To have the best possible performance for OMNI+ system we advise to have a dual-band router with a powerful chipset and ram for best Wi-Fi performance. This will not only help our products to perform better and more stable, but your other devices at home will have more power and fewer interruptions. Please also be sure that your home Wi-Fi router has Multicast enabled, as our Omni+ system requires this feature enabled in order to work (same goes for Chromecast devices). Always connect our Omni+ system to 5 GHz Wi-Fi whenever possible to limit the risk of devices being slow or interrupted on 2.4GHz Wi-Fi.

Different games have different settings, but as a general rule, make sure that your game outputs multi-channel unprocessed audio. We recommend 7.1 surround, but 5.1 works too. Always disable any other processing (like DTS and Dolby).  

If you are having trouble with distortion or drop outs, try the following suggestions: 1. Move the audio source closer to the speakers. 2. Move the speakers closer to each other. 3. Make sure only one of the two speakers are connected to the audio source. If both are connected to the audio source, disconnect the connection between the audio source and the second speaker. 4. Make sure the audio source connects with one streaming speaker only, disconnect other Bluetooth connection. 5. Restart both your speakers and the audio source. 6. Make sure the environment is not congested by other wireless signals.

The first thing you’ll notice is that sound no longer feels like it’s “inside your head.” Suddenly it seems like the game audio is coming from high-quality loudspeakers—or the virtual game world—all around you.

It’s a different experience than you get with other headphones, and may take a little while to adjust to. For example, sounds coming from sources in the distance will seem farther away, as they would in real life. Even though you might be used to those sounds feeling closer with other headphones, JBL QuantumSURROUND provides hyper-accurate spatialization that can give you a competitive edge.

So spend some time dialing in the EQ to your liking, and see how real-world hearing helps you pinpoint enemies and bring the game to life. 
 

If your teammates can not hear you, make sure of the following:

USB is correctly plugged in
Only one voice chat application is in use while in-game.
The mic input is set to JBL Quantum Stream.
Mic gain is not turned all the way down
Mic is not muted (mute/unmute by pressing the touch panel on top of the mic). By default the RBG will indicate red for muted, and green for unmuted(active).

 

To have the best Active Noise Canceling performance possible, we advise you to keep the earbuds clean as much as possible. In case the IR sensors are covered with dirt of any kind, the Active Noise Cancellation performance will not be as effective. Sometimes, it may not give you the desire outcome to enjoy your music. 

Let's run through some basic check marks to ensure we didn't miss anything while setting up your device.

1. Your Citation device is turned on
2. Check the password you have entered, and re-enter it again (typos can happen).
3. Make sure your mobile device has the initial support needed:
   1. Android 4.4 OS and higher
   2. Apple iOS 10 OS and higher
   3. The latest version of Google Home app
4. Your phone needs Bluetooth to be on 
5. Enable Location Service (Android only)
6. Plus you need to permit Google Home app to access your location on the phone (Android only).

The basic check is done, and we are now moving into your Wireless network setup.

1. Try moving your speaker closer to the Wireless network router 
2. Have you previously connected the speaker to your WiFi network?  If yes, look below or move to "Troubleshooting"
   1. Did you recently make any changes to your network, such as buying a new router, adding an extender, or maybe changed settings?

   2. Maybe your ISP (Internet Service Provider) did some changes, possibly even updating your Wireless router software.

If you still are experiencing issues connecting the device to your Wireless network, let's do some further troubleshooting.

Troubleshooting

1. Your WiFi router might need a reboot, unplug power for 1 minute and connect power again.
   1. While you are rebooting your WiFi router, we advise doing the same for your speaker. Simply disconnect power and reconnect power again.
   2. In case rebooting the speaker didn't work, let's try resetting your speaker by pressing the Reset Button for 5 seconds (Front LED will light up).
2. Go ahead with the setup again (remember to open Google Home app )
3. Reboot your mobile device

WiFi Network Troubleshooting

• Check your WiFi router settings. Be sure that UPnP (Universal Plug and Play) is enabled.
• Change Wireless channels on your WiFi router on 2.4G or 5G..
  • Avoid using other channels on 2.4G other than 1, 6 and 11. The rest are a NO-GO.
  • Keep a maximum of 8 devices in total on 2.4G (that is including our speakers).
  • Move products to WiFi 5G band, if they support it, to reduce the stress factor on the 2.4G band
• Check your WiFi router to see if there is a MAC address limitation.
  • MAC address limitation is when your router is set/fixed to a maximum of 20 devices (or whatever it may have been configured for).
  • When you want to add the 21st device your router will deny access because you have filled up the 20 devices.
  • You need to clear or delete old devices that are not in use anymore. This may require someone with technical knowledge.
  • We advise that you don't have any MAC address limitations at all.
• Avoid bad extenders (Cheap ones are often not powerful enough to deal with or handle the kind of data required to transmit high quality audio).
  • With extenders, the connection between "router and extender" is decreased by 50%.  That said, your data will be even slower,. having to processes it while the speed is decreased.

There are more things you can do to optimize your WiFi router, but these above are the most common issues happening in users homes.

 

Normally, the InfinityLab power bank may be warm to the touch during discharging.  
However, if the power bank becomes too hot, starts to expand, or emits a strong odor, please stop using it immediately and contact our customer service. 

The connector between headphones and cable is Mini-XLR with lock mechanism. The connector that goes into sources is a combination plug, 3.5mm jack with 6.3mm adapter.

Normal: Trigger output is a standard 12VDC signal. Pulsed: Trigger output in a 12V pulse 50-100ms wide. Theatre: Turns the trigger on (standard 12VDC) only if the current input is in SSP mode, otherwise the trigger is off.

Citation speakers support 802.11g, 802.11n, and 802.11ac standards on both 2.4 GHz and 5 GHz bands. We recommend using 5 GHz if available, as this will give you more stable performance and use the full power of your wireless audio. Contact our customer support to get in touch with an expert that can help you with your Wi-Fi network. We are here to help!

10 minutes before the time limit has been reached, a voice prompt will be played on the headphones. When reaching the time limit, the volume will be muted, and a new voice prompt will inform that the listening limit has been reached.

Getting started with the checklist

• A JBL LINK device(s).
• Latest version of the Google Home app installed on your mobile device.
• Latest version of the Google app  (Android only) installed on your mobile device.
• A Google Account (you can create one online via Google).
• A mobile device with either iOS or Android support.
  • ​Must have iOS 10 or higher
  • Must have Android 5.0 and higher
  • There is no support for PC set up.
• An internet connection from your local ISP (Internet Service Provider).
• Your Wireless Network must secured with WPA2 Encryption (Enterprise mode NOT supported). 
• Availability and performance of certain features, services and applications are device- and network-dependent and may not be available in all areas; subscription(s) may be required, and additional terms, conditions and/or charges may apply.

Wi-Fi requirement

• Wi-Fi routers must have Encryption enabled to install JBL LINK speakers (WPA2 etc).
• Wi-Fi Extenders need to feature support of Multicast forwarding and UPnP.
• Always use 5 GHz Wi-Fi for best performance and less interference.
• For routers that have 2.4G Wi-Fi support only, make sure that they are using channels 1, 6 or 11 only.

You can now install your JBL LINK speaker to your Wireless Network and you can find our setup article that shows how to install your LINK product.

 

JBL QuantumSPHERE 360 is JBL QuantumSURROUND that’s kicked up a notch by using a head-tracking sensor to fix sounds in 360 degrees of space around you. With typical headphones, when you move your head, the soundscape follows your movement. But with JBL QuantumSPHERE 360, if you rotate your head, the sound source’s perceived location stays in place because the head-tracking sensor compensates for your head movement. For example, if there’s a sound coming from in front of you, and you turn your head to the left, the sound source’s perceived location moves to your right ear—the sound stays locked in space as you move your head. 

Also, the human brain uses small head movements to distinguish if sound sources are behind or in front of us. The brain processes the differences between when a sound arrives at the left vs. the right ear to determine where the sound is located. So with JBL QuantumSPHERE 360, you can move your head naturally to pinpoint the exact source of sounds around you. 

The Normal and Pulsed DC triggers are active (on) when the No. 523 and No. 526 is on, they are not active (off) when the No. 523 and No. 526 is off. The Theatre DC trigger is present only if the current input is in SSP mode, otherwise this trigger is off.

First try using a different flash drive, we recommend the following: ScanDisk PNY Kingston Verbatim If the problem persists try using an updated version of Winzip when downloading the zip file to the USB flash drive.

Yes, when changing volume to higher or lower, the LED will illuminate to show that you are changing the volume.

When the speaker is switching quickly between music sources via Bluetooth, it's normal to experience a very short 'pop' sound because the Bluetooth signal is breaking in and doing the handshake with the speaker. It won't appear after the Bluetooth signal is stable.

Please note that the LFE Trim function is only active with surround source signals that feature a separate LFE track for the subwoofer. It does not affect subwoofer level when playing stereo or mono.

This problem is usually caused by pressing down too hard on the soundbar's VOL + or VOL - Buttons. Only press just enough for one click to be felt. If a second click is felt in the button, you are pressing too hard, and you are actually activating the MUTE function for learning, not VOL up or down. You may have to repeatedly let go of the VOL button on the soundbar, followed by pressing it again and then pressing the VOL button on the TV remote before the surround light on the soundbar lights up white and goes back to amber flashing, as a sign that this function has been learned. This is no problem, though. Just keep trying until the three commands have been learned. The soundbar only exits learning mode when you press and hold the surround button as the final step.

• Please check whether your head unit Bluetooth support EDR (Enhanced Data Rate) • If the head unit does not support EDR this will cause the transfer data rate to be low and will impact the audio quality.

The PartyBoost feature is not available when your JBL speaker is connected to a computer via Bluetooth. This is a technical limitation. When connected to a computer, the computer is acting as the primary device. Therefore, the JBL speaker does not have control of re-transmitting the Bluetooth signal to other JBL speakers.

NOTE: Speakers effected by this are the JBL Flip 5, JBL Flip 6, JBL Charge 5, JBL Pulse 4, JBL Xtreme 3, and JBL Boombox 2, as well as future products featuring the PartyBoost feature.

The rechargeable AAA cells may of course be worn out, or they may not be installed at all. If this is the case, either insert the cells, or you can order new cells as original spare parts. Please contact Harman Helpdesk for your country, or the distributor for your country, for further info about how to buy new cells. Please note that the cells MUST be compatible with charging contact for the minus pole located on the side of the cell. Normal cells will not work. This is clearly mentioned in the owner's manual, and shown with a drawing. If you have purchased new cells with plastic coating along the length of the cell, it may be possible to peel off the coating by cutting gently with a knife, then peeling it off. Only about 1 cm needs to be open to the metal, closest to the flat end, for contact to be possible. Please note that the ear pads on K 912 are removed by simply grabbing the plastic plate that holds the ear pad, and pulling it away from the ear pod. There is one battery in each ear pod. For K 915, never just pull the pad away, since the locking claws are released by being rotated away from their locked position.. Both batteries are under the right-hand pad, and there is a silk-screened instruction on the top of the pod, showing that you must rotate the pad plate just a few mm counter-clockwise to unlock it.

The wireless charge receiver in the smartphone may not be adequately coupled to the wireless charging transmitter on Smartbase. Re-adjust your smart phone’s position on the wireless charge arm.

To set up the Harman Kardon Adapt in the HK Controller app, you have to select "One speaker", not the Adapt+ option. When selecting "One speaker", simply follow the on-screen instructions to install your Adapt on the Wi-Fi network. Note that the instructions for Adapt devices will appear on your screen after 30-45 seconds (Only Apple devices).

Yes it will.

Please check the picture settings on your cable box, particularly the aspect ratio settings, which will vary depending on the brand and model of your cable box and on your local cable provider. You may wish to consult with your cable provider for more information on how to adjust the cable box's settings. Some settings, such as a setting to force an analog channel's native 4:3 aspect ratio to 16:9 widescreen to fit your display, may interfere with the cable system's copy-protection feature and cause distortion.

This is caused by the volume synchronizaton system in the iPad. When you switch off the iPad with click sounds activated, it sends the click sound to the Go+Play, also ordering the Go+Play to increase volume to maximum. The hiss is a result of the Go+Play Wireless being at full volume. As soon as you re-start your music playing from the iPad, volume is back to normal music use. If you do not switch the iPad on again, the Go+Play goes into standby after a few minutes, and the hiss disappears. You can prevent this problem by de-activating the click/alarm sounds on the iPad.

Some vehicles don’t provide an isolated ground for the head unit which may introduce noise. Please connect your smartphone to JBL DRG and enable the “Aux Noise Cancel” button in the App. This can be found right after Aux Line option in Connection Mode section.

Some head units in the vehicles use isolated grand, if JBL DRG use isolated grand as well, this will disable the chips inside DRG. Please connect your smartphone with JBL DRG and disable the “Aux Noise Cancel” button in the Apps right after Aux Line option in Connection Mode section.