Thank you for your feedback!
-
It is not possible to setup a speaker to a hidden SSID Wi-Fi network. Please make it visible to install your OMNI+ speakers.Was this helpful? Thank you for your feedback!
-
It is not possible to use the speaker while installing it to your WiFi network. Once you have successfully connected to the WiFi network, you can use Bluetooth and AUX again.Was this helpful? Thank you for your feedback!
-
Your device has entered full standby-mode, which means it shuts down all activity to have the lowest power consumption. This is a requirement for any product in Europe in order to reduce power consumption for devices in your home. To use the HK Remote app again, simply switch ON your device with the original remote control or the front panel on/off button.Was this helpful? Thank you for your feedback!
-
What you are experiencing is normal. The JBL Free will automatically switch to mono mode on the RIGHT ear when the call starts. After the call ends stereo music mode will automatically resume.Was this helpful? Thank you for your feedback!
-
Android N, version 7.0 may have some compatibility issues, that are resolved with Android version 7.1. If your device is running Android N 7.0, please update it to 7.1 which should fix your issue.Was this helpful? Thank you for your feedback!
-
The registration success rate and quality of voice commands depends on the performance of your smart phone’s microphone. Make sure that your smart phone’s microphone is unobstructed and you are speaking clearly when registering commands. If you continue to have issues, try registering using a family member or friend’s smart phone as a test. If voice command registration is successful with their device, the microphone on your smart phone may have issues.Was this helpful? Thank you for your feedback!
-
Make sure your smart phone supports BLE (Bluetooth Low Energy) and it is connected to Smartbase via Bluetooth.Was this helpful? Thank you for your feedback!
-
Make sure the optical connection is seated securely on the SB250 and on your device. Go into your device settings and make sure the digital output is enabled. On TV displays the option usually states "enable external speakers" or enable "digital audio output".Was this helpful? Thank you for your feedback!
-
Make sure the optical connection is seated securely on the SB200 and on your device. Go into your device settings and make sure the digital output is enabled. On TV displays the option usually states "enable external speakers" or enable "digital audio output".Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call Us now at:
(877) 871-6755
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat with Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)