Unless the two remote controls are identical, you can only assign one remote control at a time to the SB16.

1. Make sure all wall and power outlet switches are on, and that all switches for your speaker system are on. Switch mains power to the system on/off by pressing the bass speaker volume button located on the back of the subwoofer. This button acts as power button when pushed in. 2. Ensure that the input jack is pushed all the way into the output socket on the source device. Check all the connections and secure them. 3. Your volume settings are too low or muted. Increase your volume by pressing the + key located on the right satellite. You can also check volume from your source device. If you are using a computer, check the volume control located in the taskbar, as well as the volume control in the media player or browser. This will mean a total of three volume controls in your computer alone. 4. To mute and unmute the speakers, touch the shining + and - controls on the right-hand "stick" at the same time. Only a slight touch is needed, since these are purely electronic touchpads.

Please keep the app running during a firmware upgrade. This is because the app is using BLE to transfer firmware to the JBL DRG. If you exit or kill the app, this will cause the BLE connection to be broken and the upgrade will not complete.

To use the Spotify Connect feature for JBL Playlist, a premium Spotify account is required. Please visit www.Spotify.com/freetrial for 30 days of complimentary premium account trial for first time users.

JBL DRG will auto reconnect to the last device. To setup a connection with new Bluetooth head unit, press the “reset” button in the App. The device will then search for a discoverable Bluetooth connection and setup.

If you require technical assistance, please contact NAVDY customer support at https://www.navdy.com/ Scroll down to the bottom of the website and select "Support" This navigates to the NAVDY HELP CENTER, where you can access FAQs, video tutorial, and live chat service.

Close and reopen the app. This will ensure that the app recognizes the headphones.

The upgrade via HID tool will only update the Bluetooth module inside of the BDS device. There are two ways of upgrading your system. 1: Upgrading Bluetooth via HID Tool. 2: Upgrade BDS firmware via the built-in software center. The built-in software center will not upgrade your Bluetooth module.

Our ESQUIRE2 support A2DP Audio codec, which you will need for your MAC to be able to play to our ESQUIRE2.

Make sure you disable AP/Client isolation on your Access Point / Extender and that Multicast forwarding is not disabled between the W-Fi networks. However, we cannot guarantee than streaming will work flawless as Extender networks are tricky and can cause many issues. Always use a 5GHz Wi-Fi network extender for best results.

We do not recommend using WEP encryption method, as this can leave your Wi-Fi vulnerable to outside threats. Our OMNI+ does not support this encryption type, we are supporting WPA and up.

The power on/off symbol/button will flash red consistently.

The power on/off symbol/button will flash white consistently. The LED switches to OFF when charging is complete.

The JBL Charge 3 has a battery level indicator, which consists of 5 LED's and display battery level.

When all 5 battery level indicator led's are illuminated solid white.

The 4 LED's on the front of the unit will light up.

It is offering low-latency wireless connectivity via a 2.4Ghz signal that is enabled by a USB dongle included in the box. Turn on the slider, then it automatically connect to the dongle. If you loss the connectivity with the dongle, power on with the slider and hold on for 5 seconds and press and hold the dongle to make sure the pairing until listening to the tone.

Before you start

• Remove any interference that might be blocking the Soundbar side-firing speakers.
• Any ambient noise or sounds that could disrupt the calibration needs to be out of the room.
• In case you are moving the Enchant Soundbar you will need to calibrate the sound again.
• If something went wrong, you can always delete the calibration settings by resetting the system.
  • Press and hold button and  button down for 5 seconds.
  • This will delete all settings, including the Wi-Fi connection.

How to use the MultiBeam feature

1. Press and hold the CALIBRATION button for 3 seconds.
   1. On the Enchant display a timer will start counting down from 3 to 0 (Once hitting 0 the Calibration will begin).

2. The calibration takes around 60 seconds before it is complete. While calibrating you will hear some noises coming from the speaker.
3. When finished the display on the Enchant Soundbar will say "DONE"

 

Smart pass-through charging helps you boost your device and power bank simultaneously through one wall outlet.

Here is how it works:

1. Plug your power bank into a wall charger.
2. Connect your device to the power bank (using the integrated cable or connecting a cable to it).
3. Press the power button on the power bank to trigger charging if your phone/device doesn't indicate it is charging.

For airplanes or analog listening, plug 3.5mm audio plug into headphone audio input to engage passive (wired) audio.
The headphones will power off when the audio cable is plugged in.
Passive audio listening will work even if the battery is depleted and the microphone and buttons are disabled during the passive mode.

NOTE: The No 5909 is only compatible with Mark Levinson's proprietary passive audio cables.

After setting up Google Assistant on your headphones through the My JBL Headphones app, use Google Assistant by pressing & holding the touch panel for 2 seconds on the earbud that you enabled the voice assistant feature on.

Press and hold the Action button to begin. Requires pairing with eligible phone and internet connection. For examples of questions and things you can do, visit: https://assistant.google.com/platforms/phones/#headphones

Get your notifications
Double-tap the Action button.

Stop your Google Assistant
Touch the Action button.

Reply to the message (where available)
After receiving a message notification, touch and hold the Action button to respond. When you’re done, release the button.

For more information on what your Google Assistant can do, visit: https://assistant.google.com/platforms/headphones

 

This video shows how to use a smart speaker that has Google Assistant built-in.
Our LINK series have Google Assistant built-in therefore you can practice your voice commands together with Harman/Kardon Citation or JBL LINK products

Press and hold the voice button while talking, then release the button to trigger. Requires pairing with eligible phone and internet connection. For examples of questions and things you can do, visit: https://assistant.google.com/platforms/headphones

Get your notifications

Tap and hold the voice button without talking, then release the button

Stop your Google Assistant

Touch the voice button once.

Reply to the message (where available)

After receiving a message notification, touch and hold the voice button to respond. When you’re done, release the button.

After setting up Amazon Alexa on your headphones through the My JBL Headphones app, use Amazon Alexa by pressing & holding the touch panel for 2 seconds on the earbud that you have enabled the voice assistant feature on.
 

Things to try

• “What’s the weather?”
• Play Niall Horan
• Play NPR on iHeartRadio
• Set a timer for 5 minutes
• What new skills do you have?

Stop Alexa when she talks
While Alexa is talking, press and release the Action button then say “Stop”.

For more information and things to try with Alexa, visit: www.amazon.com/alexadevices

1. On an Android or iOS device, add the Soundbar to your home WiFi network through the JBL BAR Setup App.
2. Follow the App instructions to complete setup.
3. Sign in with your Amazon Alexa account. If you do not have, create one.
4. With the Alexa MRM multi-room music playback, you can stream music on your Android or iOS devices to multiple Amazon Alexa speakers.

The remote control included with your LINK BAR can be updated, if a new version becomes available for your device.

There are two ways to find out if an update is available.

• A notification on your Android TV screen will appear. When clicking on it with your remote, more information will pop up.
• Manually check for an update, in case you have dismissed the notification, or the system does not show it.

Checking for update
To manually check for an update, please follow the instructions.
1. Go to "Settings" on your Android TV (ICON)
2. Find Connected Devices
3. Click on LINK BAR Remote
4. Under the Update firmware, if there is an update available, you will see it under the name.

The latest firmware version for your remote control is 1.27 (Changes to firmware numbers will change in the future).

5. Confirm the update for your remote control. The system ill download the files, and automatically start to update your remote.
5.1 NOTE: The battery needs to have more than 20% power left. If your remote is under 20%, you need to change the batteries, as this may break the remote control device.
6. When the update is ongoing, you must keep the remote control near the LINK BAR. This is because the remote is using Bluetooth to communicate with the system, and updating the device happen through Bluetooth connection. The update may take around 10 minutes or less.
7. When update is complete, this message "Remote is up to date," is visible, and you have the latest firmware.

You can update our Quantum 600 and 800 using the QuantumENGINE software on your PC.
To update the headset, go to SYSTEM SOFTWARE tab, find section HEADSET, and press CHECK FOR UPDATE and then INSTALL UPDATE.

To turn on/off the TV, the recommended control is “OK Google, turn on”/”OK Google, turn off.”

Note that this depends on your TV manufacturer and if they support this via HDMI CEC (This works only for HDMI connection).

1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).

Press and hold the Lightshow button for more than 2 seconds to turn off the Lightshow.

Once an alarm is set and starts to ring, it can be snoozed by tapping the large central knob/button on the top of the unit (circled in yellow in the image below). If this button is held for more than 2 seconds it will turn off the alarm.


The duration of the snooze cannot be changed and is fixed to 9 minutes. The alarm will continue to ring for 3 minutes and if not turned off or snoozed, it will automatically snooze after this time. It will automatically snooze for a maximum of 3 times, but if the snooze button is used before this occurs, the alarm can be snoozed an unlimited number of times.

Once snoozed, the display shows the time that the alarm will next ring.

To keep the radio playing after the alarm is turned off, press one of the 3 preset buttons or the DAB/FM button as desired.

Troubleshooting on a Wi-Fi Network:

1. Unplug your router, then plug it back in.
2. Give the router a minute or two to start up again.
3. Make sure your phone, tablet, or computer has reconnected to the correct Wi-Fi network before checking the SmartThings app again, making sure not to connect to a guest network, as this can prevent your devices from connecting to your speaker.
4. Use the router’s default “WPA2” security setting. Do no use “WEP” security setting on the router as this is not supported to connect your speaker with the internet.

Troubleshooting with ethernet:

1. Check the ethernet cable to make sure that the ethernet cable is firmly plugged in to both the router and your speaker.
2. If possible, try connecting the ethernet cable to a different port on the router.
3. You can also try using a different ethernet cable to make sure that the cable is not faulty.

The voice assistant you select in the initial set-up (pictured below) will be used as the default assistant on your headphones.



You can change the default assistant in the ‘My JBL Headphones’ app:

1. Open the My JBL Headphones app on your device.
2. Select the headphones you are connected too.
3. Go to Settings by clicking the symbol in the top right corner.
4. Select Voice Assistant.
5. Now you can select your preferred voice assistant.

Your headphones may restart after switching Voice Assistant.

Yes, you can adjust the game and chat audio balance by rotating the dial-up and down. When you rotate the dial, you'll feel a notch that indicates the balance is 50% game and 50% chat. The slider on Quantum ONE is different and has no notch but instead a visual indicator.

Onboard Active Noise Cancelling is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SINGLE press the ANC button to toggle it On/Off  and LONG press to active TalkThru. Turn on ANC again by a single press on the multi-function button.

Our new JBL Link Music and Link Portable both support Apple AirPlay 2. Pick up your Apple device, use your favorite music streaming service, and connect to the JBL speaker! Please note: before using Apple AirPlay 2, you will need to install it on your WiFi network, either using the Google Home app or Apple Home app ( your choice! ).

To show the current firmware version on your JBL TUNER device, go through the following steps.

1. Turn on the JBL TUNER.
2. Press and hold this three-button combination: DAB/FM+ Volume+ and Preset 5, simultaneously for 3-4 seconds.
3. In the display, you will see a combination of letters and numbers. This is the current software version.
4. See picture below as illustration.

The new firmware version released is V.0.0.57 (shown in the picture above).
To get the latest version, ask our customer service for a guide and an upgrade file.

 

Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.

Check that the PC is using the correct recording device.

1. Go to Control Panel

2. Select  Sound 

3 Select  Recording

4. Make sure to select the proper recording device.

1. Right-click on it Quantum headset.
2. Now select "Set Default Device" or "Select Default Communication Device"

5. Check the microphone levels by right-click on your Quantum headset.

6. Go to Properties

7. Chose Levels and adjust accordingly

Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.

Check that the PC is using the correct recording device.

1. Go to Control Panel

2. Select  Sound 

3 Select  Recording

4. Make sure to select the proper recording device.

1. Right-click on it Quantum headset.
2. Now select "Set Default Device" or "Select Default Communication Device"

5. Check the microphone levels by right-click on your Quantum headset.

6. Go to Properties

7. Choose Levels and adjust accordingly

Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.



How to check your PC settings for the correct recording device
1. Go to Control Panel

2. Select Hardware and Sound

3. Click on Sound

3 Select  Recording


4. Make sure to select the proper recording device.

1. Right-click on it Quantum headset.

   

2. Now select "Set Default Device" or Select "Default Communication Device"

   

5. Check the microphone levels by right-click on your Quantum headset. Then click on Properties


6. Choose Levels.


7. Adjust accordingly.
 

Please also make sure the volume control on the headset is turned up. Rotate the volume wheel on your headset to increase the volume.
Check that your headset's Game-Chat balance dial and ensure that the balance is correct, you might refer to the screenshot below from the QuantumEngine PC software.


If you still cannot hear the game or music audio, or if the volume is still very low, check if the TalkThrough is activated via the QuantumEngine software.


Finally, you can also do a short press on the Smart Ambient button on the headset (if your headset, has this feature)

1. Power on your JBL LINK speaker.
2. Verify that you are connected to the right Wi-Fi network on your smartphone.
3. Open your Google Home app .
4. Enable Bluetooth
5. Enable Location Service (Android Only)
   1. Make sure you have permitted the Google Home app to view your location.
6. First option Tap Add Set up device Set up new devices in your home
7. Second  option Tap X device found Select Home location
8. Follow the instruction on screen to add your new JBL LINK speaker.

You are now all set and can enjoy your LINK device!

Download the Google Home app, available for iOS and Android versions. 1. Open the Google Home app. 2. Plug in power for your Enchant 800 or Enchant 1300 Soundbar. 3. Enable Bluetooth. 3.1. Enable Location service on your phone and permit Google Home app to view your location (Android only). 4. Click setup device in your Google Home app. 5. Follow the instructions provided in the app, and enjoy Chromecast streaming for your Enchant soundbar!

Connect the headset to your PC via the 2.4GHz USB Wireless connection and ensure that you set your Quantum 910 Wireless headset as the default device especially before enabling the JBL QuantumSPATIAL 360 if you haven't installed the QuantumENGINE yet. You can check that the default device is selected under Control Panel > Sound > Playback. Select JBL Quantum 910 Wireless Game, right-click, and select "Set as Default Device" 

The Citation product with Airplay 2, use an iOS feature named Wireless Accessory Configuration (WAC), which is the easiest way to set up Wi-Fi for iPhone users. If you want to set up AirPlay with WAC and set up Google Assistant later, you can follow the below instructions.

1. Go into the Wi-Fi settings on the iPhone/iPad
2. Select the speaker you want to set up AirPlay under “SET UP NEW AIRPLAY SPEAKER...” on the lower part of the display.
3. Choose the Wi-Fi network you want to connect this speaker to, then press Next. This should normally be the same network your phone is connected to, which will appear as the default option.
4. The speaker will connect to the Wi-Fi network. Press Done to finish the setup.
5. After setup is successful. You can tap the Airplay symbol in Control Center or from your favorite audio streaming app to use AirPlay from your iPhone and iPad.

Note:

• If you don’t see the correct Wi-Fi network, make sure that the speaker is in range of the Wi-Fi router or access point.
• If your iPhone or iPad has never connected to this Wi-Fi network before, you will need to enter the Wi-Fi password at this time. Most users will not need to enter this password.
• If you cannot see your speaker under “SET UP NEW AIRPLAY SPEAKER...”, unplug and plug in power again to start it again.
• About streaming music from Apple TV, iTunes and Mac, you can visit https://support.apple.com/HT202809 for more information.

What you need first

• A Harman/Kardon Enchant Soundbar (1300 or 800 model).

• Latest version of the Google Home app
• A mobile device or tablet with Android or iOS system.
• An internet connection.
• Dual-band router with 2.4GHz and 5GHz connection

Adding your Enchant soundbar to your Wi-Fi

1. Open the Google Home app

      

2. Click on "ADD" to connect your Enchant 800 or Enchant 1300 Soundbar to your Wi-Fi network.
3. Follow the instructions on screen and enjoy beautiful sound using Chromecast technology.

Usually, the first time you connect the N90Q to your computer with the USB cable, and turn the headphone ON, it will cause a message to open on your computer, informing you that this new device has been connected, and a software package is being imported. Next time, you may get a warning that your USB device is not recognized by the computer, but that does not mean that the headphone will not work, it just means that you must activate it in the audio control systems. Locate the speaker symbol, which is usually shown at the extreme right in your computer taskbar along the bottom of the screen. Right-click on the speaker symbol. A menu opens, and you must highlight and click on Playback Devices. Now a small window opens, showing the Playback tab, with all available speaker option. One of the options should read something like this: " Speakers. AKG N90 headphones - Firmware version A2.12. Ready." Highlight this option, and then click the "Set Default" button that is now available in the window. Audio should immediately be sent to the N90 headphones as a digital signal, which is then converted and amplified inside the headphones. Now you can enjoy world-class music listening. If the computer will not show N90Q as an option, it is usually a solution to disconnect the headphone, then reconnect it. Sometimes this must be done two or three times before the computer "sees" the headphone.

(1) Use JBL One App to set up the My Moment Feature.
(2) Select the JBL device you want to set your favorite music to the My Moment feature.
(3) Tap the My Moment card to assign music.
(4) Click Add Music to manage music streaming services and specific music tracks.
(5) Set the timer to inactive speaker/soundbar (optional)
(6) Set the music loudness (optional)
(7) Press SAVE

If you encounter issues using the speaker with your phone or tablet, or you want to remove all previous Bluetooth pairings from the speaker, it may be necessary to 'factory reset' the speaker.

How to reset
First, remove or forget the speaker from the list of paired Bluetooth devices in the settings of the phone or tablet.
Then, with the speaker powered on, press and hold the Volume + and Play buttons simultaneously for 3 seconds until the unit turns off.
The speaker has now been restored to factory default settings. 

1. Power on the Enchant 800 or Enchant 1300 Soundbar. 2. In any source mode, press the power and source button for 5 seconds. 3. The Enchant 800 or Enchant 1300 will power off automatically and turn on again. 4. Your device is now reset back to default Factory settings. 5. You can now redo the setup through the Google Home app or pair with a new smartphone or tablet.

The reset for the Tuner 2 and Tuner XL is as follows:
Reset to factory default - Long press Preset 1 & Bluetooth buttons for more than 10 seconds.

If you wish to reset your speaker due to various reasons, then keep reading, and follow along. 1. Press and hold Volume+ & Play/pause buttons down at the same time for more than 5 seconds. 2. The Pulse 4 will turn off, indicating that you did a successful reset. 3. Switch your Pulse 4 on again. 4. Connect with your favorite Bluetooth device and enjoy the music! Do you still have problems? Contact our Customer Service for more help!

With our JBL BAR 5.1 Surround there is two types of resets, one is to reset the WiFi settings and last one is to restore factory default settings.

Let us walk through each one of them.

Resetting WiFi settings

1. Turn on your JBL BAR 5.1 Surround.
2. Press and hold POWER button down for more than 10 seconds.
3. All of your WiFi configuration is lost and you need to reinstall it again.

Use the Google Home app to install the device on your WiFi network.

Resetting to Factory default settings

1. Turn on your JBL BAR 5.1 Surround
2. Press and hold POWER and SOURCE button for 3 seconds.
3. Your device is now reset.

You can now start allover with installing your BAR 5.1 Surround.​​​​

With our JBL BAR 9.1 Surround there is two types of resets, one is to reset the WiFi settings and last one is to restore factory default settings. Let us walk through each one of them. Resetting WiFi settings Turn on your JBL BAR 9.1 Surround. Press and hold POWER button down for more than 10 seconds. All of your WiFi configuration is lost and you need to reinstall it again. Use the Google Home app to install the device on your WiFi network. Resetting to Factory default settings Turn on your JBL BAR 9.1 Surround Press and hold POWER and SOURCE button for 3 seconds. Your device is now reset. You can now start allover with installing your BAR 9.1 Surround.

The factory reset button restores your device to the default settings, including network and audio configurations. 

Please use one of the following solutions:

1.  Press and hold VOL -, VOL +, and Source buttons on the device at the same time until the LED light flashes (hold for more than 5 seconds)

Or alternatively;

2. Open your JBL ONE App.
3. Navigate to the support tile.
4. Select RESTORE FACTORY SETTINGS. 

To reset your JBL Bar 2.0 or 2.1 back to factory default settings, follow the steps below.

1. Turn on your JBL Bar 2.0 or 2.1
2. Press SOURCE and POWER buttons on top of the bar at the same time for more than 3 seconds.
3. Your soundbar will now power off and on again.

All Bluetooth paired devices are now removed from the internal memory; please Bluetooth pair your devices again.

Resetting the device

1. In any source mode, press and hold the power button and Source button for 5 seconds.
2. When the factory settings restore is complete, the soundbar automatically turns off and restarts.
3. You can now set it up via Google Home app again or connect any new Bluetooth devices.

On the bottom of your ADAPT+ there is a reset button. Hold it down for 5 seconds, until the round button LED lights up in white. The product is now reset and ready to be set up again.

In order to reset the headphones: 

Long Press of volume + and volume - at the same time while the unit is on. Make sure that bluetooth is NOT on and connected to any device. 
When reseting, LED will blink faster. 

Press and hold the 'DAB/FM' & 'Preset 1' buttons for more than 2 seconds. The Horizon 2 is now reset to the default factory settings.

Resetting the Partybox to Factory Settings

1. Press and hold "Play/Pause" and "Volume +" down for > 10 seconds.
2. The JBL Partybox will power off and back on and is now reset.