How To
How To
1674 results
-
If your volume level is quiet, make sure that the TalkThru is not activated on your headphones. In order to deactivate or activate TalkThru, quickly press the ANC button located at the top of the LEFT ear cup. You will hear an audible voice stating, TalkThru On when activated, and 'ANC On' when deactivated.Was this helpful? Thank you for your feedback!
-
When you press the power button you will hear a “door locked” tone. This means the top capacitive touch buttons have been locked. At this point you cannot trigger them. With another short press of the power button, you will hear a “door unlocked” tone, which means the top capacitive touch buttons have been unlocked.Was this helpful? Thank you for your feedback!
-
Yes, by using the manual setup procedure it is possible to increase the signal volume level to the subwoofer, while reducing the level on the subwoofer itself. The reason it switches off is that the standby sensing circuit cannot sense music when the level is very low. By increasing the volume to the subwoofer and reducing its output on the sub itself, the signal sensing circuit has a better chance of recognizing an incoming signal, preventing the sub from switching off.Was this helpful? Thank you for your feedback!
-
Move the sub closer to the SOUNDBAR for testing and see if the signal picks up. 1: Turn off any wireless routers or devices that run on 2.4ghz signals, such baby monitors, cordless phones, etc. and test to see if the subwoofer connects. 2: Test with a movie or music with a lot of action scenes or bass. If it's just dialogue, you may not hear the subwoofer.Was this helpful? Thank you for your feedback!
-
The ergonomics of yurbuds sport earphones are indeed different and it is that unique design that creates the TwistLock™ and the guarantee that they will not fall out nor hurt. Our development team studied the human ear, and, as athletes, we know the demands on sport earphones. The results of that research are yurbuds. We encourage you to explore the various offerings on jbl.com.Was this helpful? Thank you for your feedback!
-
If you experience a problem with setup using an Android 7.0 or higher device, please perform the following steps: First, force stop the HK Controller app from running in background. Second, go to your phone or tablet Wi-Fi settings, find the Omni speaker setup Wi-Fi network, and select “Forget Network”.Third, reopen the HK Controller app and begin the setup process again. After performing these steps, you will be able to complete the setup process for your speakers.Was this helpful? Thank you for your feedback!
-
If you suspect a printing error, please contact us. We will ask you take a photo of your Personalised Product. Then we can compare this to the confirmed order image. If the issue is verified, we will provide further instructions to have your Personalised Product re-printed.Was this helpful? Thank you for your feedback!
-
Common fixes:
(1) Make sure that the soundbar is not muted.
(2) Select the correct audio input source on the remote control.
(3) Check the connections to your TV or other devices
(4) Perform a reset if none of the above is working.
(4.1) Press and hold VOL -, VOL +, and Source buttons to perform a reset.
Was this helpful? Thank you for your feedback! -
This is due to your HDMI cables. All cables attached to the HDMI inputs of the SB450, needs to be High speed cables. If your cables do not meet these requirement, then you will experience unstable connection from source to your TV.Was this helpful? Thank you for your feedback!
-
Verify your TV supports the ARC feature.Make sure you enable the external speakers/ARC/digital audio output on your TV, this varies by TV manufacturer. Set the AVR1x1S to the TV input. Go into the AVR menu settings and under System Settings, make sure Audio Return Channel is set to Auto and set the TV Control to on.Was this helpful? Thank you for your feedback!
-
As explained in our Owner's manual, it will adjust the sound to match the placement of your Soundbar, wall or table. When against a wall, the sound reflection will be different than when on a table. This button adjusts the tonal quality to give you the best audio results in either setup.Was this helpful? Thank you for your feedback!
-
This is the charging indicator LED. I lights up red when the headphone is charging, and goes dark when charging is complete, or if no charging takes place.Was this helpful? Thank you for your feedback!
-
Although the owner's manual states that owner can use this connector for home upgrade procedure, this is not so. The USB-connector used cannot be bought in commercially available cables, and the port must be considered for technician's use only.Was this helpful? Thank you for your feedback!
-
Although the owner's manual states that owner can use this connector for home upgrade procedure, this is not so. The USB-connector used cannot be bought in commercially available cables, and the port must be considered for technician's use only.Was this helpful? Thank you for your feedback!
-
For InfinityLab charger, the recommended operating temperature is between 0-45°C.
Our chargers provide auto protection against overheating as well as overcurrent/overvoltage conditions.
Therefore, when the operating temperature is outside the range, this charger will auto adjust the output powers to protect itself and your devices.Was this helpful? Thank you for your feedback! -
If your LINK BAR has 4 orange LED lights in the front, this means you have "muted" the microphone which is located on the top of the speaker.
To unmute the LINK BAR use the "switch" and the front LEDs will stop illuminating orange. Now you can use the hot-words to interact with the Google Assistant/Google Search (varies from country).
Privacy information:
We call our button the "PrivacySwitch" for the moments when you don't want the bar to listen for the hot words.
Google has high privacy rules, and one of them is not to share end-user data with any third-party apps.
Was this helpful? Thank you for your feedback! -
These holes are the microphones for the JBL LinkWas this helpful? Thank you for your feedback!
-
This can be caused by the charge arm reaching its thermal temperature cutoff. This is a safety feature to prevent a potential risk. For proper heat dissipation, always be sure to have the charging arm in the open position when your smart phone is attached.Was this helpful? Thank you for your feedback!
-
Make sure to press the association button once. If by mistake you pressed it more than once, there is a good chance that association does not take place. Wait until the association process is completed, which takes about 2 minutes, and repeat the process.Was this helpful? Thank you for your feedback!
-
True Adaptive NC available on Tour One enables real-time monitoring of exterior surroundings and personal attributes like movement, hair, eyeglasses, and automatic adjustments to the NC performance and EQ.
If you don’t prefer the canceling performance's automatic change, you can get a fine-tuned canceling level by choosing “Everyday Mode” in the app.
Adaptive Noise Cancelling - available on Tour Pro+ TWS - listens to ambient environmental noises using external and internal mics then creates the inverse phase back to the listener creating the noise “canceling” effect.
The headphones also allow the listener to adapt or adjust noise cancellation through features like Ambient Aware and TalkThru.Was this helpful? Thank you for your feedback! -
For 5,000 models, the Max power output is 18W total.
For 10,000 models, the Max power output is 30W total.
It means when charging more than one device simultaneously, total max. output is 18W for 5,000 models and 30W for 10,000 models.
You can also check detailed power output information from the specification on the product page.Was this helpful? Thank you for your feedback! -
For 20W charger, the max. power output is 20W total.
For 30W charger, the max. power output is 30W total.
For 65W charger, the max. power output is 65W total.
For 100W charger, the max. power output is 100W total.
For 30W, 65W and 100W chargers, when charging more than one device simultaneously, total max. power output is 30W, 65W and 100W, respectively. You can also check detailed power output information from specification on product page.Was this helpful? Thank you for your feedback! -
The LED light will be on when the InfinityLAB charger is being powered and it is ready to charge your devices.
The LED light will be off when the power source is off.Was this helpful? Thank you for your feedback! -
Even when reducing volume to minimum on the Bluetooth source unit, it does not reduce the audio signal to zero. In this case the Micro Wireless will playback music at a very low volume.Was this helpful? Thank you for your feedback!
-
The typical values are around 2 & 75 ohms. The default setting is low, we are purposefully not recommending one setting over the other. Headphone impedances can vary (typically in the range of 2 to 300 ohms) and some users may prefer listening with high impedance headphones at the low impedance setting, while others may prefer listening on low impedance headphones at the high impedance setting. Either setting will work with any headphone, so it’s really just a matter of personal listening preference and the user can experiment with the settings. There is no quantifiable performance advantage between the settings - it really just comes down to personal preference. Users can select the setting they like best depending on the type and quality of their headphones, program material, and their own auditory characteristics.Was this helpful? Thank you for your feedback!
-
Your model AVR is equipped with a cooling fan that only comes on when the unit's internal temperature rises above a predetermined limit. Thanks to the massive heat sinks used in the AVR series, this temperature is rarely reached. A typical situation where the fan will come on is when the AVR is operating at a very loud volume level with program material that has sounds in all seven channels. Since this is a rare occurrence, you may never notice the fan working. In any case, when the fan does come on, the volume will be loud enough that you might not notice it. Thus, you may own an AVR for many years and never hear the fan, or see it in operation. There is no way to test the fan, and none is needed.Was this helpful? Thank you for your feedback!
-
If there isn't any input for 10 minutes, the ESQUIRE 2 will go into sleepmode, and after 20 minutes more of no activity, it will power itself off.Was this helpful? Thank you for your feedback!
-
Please note that the digital signal cable for N90Q, which also serves as the charging cable, has a special full-size USB plug that can be inserted the wrong way as well as the correct way into the computer. Always check that charging is actually taking place, by making sure that the charging control light comes on when the USB cable is connected. The amber charging control light is inside the calibration button.Was this helpful? Thank you for your feedback!
-
- HIGH is recommended for Airplanes, City Streets, or other noisy environments.
- LOW is suited for lower noise or windy environments.
- ADAPTIVE will automatically adjust the noise-canceling based on your immediate environment.
- OFF provides passive noise isolation.
Was this helpful? Thank you for your feedback! -
Be aware that the BDS X75 and X77 have two power modes. By pressing the power button briefly, the unit goes into sleep mode, and the fan keeps cooling the unit. Holding down the power button for a couple of seconds puts the BDS into standby, and the fan stops.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00
