JBL PartyBox 100
Bærbar Bluetooth party-højttaler med lyseffekter
Sold from 2019 until now
Getting started with your JBL PartyBox 100
Documents & Downloads
Specifications
- Udgangseffekt (W)
- 160
- Dynamisk frekvensområde (Hz)
- 45Hz-18kHz
- Mål (cm)
- 28.8 x 55.1 x 29
- Mål (inch)
- 11.3 x 21.7 x 11.4
- Vægt (kg)
- 9.7
- Vægt (lbs)
- 21.4
- Bluetooth-version
- 4.2
- Batterikapacitet (mAh)
- 2500
- Ladetid (timer)
- 6.5
- Spilletid (timer)
- 12
- 3,5 mm lydindgang
- Ja
- Bluetooth
- Ja
- Charging cable
- Ja
- Lysshow
- Ja
- Wireless
- Ja
- Den berømte JBL-lyd
- Ja
- Genopladeligt batteri
- Ja
- Note
- The product is in compliance with the European Union energy legislation. 1) Bluetooth connection mode - The product is intended to be used for streaming music via Bluetooth connection. A consumer can stream Bluetooth audio to the speaker. When the product is connected through Bluetooth, the Bluetooth connection must remain active at all times to ensure proper operation. The product will enter into sleep mode (networked standby), after 20 minutes without operation, the power consumption @ sleep is less than 2.0 Watts, after which it can be re-activated via Bluetooth connection. 2) Bluetooth disconnection mode - The product will enter into standby mode, after 20 minutes without operation, the power consumption @ standby is less than 0.5 Watts.
Spil højt, stå frem - og vær klar til fest!
Flyt festen med kraften fra den bærbare JBL PartyBox 100. Lys natten op. Vælg det perfekte lysshow, eller lad musikken vælge stemningen. Skab dit eget mix. Vælg en playliste fra dit USB-stik, eller afspil trådløst fra en Bluetooth-kompatibel enhed. Lav dit eget rockshow med mikrofon- og guitarindgange. Find din perfekte lyd. Sæt din højttaler på et stativ, og fyld hele rummet med den dynamiske JBL-lyd. Fest hele natten med op til 12 timers batteritid. Sæt højttaleren til stikkontakten, så musikken aldrig stopper.
FAQs & How-Tos
-
If the buttons on your portable speaker are not working properly or are unresponsive while plugged into a power source, please try running the speaker on battery. If the buttons perform correctly while running on battery, this means your power supply is not providing enough current/amps. Be sure to use a power supply that has a rating equal to or greater than the amperage rating indicated in your product specs.Was this helpful? Thank you for your feedback!
-
You can use the PartyLight Sticks and the PartyLight Beam with older PartyBox speakers. The built-in sound detection algorithm sync the light with the music from the speaker.
The light also works if you don't own a PartyBox speaker as a built-in mic with a music detection algorithm automatically finds and syncs to any music device that's playing.
Was this helpful? Thank you for your feedback! -
It is very simple to connect to your Car with the JBL Partybox 200 or 300. Use the included cable that connects through the cigarette connector in your Car and power on the Partybox! Please note that the 12V connection does not charge the battery in the Partybox 300 - it will only power the Partybox when in use. To charge the battery, it will have to be plugged into AC power ( 110 - 230V )Was this helpful? Thank you for your feedback!
-
This product does not feature speakerphone or voice assistant functionality as it does not have a microphone.Was this helpful? Thank you for your feedback!
-
Demo mode
- Press the Play and Boost button at the same time for 5 seconds.
- Depending on what state your JBL Partybox is in, either you enter Demo mode or disabling it.
- NOTE: In Demo mode, you cannot use the JBL Partybox as most features and buttons are not working.
Was this helpful? Thank you for your feedback! -
Bluetooth Pairing
- Press the button on the Partybox to start the pairing process.
- Grab your device.
- Go to settings --> Bluetooth --> Enable Bluetooth -->
- Find the Partybox speaker you want to establish a Bluetooth connection to.
- You now have a successful connection and can stream your favorite music.
- NOTE: It is only possible to have two devices connected at the same time and if you want to listen through the second Bluetooth device then stop the current one from playing and use the second device.
- To stop Bluetooth broadcasting then insert a USB device.
Was this helpful? Thank you for your feedback! -
Finding the software version
- Press and hold the 'Volume-' and 'Bass Boost' buttons for 5 seconds.
- A voice will start prompting numbers which indicates the current software version.
Was this helpful? Thank you for your feedback! -
USB Stick
- Get an empty stick with speed of 2.0.
- Make sure it is formatted with FAT16 or FAT32.
- Your Music files can only be: (32-320kbit/s), (32-320kbit/s) and (44.1K/48K/192K).
- The Partybox supports up to 8 subfolders.
- It will be played in alphabetic sequence with main folders first then subfolders.
- To skip songs forward, double press the Play/Pause button. To skip back, triple press the Play/Pause button.
Was this helpful? Thank you for your feedback! -
Resetting the Partybox to Factory Settings
- Press and hold "Play/Pause" and "Volume +" down for > 10 seconds.
- The JBL Partybox will power off and back on and is now reset.
Was this helpful? Thank you for your feedback! -
This model is not supported by the JBL Partybox App.Was this helpful? Thank you for your feedback!
Images & Videos
Can’t find what you’re looking for?
Call us
Call us now at:
+45 32712498
Monday - Friday: 09.00-17.00
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00