How To
How To
1640 results
-
The lights cannot be adjusted by user. The digital front panel display has automatic light intensity adjustment, which follows the level of light in the room.Was this helpful? Thank you for your feedback!
-
Yes, in the Harman Kardon Remote APP, it is possible to change the AURA's Bluetooth name.Was this helpful? Thank you for your feedback!
-
Yes, on your computer, enter the IP address of the receiver in the internet browser. In the page that opens, it is possible to change the name.Was this helpful? Thank you for your feedback!
-
Yes, when the Esquire 2 is switched ON, it can charge a smartphone or tablet (or other USB-chargeable device that matches) through the special USB port. This function is available both when Esquire 2 is running on battery, and when connected to a charging port itself.Was this helpful? Thank you for your feedback!
-
It is not possible to clean the clear dome of the AURA. The dome cannot be removed without damaging the product. The only solution if debris falls into the AURA is to try to shake it out through the bass tube. We cannot recommend using a vacuum cleaner to suck or blow through the bass tube.Was this helpful? Thank you for your feedback!
-
The JBL Bar 300 does not support a subwoofer. Alternatively the JBL Bar 500 has a wireless subwoofer included.Was this helpful? Thank you for your feedback!
-
No, it only supports one Bluetooth connection. Simply disconnect the paired phone/tablet from your Bluetooth device settings, then hold down the Bluetooth button for 3 seconds, and then you are able to pair with the new smartphone/tablet.Was this helpful? Thank you for your feedback!
-
The JBL Bar 500 does not support rear/surround speakers. Alternatively the JBL Bar 800/1000 has detachable wireless rear speakers included.Was this helpful? Thank you for your feedback!
-
Yes, you can control the No. 585 over port 7701, providing the control is set for Ethernet in the menu. The commands are the same as RS232 and you connect to it by telnet on port 7701 of the IP Address of the unit. Note there is no echo of the command when you type and it answers with a copy of the command and OK if it accepted the command and EH? if it did not.Was this helpful? Thank you for your feedback!
-
The SB20 supports these programmable IR codes for your TV remote: Volume+, Volume-, Mute and Power commands.Was this helpful? Thank you for your feedback!
-
Yes, but only via cable, and noise cancelling cannot be activated meanwhile. Since the charging socket is located on top of the ear pod, adjustment is limited in that direction while the micro-USB plug is inserted.Was this helpful? Thank you for your feedback!
-
No, the noise cancelling function is always active when Bluetooth is on. If you want to listen to music without NC on, you must use the cabled audio connection.Was this helpful? Thank you for your feedback!
-
Yes, charging and listening simultaneously is possible. With N90Q, charging takes place at all times when listening to digital audio from a USB socket.Was this helpful? Thank you for your feedback!
-
No, in order to go through the setup procedure, it is necessary to activate the (OSD) On-Screen-Display, and this is not possible on the front panel buttons, you need the remote control. Only the remote control features the necessary OSD button.Was this helpful? Thank you for your feedback!
-
Yes, the Harman Kardon SB20 features IR learning functionality. Please follow these steps: Step 1: Power on your Harman Kardon SB20. Step 2: Press and hold the SB20 surround button for 5 seconds. This will make the system enter IR learning mode. The power button will flash amber while in learning mode. Step 3: Now the SB20 can learn to respond to your TV remote control. These commands can be learned: To learn the SB 20 VOL+ command, press volume + on the SB 20 top panel, then press VOL+ on your TV remote control. The power button should blink amber, and the surround button will light up for 1 second. This will indicate that the process was successful. Repeat the procedure for volume-, mute and power on/off. Step 4: To exit the learning mode, press and hold the surround button for 5 seconds again. The power button light goes out.Was this helpful? Thank you for your feedback!
-
Yes, they are quite easy to remove, and with a little care, new ear pads can be fitted in one or two minutes. You can do this yourself.Was this helpful? Thank you for your feedback!
-
Yes, press Volume + and Surround button at the same time for 5 seconds.Was this helpful? Thank you for your feedback!
-
Yes, this can be done very easily by doing the following procedure: 1: Power on the Cinema Base. 2: Simultaneously press the “Surround” and “VOL –” buttons (at the same time). 3: The Cinema Base source LED button will light amber in color, for 1 second, then the power button LED light will go off and on. 4: Your Cinema Base is now reset.Was this helpful? Thank you for your feedback!
-
Yes, by holding down Volume+ and surround button for more than 5 seconds will reset the SB20. The SB20 will automatically reboot itself, after it has been reset.Was this helpful? Thank you for your feedback!
-
Yes, switch the soundbar ON, then press the volume - ( minus ) and surround buttons at the same time for 5 seconds. Now the device is reset.Was this helpful? Thank you for your feedback!
-
The JBL Cinema SB450 can be reset to its default factory settings and erasing all programming. To reset the soundbar, press and hold Volume+ and Virtual Surround buttons for 5s.Was this helpful? Thank you for your feedback!
-
No, NC is always on when Bluetooth is on. However, it is possible to select NC on or off when listening via cable.Was this helpful? Thank you for your feedback!
-
No. There is no way to turn off the blue LED light from our wireless headphones unless they are turned off.Was this helpful? Thank you for your feedback!
-
Yes, Alexa has various voice commands to turn up the volume. Try saying "Alexa, turn it up" or "Alexa, set volume to 5".Was this helpful? Thank you for your feedback!
-
If any update exist, then it is only possible to get it updated, via our authorized service center. The USB port on the back, is meant for service use only. Contact support for more information.Was this helpful? Thank you for your feedback!
-
While this is indeed possible, no such cable is made by AKG, so only cables from third-party manufacturers may be considered. Please note that internal pin configuration must be identical to the original cable for such a cable to work with the headphones.Was this helpful? Thank you for your feedback!
-
No, this is not possible. Even though the MMCX (micro-miniature coaxial) connectors seem identical, they are not the same dimensions.Was this helpful? Thank you for your feedback!
-
Yes, two headsets can be used simultaneously with one transmitter.Was this helpful? Thank you for your feedback!
-
Our BDS system does supports WPS PIN, please do the following: 1. Select WPS PIN from the Setup Wi-Fi list. A PIN code is displayed on the screen. 2: Enter this same PIN on your wireless router’s internal web page to connect. See your router’s user manual for more details.Was this helpful? Thank you for your feedback!
-
For your personal safety and to avoid possible damage to your equipment and speakers, it is always a good practice to turn off and unplug the AVR and ALL source equipment from the AC output before making any audio or video system connections.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00
