How To
How To
1674 results
-
When the earbuds are connected to the USB wireless dongle and Bluetooth connection at the same time, triple tab on the left earbud to switch between the two connections. You'll hear a tone after you triple tab the left earbud signaling the switching is in progress. If you receive an incoming call from your mobile device, you can double tap either earbud and the earbuds will automatically switch over to that connection while answering the call.Was this helpful? Thank you for your feedback!
-
Onboard Adaptive Noise Cancellation is controlled by the multi-function button on the rear of the left ear-cup. The feature is switched on by default, but you can SHORT press the multi function button to toggle from ANC to talk-through. Turn off ANC by long-pressing the multi-function button.Was this helpful? Thank you for your feedback!
-
Onboard Adaptive Noise Cancellation is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SHORT press the multi-function button to toggle from ANC to talk-through. Turn off ANC by long-pressing the multi-function button.Was this helpful? Thank you for your feedback!
-
Download and connect the Onyx Studio 9 with the Harman Kardon One app. Select the product in the app and go to [Product information] and then select [Product Software]. If a new update is available, you can select [Update].
Was this helpful? Thank you for your feedback! -
To choose a wireless network for your BDS system, please do the following. 1: Select Choose a network from the Setup Wi-Fi list. 2: Follow the instructions on the screen to select your wireless home network and enter your security password, if applicable.Was this helpful? Thank you for your feedback!
-
By pressing and holding the "Volume+" and "Bluetooth" button together for 5 seconds. A voice will say the version number.Was this helpful? Thank you for your feedback!
-
The red charge light turns off when charging has finished.Was this helpful? Thank you for your feedback!
-
When the Xtreme is ON, the row of 5 diodes at the bottom of the front will light up in turn, with the top flashing LED showing how far charging has progressed. When full charge has been reached, all diodes light constantly. In some cases, the fifth diode keeps on blinking, but does not light up constantly, no matter how long charging continues. Sometimes it will show constant light after charging has been stopped. This is normal, caused by tolerances in the circuits, and is no cause for alarm. The battery is charged to the same level. If the Xtreme is OFF, no diodes will light when full charge has been reached.Was this helpful? Thank you for your feedback!
-
The charging LED stops lighting white, and goes dark.Was this helpful? Thank you for your feedback!
-
The red diode that lights up when charging begins will go out again when charging is complete.Was this helpful? Thank you for your feedback!
-
With the Onyx Studio 2 switched ON, the ON/OFF switch light flashes while the unit is charging. If the unit is switched OFF, no indication shows that charging is taking place, but charging still takes place. When charging is complete, the light becomes constant. There is no battery status indication, so it is not possible to follow the power level of the battery.Was this helpful? Thank you for your feedback!
-
Press and hold the Source, Vol+ and Vol- buttons at the same time until you see the text "reset" on the soundbar's display.Was this helpful? Thank you for your feedback!
-
Press volume + and volume - simultaneously for 5 seconds to reset.
The headphone must be ON while doing this.Was this helpful? Thank you for your feedback! -
On the back of your OMNI BAR+ there is a reset button. Hold it down for 5 seconds, until the round button LED lights up in white. The product is now reset and ready to be set up again.Was this helpful? Thank you for your feedback!
-
The reset procedure is quite different from the rest of the OMNI+ series. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.Was this helpful? Thank you for your feedback!
-
There is a reset button on the bottom of the Omni+ devices. Press and hold this button for 5 seconds to perform a factory reset of your product. All product settings, Wi-Fi, and Bluetooth connections will be erased. To reset the OMNI 50+ speaker, please do the following: First, press & hold ‘Source’, ‘Vol+’, ‘Vol-‘ buttons at the same time. The Omni 50+ will switched off, indicating that the product was successful reset. Secondly, press ‘power' button to turn on power for the Omni 50+ speaker. Now you can easily set up the product again for your home Wi-Fi network.Was this helpful? Thank you for your feedback!
-
To reset your JBL Tuner simply Long press Volume+ and Bluetooth button for 5-7 seconds. Your Tuner is now successfully reset and you can Bluetooth pair with it again.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks two colors, and now you have reset to factory settings.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks slowly for about two seconds, and now you have reset to factory settings.Was this helpful? Thank you for your feedback!
-
You can reset the E25BT in two ways: 1: Press and hold Volume + and Volume - simultaneously for more than 3 seconds. This resets to factory settings, clearing the pairing list. 2: With unit in ON mode, plug in the USB cable. This resets the unit and puts it into charging mode.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks slowly for about two seconds, and now you have reset to factory settings.Was this helpful? Thank you for your feedback!
-
On the soundbar, press and hold the power and source button for more than
10 seconds.
Please note this procedure will revert ALL settings back to factory default.Was this helpful? Thank you for your feedback! -
Press and hold the "Microphone off" button for 5 seconds. The Allure speaker will tell you when it is ready to be configured.Was this helpful? Thank you for your feedback!
-
To prevent other people from changing the source on your BDS through Bluetooth, you can disable the “Automatic Playback” function in the System Settings of the BDS ( 280, 580, 280S and 580S ). This does not prevent others from connecting to one of the two Bluetooth receivers in the BDS units, but it prevents other people from “interrupting” your playback source. This is where the change is done: Settings – System Settings Automatic Playback ( Enable/Disable ) Enabled: People can connect to your BDS and start playing music/audio. Your BDS will automatically change source ( or switch on, when BDS is in Standby mode ) from any source. Disabled: People can connect to your BDS, but the BDS will not automatically change source, or go out of Standby mode when a music/audio signal is sent through Bluetooth.Was this helpful? Thank you for your feedback!
-
To play the surround sound with DOLBY ATMOS or DTS:X, connect your Blu-ray player or other digital device to the HDMI input connector on the soundbar. If the TV support Dolby ATMOS, served over HDMI ARC, just make sure it is selected in the TV setting menu. To select the most suitable amount of sound effect of DOLBY ATMOS and DTS:X, press on the remote control ATMOS level button, to switch between MID, HIGH, LOW or OFF. Note: If your TV has an eARC HDMI input, you can connect your Blu-ray player or other digital device to the HDMI IN connector on the TV.Was this helpful? Thank you for your feedback!
-
On the back of the SB150 subwoofer, you will find a "pair" button. Hold down the pair button for 3 seconds. It will start flashing amber rapidly, indicating that the pairing mode has begun. You don't need to press other buttons to make a connection, once the amber light is steady, it is connected to your SB150 soundbar.Was this helpful? Thank you for your feedback!
-
We have some suggestions if you want to enjoy the best performance from your Bluetooth devices. 1. Please note that if you have a large number of Apps open in your smartphone or tablet, this may block or overtax its processor. Dropouts may result. Try to close all or most active apps. This should solve the problem. 2. Bluetooth signals from smartphones and tablets are not very strong. Make sure that the signal does not have to pass through doors, walls etc. Always maintain a clear line of sight between transmitter and receiver. 3. Do not carry your smartphone in your pocket, if you have dropouts. Your body can act as a screen, reducing the strength of the Bluetooth signal. Put the phone on a table or other surface. 4. Do not walk around while listening. If the transmitter and the receiver are moved in relation to each other, dropouts occur more frequently. 5. Under normal circumstances, you can expect a range of 5 meters with no problems, if you follow the above advice. In some instances range is longer, but we cannot promise this.Was this helpful? Thank you for your feedback!
-
That is easy, simply say "Alexa, mute" or "Alexa, mute music". To resume playback if needed, say "Alexa, resume playback".Was this helpful? Thank you for your feedback!
-
If you are not using the microphone, make sure that any communication software such as Zoom, Skype, Discord, etc. are closed and that your microphone is muted. You can also take advantage of it's Dual Connect feature and place one of the earbuds in the charging case and speed charge the earbuds to extend the playback time.Was this helpful? Thank you for your feedback!
-
Unfortunately, the JBL AmpUp App is no longer available for download.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00
