Descripción general de la asistencia / Audio en Casa / Receptores - Digital / Receptores - Tubo / AVR 430

AVR 430

Audio/Video Receiver With Dolby Digital & DTS (80 watts x 2 | 65 watts x 5)

Vendido desde 2003 hasta 2004

Producto predecesor:	AVR 525
Producto sucesor:	AVR 435
Hecho en:	China

Documentos y descargas

Guía de inicio rápido

Quick Start Guide (English) 369.05 KB

Especificaciones del producto

Características generales

Power Requirements: AC 120V/60Hz

Power Consumption: 59W idle, 940W @ rated power output (7 channels driven)

Digital Inputs (coaxial/optical): 2/2 on Rear; 1/1 on front

Analog Inputs: 1 A/V on front panel (switchable to output)

Analog Inputs: 2 audio-only

Analog Inputs: 4 A/V on rear panel

Analog Inputs: 6-/8-channel input

Analog Inputs: tuner

On-Screen Display: Yes

Multizone Capability: Audio; A-BUS Ready; RS-232 serial control port; surround back channels assignable to remote zone; Zone II remote

EzSet: Yes

Remote Control: Backlit, eight-device, programmable learning remote (2-line LCD display)

Shipping Weight (System, Accessories, Packing): 45 lb (20.4kg)

MSRP U.S.: $999.95 each

Características Audio

# of Amplifier Channels: 7

Stereo Mode:

Continuous Average Power (FTC) per Channel: 80 Watts per channel, 20Hz – 20kHz, @ <0.07% THD, both channels driven into 8 ohms

Front L & R Channels: 65 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms

Center Channel: 65 Watts @ <0.07% THD, 20Hz – 20kHz into 8 ohms

Surround Channels (L & R Side, L & R Back): 65 Watts per channel @ <0.07% THD, 20Hz – 20kHz into 8 ohms

Input Level/Impedance: 200mV/47k ohms - Linear (High-Level)

Signal-to-Noise Ratio: 95dB (IHF-A)

Surround System Adjacent Channel Separation:

Dolby Pro Logic I and II: 40dB

Dolby Digital: 55dB

DTS: 55dB

Frequency Response: 10Hz – 130kHz (+0/-3dB @ 1 watt)

Transient Intermodulation Distortion (TIM): Unmeasurable

Slew Rate: 40V/µsec

Medidas

Width: 17.3 inches (440mm)

Height: 6.5 inches (165mm)

Depth: 17.1 inches (435mm)

Weight: 39 lb (17.7kg)

Dimensions:

Carton Dimensions: 20.1 inches x 10 inches x 22.2 inches (510mm x 254mm x 565mm)

Especificaciones de vídeo

Television Format: NTSC

Input Level/Impedance: 1Vp-p/75 ohms

Output Level/Impedance: 1V/75 ohms

Video Frequency Response:

Composite and S-Video: 10Hz–8MHz (–3dB)

Component Video: 10Hz–50MHz (–3dB)

Tuner Specifications

Frequency Range: AM... 520–1720kHz

Frequency Range: FM... 87.5–108.0MHz

Signal-to-Noise Ratio: AM... 45dB

Usable Sensitivity: FM... IHF 1.3µV/13.2dBf

Signal-to-Noise Ratio: FM... Mono/Stereo 70/68dB

Usable Sensitivity: AM... Loop 500µV

Distortion: AM... 1kHz, 50% Mod 0.8%

Distortion: FM... Mono/Stereo 0.2/0.3%

Selectivity: AM... ± 10kHz, 30dB

Stereo Separation: FM... 40dB @ 1kHz

Selectivity: FM... ± 400kHz, 70dB

Image Rejection: FM... 80dB

IF Rejection: FM... 90dB

Amplifier Specifications

Amplifier Power (RMS): 65 x 7 @ 8 ohms, (20Hz – 20kHz, <0.07% THD) (all channels driven at full power)

High Instantaneous Current Capability (HCC): ± 40 Amps

The truth is in the numbers: a 32-bit post processor, RS-232 connectivity, a two-line LCD remote control, Logic 7, Dolby Pro Logic II, DTS 96/24, a quadruple crossover with six crossover points per speaker location and more multiroom options than any other receiver, including A-BUS Ready connectivity. The AVR 430 is Harman Kardon to the core. You can count on big numbers from the seven-channel, high-current, ultrawide-bandwidth amplifier, along with the ability to assign two of the channels to a second remote zone. No matter how you add it up, the AVR 430 delivers high performance.